Advertisement
Magnetic Base Drilling Machine
Operators Instruction Manual
And Spare Parts Listings
Chapter 1. Technical Overview.
Chapter 2. Warnings and Safety Instructions.
Chapter 3. Operating Instructions.
Chapter 4. Maintenance Instructions.
Chapter 5. Exploded views and Spares lists.
Drill break down and Parts list
Electric motor break down
BD35
Index
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Unibor BD35
Summary of Contents for Unibor BD35
- Page 1 Magnetic Base Drilling Machine BD35 Operators Instruction Manual And Spare Parts Listings Index Chapter 1. Technical Overview. Chapter 2. Warnings and Safety Instructions. Chapter 3. Operating Instructions. Chapter 4. Maintenance Instructions. Chapter 5. Exploded views and Spares lists. Drill break down and Parts list...
- Page 2 This is a high quality product with unique features that make it the perfect solution for your entire hole drilling requirements. ! Easy to use and rugged design makes the BD35 a cost effective solution to drilling clean, accurately positioned holes in your work piece.
-
Page 3: Chapter 1. Technical Overview
Chapter 1. Technical Overview. Machine BD35 Clamping force (Kg) Speed (RPM) Size (LxWxH) (mm) 300x100x390 Cutter Capacity (mm) 12 - 32 Twist Drill Capacity (mm) Power Consumption (Watts) Weight (Kg) -
Page 4: Warnings And Safety Instructions
Chapter 2. Warnings and Safety Instructions. Read these instructions carefully before operating, maintaining or servicing this tool. Please keep these instructions in a safe accessible place. Read to fully understand and Always wear eye, head and ear observe the following safety protection equipment, when precautions and warnings. - Page 5 ! Do not attempt to gain access into the as recommended by the manufacturer. electrical panel. There is risk of electrical Transport and Storage shock. ! Never use a larger diameter cutter than ! Before moving the tool, ensure that the specified for use with this equipment.
-
Page 6: Chapter 3. Operating Instructions
Chapter 3. Operating Instructions. Ensure that the unit is disconnected from the power before working on the machine. ! Insert Pilot Pin. The pilot pin is used to align the cutter and eject the slug on completion of the cut. Slide the pilot through the hole in the centre of the cutter shank. - Page 7 ! Energise the magnet. Switch on the magnetic base by depressing the YELLOW magnet switch. CHECK that the pilot is still aligned with the hole centre mark, as energising the magnetic base can cause the machine to move. ! Apply Coolant A 500ml bottle of cutting oil is supplied with the machine.
-
Page 8: Chapter 4. Maintenance Instructions
Chapter 4. Maintenance Instructions ! Occasionally apply a few drops of oil to the rack toothing. ! The bearings of the feed shaft are self-lubricating and must not be greased ! Grease the sliding surface of the carriage with MOLYCOTE grease. ! When not in use or being transported the unit should be kept in the case supplied. -
Page 9: Chapter 5. Exploded Views
Chapter 5. Exploded Views... -
Page 10: Chapter 5. Component Listing
CCP-19 19mm Internal Circlip VIS08 Drill Guard (not shown) 10091 M10 Guard Locking Nut (not shown) MO241B BD35 Switch Plate STRAP01 Polyester Webbing Safety Strap (not shown) OIL05 Oil Cup Assembly (not shown) OIL09 Coolcut 500ml Oil Bottle (not shown) KEY01 Allen Key 2.5mm (not shown) - Page 11 SC525GRUB M5 x 25mm Grub Screw NUT-M5 M5 Nut SC310CSK-X M3 x 10mm Countersink Screw NUT-M3 M3 Nuts SELPIN410 !4 x 10mm Selop Pin SC410CSK-X M4 x 10mm Countersink Brass (not shown) NUT-M4 M4 Nut Brass (not shown) SC510BUT M5 x 10mm Button Head Screw SC625CAP M6 x 25mm Cap Head Screw SC88GRUB...
- Page 12 Panel Spares Lists - Panel P Item No. Stock Code Description Quantity MM1-1 MM1 MAGNET BUTTON - YELLOW MM1-2 MM1 MOTOR BUTTON - GREEN MM1-10 MM POWER BUTTON - RED MM1-3 MM1 L.E.D. GROMMET MM1-4 MM1 LED BOARD – C/W LEDs MM1-5 MM1 REPLACEMENT PCB MM1-6...
- Page 13 hapter 5. Electric Motor Break Down...
Need help?
Do you have a question about the BD35 and is the answer not in the manual?
Questions and answers