Page 32
The combination of top side and bottom side of this SECTION 8. BOARD LAYOUTS • MAIN-A/B/C UNIT (TOP VIEW) [Side3] [Side2] [PTT] [Side1] DISC R341 C150 R150 CPU5V R170 R143 R145 C221 R115 R378 C138 R405 R377 C429 C442 R113 R114 IC13 C143...
Page 33
The combination of top side and bottom side of this • MAIN-A/B/C UNIT (BOTTOM VIEW) R155 C155 R214 C446 C159 R162 C251 R172 R409 R355 C157 C497 R415 C445 C154 R164 R410 R228 C268 R416 R196 R197 C152 C266 R192 C180 R425 C496...
Page 41
Addresses are provided on the inside back cover for your before connecting it to the transceiver. convenience. Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries.
SECTION 2. INSIDE VIEWS • FRONT UNIT DATA LINE BUFFER (IC709) MIC MUTE SW MIC/AF AMP (Q708) (IC705) AF POWER AMP POWER SUPPLY LINE DRIVER (IC706) (For AF POWER AMP) (Q707) EXPANDER (IC702) BACKLIGHT LED DRIVER (Q705) BACKLIGHT LED SW (Q702) EXPANDER (IC703)
Page 46
• MAIN-A/B/C UNIT (TOP VIEW) AGC AMP (Q41) 1ST IF FILTER D/A CONVERTER (For FM wide mode) (IC33) (FI3) DISCRIMINATOR (X4) 2ND IF FILTER (FI2) 2ND IF FILTER (For FM narrow and digital modes) (FI1) DIGITAL IF AMP (IC13) +5 V REGULATOR DIGITAL IF FILTER (IC11) (FI5)
Page 47
• MAIN-A/B/C UNIT (BOTTOM VIEW) 1ST IF FILTER (For FM narrow and digital modes) (FI4) RIPPLE FILTER (Q24) IF IC VCO SW (IC15) (Q36) VCO SW TRIPLER (Q35) (Q21) VCO SW (Q37) LOCK VOLTAGE BUFFER LV SW (Q22) (Q25) TONE AMP (Q2) PLL IC (IC14)
5) Disconnect the fl at cable from J5, and then remove panel. the FRONT UNIT from the chassis. Screws Knob Knob Antenna nut Remove with; “ICOM Driver (K)” (8960000110) FRONT UNIT Chassis MAIN UNIT FLAT CABLE 2) Remove 2 screws from the chassis. BE CAREFUL about the locks.
Page 49
3. REMOVING THE JACK UNIT 4. REMOVING THE RF UNIT 1) Unsolder 8 points at the dial. 1) Unsolder 4 points as shown. DIAL UNSOLDER RF UNIT UNSOLDER Solder remover VR UNIT Solder remover UNSOLDER Chassis Solder remover Chassis 2) Remove 4 screws from the RF UNIT, and then remove the RF UNIT from the chassis.
SECTION 4. CIRCUIT DESCRIPTION 2ND IF CIRCUIT (MAIN UNIT) 4-1 RECEIVE CIRCUITS The 1st IF signal is applied to the IF IC (IC15, pin 16), which RF CIRCUIT (RF UNIT AND MAIN UNIT) contains the 2nd IF mixer, 2nd IF AMP, demodulator and The RX signal from the antenna is passed through the LPF other circuits.
RX AF CIRCUIT (MAIN AND FRONT UNITS) 4-2 TRANSMIT CIRCUITS The AF signal from the demodulator circuit is applied to the TX AF CIRCUIT (MAIN AND FRONT UNITS) baseband IC (MAIN UNIT: IC4, pin 23). The AF signal from the internal or external microphone (MIC signal) is passed through the MIC SW (FRONT UNIT: The applied AF signal is amplified and adjusted in level, Q708), and applied to the MIC AMP (FRONT UNIT: IC705,...
MODULATION CIRCUIT (MAIN UNIT) 4-3 FREQUENCY SYNTHESIZER CIRCUITS The MIC signal from the TX AF circuit is amplified by the (MAIN UNIT) AMP (IC3), and then applied to the D/A converter (IC9, pin 4) to be adjusted in level. The transceiver has 3 VCOs; RX VCO-A (Q30, D10, D14), RX VCO-B (Q31, D11, D15) and TX VCO (Q32, D9, D12, The level-adjusted signal is applied to the TX VCO (Q32, D9, D13).
4-5 PORT ALLOCATIONS Port Description Name • CPU (MAIN-A/B/C UNIT: IC35) Serial data to the PLL IC (IC14) and D/A Port Description converter (IC9). Name DAST Strobe signal to the D/A converter (IC9). Bandwidth switches (Q27–Q29, D8, D16) Outputs mode (Digital/Analog) switching NWC1 control.
SECTION 5. ADJUSTMENT PROCEDURE 5-1 PREPARATION ▄ REQUIRED TEST EQUIPMENTS EQUIPMENT GRADE AND RANGE EQUIPMENT GRADE AND RANGE CS-F3160/5060 ADJ Modifi ed OPC-1862 CLONING CABLE Adjustment software JIG cable CS-F3160/5060 ADJ (dPMR) (for [DPM-01]) (See the illustration on page 5-2) Frequency range : DC–600 MHz Power attenuation...
Page 55
¤ JIG CABLE OPC-1862 SPEAKER (1 W/8 Ω) AC MILLIVOLTMETER AUDIO GENERATOR (10 mV to 10 V) (300–3000 Hz/1–500 mV) − + − + − Add a jumper wire here 4.7 µF 5 - 2...
Page 56
¤ ADJUSTMENT CHANNELS • For [Low band] version • For [High band] version • For [350 MHz band] version CONVENIENT: The same cloning file is available. Right-click below, and select "Save Embeded File to Disk." For [Low band] version: For [High band] version: For [350MHz band] version: 5 - 3...
Page 57
¤ PC SCREEN EXAMPLE Adjustment setting Transmit output power Modulation balance CTCSS/DTCS deviation Squelch Reference frequency Receive sensitivity RX Lock voltage (Low) RX Lock voltage (High) TX Lock voltage RX Lock voltage preset (Low) RX Lock voltage preset (High) TX Lock voltage preset S-meter FM deviation (Narrow) Deviation (Middle)*...
FREQUENCY ADJUSTMENTS 1) Select an adjustment item using [↑]/[↓] on the PC's keyboard. 2) Set or modify the adjustment value as specifi ed using [←]/[→] on the PC's keyboard, and then push [ENTER]. TRANSCEIVER’S ADJUSTMENT ADJUSTMENT OPERATION VALUE CONDITION ITEM PLL LOCK 1) Connect an RF power meter to the an- "51"...
TRANSMIT ADJUSTMENTS 1) Select an adjustment item using [↑]/[↓] on the PC's keyboard. 2) Set or modify the adjustment value as specifi ed using [←]/[→] on the PC's keyboard, and then push [ENTER]. ADJUST- TRANSCEIVER’S ADJUSTMENT OPERATION MENT VALUE CONDITION ITEM TX OUTPUT 1 •...
RECEIVE ADJUSTMENTS 1) Select an adjustment item using [↑]/[↓] on the PC's keyboard. 2) Set or modify the adjustment value as specifi ed using [←]/[→] on the PC's keyboard, and then push [ENTER]. TRANSCEIVER’S ADJUSTMENT ADJUSTMENT OPERATION VALUE CONDITION ITEM RX SENSITIVITY 1 NOTE: When "RX SENSITIVITY"...
SECTION 6. PARTS LIST [VERSION LIST] [MAIN-A UNIT] (For low band version) PARTS FREQUENCY DESCRIPTION MODEL VERSION SYMBOL LOCATION RANGE (MHz) 1110005310 S.IC AN6123MS 29.3/13.3 USA-01 1180003670 S.REG BD9141MUV-E2 4.8/10.8 400–470 1110005340 S.IC NJM12902V-TE1-#ZZZB 39.5/12.5 USA-02 1110008030 S.IC AK2346BP-E2 40.0/29.0 1110003800 S.IC NJM2904V-TE1-#FMZB 40.1/8.3...
Page 62
[MAIN-A UNIT] (For low band version) [MAIN-A UNIT] (For low band version) PARTS PARTS DESCRIPTION DESCRIPTION LOCATION LOCATION 1750001150 S.VAR HVC383BTRF-E 62.4/13.5 7030007300 S.RES ERJ2GEJ 332 X (3.3K) 31.8/11.2 1750000711 S.VAR HVC350BTRF-E 64.8/21.7 7030005290 S.RES ERJ2GEJ 682 X (6.8K) 31.9/12.6 1720000570 S.VAR MA368(TX) 66.1/22.6...
Page 63
[MAIN-A UNIT] (For low band version) [MAIN-A UNIT] (For low band version) PARTS PARTS DESCRIPTION DESCRIPTION LOCATION LOCATION R153 7030007570 S.RES ERJ2GEJ 122 X (1.2K) 66.4/29.1 R276 7030009710 S.RES ERJ2GEJ 203 X (20K) 26.4/29.1 R154 7030007270 S.RES ERJ2GEJ 151 X (150) 69.0/33.5 R277 7030009710 S.RES ERJ2GEJ 203 X (20K)
Page 64
[MAIN-A UNIT] (For low band version) [MAIN-A UNIT] (For low band version) PARTS PARTS DESCRIPTION DESCRIPTION LOCATION LOCATION R391 7410001140 S.ARR EXB28V104JX 7.8/18.2 4030016930 S.CER C1005 JB 1A 104K-T 35.9/17.0 R392 7030005090 S.RES ERJ2GEJ 104 X (100K) 47.8/32.3 4030018900 S.CER C1005 JB 0J 474K-T 48.9/16.9 R393 7030005090 S.RES ERJ2GEJ 104 X (100K)
Page 89
W1(C) MP10(C) MP8(C) MP802(J) EP1(C) MP46(C) SP1( C) MP45(C) MP22(C) MP31(C) MP47(C) J1(C) MP32(C) EP1(C) (Viewing from the bottom) MP26(C) MP45(C) JACK UNIT MP47(C) MP3(C) MP7(C) MP15(C) MP36(C) MP28(C) MP30(C) MP29(C) MP1(C) MP16(C) MP44(C) MP37(C) MP23(C) MP42(C) VR UNIT MP21(C) MP12*(C) MP24(C) S501(V)
Page 90
The combination of top side and bottom side of this SECTION BOARD LAYOUTS • FRONT UNIT (TOP VIEW) J702 MC701 DS702 J704 C764 INSP- INSP+ C765 EMIC EPTT DS701 C769 C771 MDET C772 DS710 8 - 1...
Page 91
The combination of top side and bottom side of this MC701 • FRONT UNIT (BOTTOM VIEW) MP710 R713 R750 C728 S717 IC702 MP707 R778 IC709 R779 Q709 J701 J701 C726 C746 R737 D705 C724 C722 REST MCIN C714 C716 C737 R733 AFON D704...
Page 92
The combination of top side and bottom side of this • MAIN-A/B/C UNIT (TOP VIEW) [Side3] [Side2] [PTT] [Side1] DISC R341 C150 R150 CPU5V R170 R143 R145 C221 R115 R378 C138 R405 R377 C429 C442 R113 R114 IC13 C143 C176 R384 PWRSW AFVI...
Page 93
The combination of top side and bottom side of this • MAIN-A/B/C UNIT (BOTTOM VIEW) R155 C155 R214 C446 R162 C251 R172 R409 R355 C157 C497 R415 C445 C154 R164 R410 R228 C268 R416 R196 R197 C152 C266 R192 C180 R425 C496 C232...
Page 94
The combination of top side and bottom side of this • JACK UNIT (TOP VIEW) • RF-A/B/C UNIT (TOP VIEW) F601 EP603 R614 D602 R612 EP801 EP802 C608 IC601 C665 B7668B EP803 J801 J801 C632 C633 C664 R615 R620 R624 C642 FI601 EP804...
Page 95
The combination of top side and bottom side of this • JACK UNIT (BOTTOM VIEW) • RF-A/B/C UNIT (BOTTOM VIEW) C637 R616 D601 C662 C625 C641 C661 MP801 C626 C613 R608 C616 C614 L609 L607 C615 C610 C645 C618 Q602 R610 D605 C657...
Page 96
SECTION 9. GENERAL WIRING CHASSIS PGU6NT-CX-100 CHASSIS OPC-1447A FRONT UNIT RF UNIT CHASSIS (RF-A,RF-B,RF-C) EMER OPC-519A EMER J702 CIRQM CIRQM DS711 CHASSIS OPT3 OPT3 OPV3 EMPH LRES TLED TLED ANTENNA FSDA RLED RLED FSCL MDET MDET LCDV MAIN UNIT TXRF FSCL FSCL ISENS...
Need help?
Do you have a question about the IC-F4261DT and is the answer not in the manual?
Questions and answers