Majestic ODSR36A Owners Installation And Operating Manual
Outdoor woodburning fireplace
Hide thumbs
Also See for ODSR36A:
- Homeowner's installation and operating manual (24 pages) ,
- Specifications (4 pages) ,
- Owner's manual (28 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Majestic ODSR36A
Summary of Contents for Majestic ODSR36A
- Page 1 ODSR Series "A" Outdoor Woodburning Fireplace For Models: ODSR36A ODSR42A Homeowner's Installation and Operating Manual SR cover 11/18/97 For use in U.S./Canada Underwriter's Laboratories Report No. MH6018 DO NOT DISCARD THIS MANUAL - Retain for future use. 20006811 8/08 Rev. 7...
-
Page 2: Table Of Contents
Warranty ............23 Proposition 65 Warning: Fuels used in gas, wood- ODSR36A / ODSR42A burning or oil fired appliances, and the products of... -
Page 3: Safety Information
Moisture Resistance Precautions This outdoor fireplace will shed moderate amounts of Majestic Fireplaces and component parts have been water, but is not waterproof. Water and condensing water highly tested and will operate safely when installed in vapor may enter the chase under certain conditions. -
Page 4: Specifications And Framing
(578 mm) Access 14���" (372 mm) 11" 7���" (279 mm) (197 mm) 8" 40" (203 mm) (1016 mm) Fig. 1 ODSR36A specifications and framing. ODSR42A Woodburning Fireplace — Circulating Model 6811 ODSR36 Minimum 26���" specs Rough (667 mm) Opening 9/03 Depth 50"... -
Page 5: Hearth Dimensions
Majestic Fireplaces ODSR Series "A" ® NOTE: When installation is on a hard, flat surface (such as concrete), the surface must be sloped 1/4" per foot away from any structure. Blocking FP1531 Front Width Back Width Depth 1/2” (13 mm) - Page 6 Majestic Fireplaces ODSR Series "A" ® NOTE: If the fireplace is a freestanding unit, it must be located a minimum of 10' (3 m) from the opening of the firebox to a combustible structure. A minimum height of 6'4" (1.9 m) measured from the base of the firebox to the...
-
Page 7: Chimney Requirements
Majestic Fireplaces ODSR Series "A" ® Chimney Requirements - Offset Installations OFFSET CHIMNEY FLUE EXIT RISE CHIMNEY SECTION FP282 30˚ ELBOW 30˚ Elbow Offsets RETURN FP282 ELBOW MBUF 5/26/96 1' 1¹⁄₂' 3' 4' Offset Rise 30˚ 0 0 0 0 3"... -
Page 8: Planning Information
Majestic Fireplaces ODSR Series "A" ® Planning Information Preplanning an installation is very important to ensure safety and to save time and money. An installer must TOTAL INSTALLED predetermine where a fireplace will be set and how the LENGTH LENGTH MODEL SK chimney system will be run. -
Page 9: Chimney Supports
Majestic Fireplaces ODSR Series "A" ® Installation 0 To 10' Insulating Fireplace Enclosure 2' Min. 0 To 10' for Cold Climates Min. 2' Min. If you live in a cold climate, it is not required but Min. highly recommended that you insulate fireplace... -
Page 10: Framing
Majestic Fireplaces ODSR Series "A" ® Framing Chimney Centerline Framing can be constructed before or after the fireplace Actual Centerpoint is set in place, however, most installers build the frame before setting the fireplace. Frame fireplace with 2 x 4 lumber or heavier materials. -
Page 11: Cutting The Hole
Majestic Fireplaces ODSR Series "A" ® Cutting the Hole Cover fireplace collar opening and cut proper sized chimney hole in chimney. The SK8 pipe allows you to run pipe through a typical 16” on center joist without Metal Safety cutting joists. -
Page 12: Installing Outside Air Kit
Majestic Fireplaces ODSR Series "A" ® Installing Outside Air Kit Elbow Strap Support Structure An outside air kit is not installed in all ODSR Series "A" Fireplaces. If desired, or if local codes mandate the use of an air kit, then an AKU1 is required . If the outside air kit is to be used, the AKU1 MUST be installed BEFORE the fireplace is enclosed. - Page 13 Majestic Fireplaces ODSR Series "A" ® Chimney Supports Attic Installation If chimney supports are required, they are installed the Nails (4) same as elbows. Nail chimney support straps to adja- cent structural framing, as shown on, Page 9, Figure Firestop 10.
-
Page 14: Finishing
Majestic Fireplaces ODSR Series "A" ® Cut and frame the hole. It is good practice to use fram- Air Space Clearances ing lumber that is the same size as the rafters. Install the frame securely because the chimney top and flash-... - Page 15 Majestic Fireplaces ODSR Series "A" ® Mantel Clearance - Mantel Clearance - with Noncombustible Facing Material No Noncombustible Facing Material Combustible Mantel 12" 12" Combustible Mantel and Trim (305mm) and Trim (305mm) Finished Wall Finished Wall Max. Max. 1¹⁄₂" 1¹⁄₂"...
-
Page 16: Side Wall Protection
Majestic Fireplaces ODSR Series "A" ® Hearth Installation Side Wall Protection A hearth extension is required to protect a combustible Adjacent combustible side walls that are within the mini- floor in front of the fireplace. Refer to Figure 24 for mini- mum dimensions shown in Figure 24 of fireplace open-... - Page 17 Majestic Fireplaces ODSR Series "A" ® Side View COMMON MATERIALS AND FACTORS Wall Covering MINIMUM MATERIAL THICKNESS Noncombus- 2 x 4 Header EH2416 tible Decorative (Do not notch 0.458 1.09 0.50 in.** (MHSC) Facing at standoffs) Seal all cracks between fireplace sur- Common Brick 0.10...
-
Page 18: Installing Line For Gas Logs
Installing Line for Gas Logs Fireplace Top View Hole in Outer Casing Majestic fireplaces are designed to accept a 1/2" (13 mm) gas line for installation of an approved gas appli- ance. (MHSC manufactures a wide variety of gas logs 1"... -
Page 19: Replacement Parts
ODSR Series "A" ® 6811 MHSC reserves the right to make changes in design, materials, specifications, prices and discontinue colors and products at any time, without notice. ODSR36A/42A Outdoor Woodburning Fireplace Item/Model Number ODSR36A ODSR42A 1. Damper Weld Assembly RP199 RP199 2. -
Page 20: Accessories
ODSR Series "A" ® Accessories The following accessories for this appliance are available from your local Majestic distributor. Should you need addi- tional information beyond what your distributor can furnish, contact: MHSC, 149 Cleveland Drive, Paris, KY 40361, Attn: Technical Services. -
Page 21: Chimney Components
Majestic Fireplaces ODSR Series "A" ® Chimney Components U.S. Component Description Model Number Round Top Termination Top used to terminate chimney at roof. RLTSK8 (Flashing not included.) Round Top Termination - Top used to terminate chimney at chase. RLTSK8L Extended (Flashing not included.) - Page 22 Majestic Fireplaces ODSR Series "A" ® (Chimney Components con't.) Canada Component Description Model Number Chimney Collar Enclosure Installs on the "over the chimney collar" of the CCE-SK fireplace; provides outside air to assist in cooling the chimney system. Attic Insulation Shield...
-
Page 23: Warranty
Majestic Fireplaces ODSR Series "A" ® LIMITED WARRANTY Factory-Build Fireplace and Components (Except Blowers) What is Covered and For How Long Five-Year Coverage: For five years from the date this fireplace and components are first purchased for use, MHSC will, at its option, repair or replace any defective part of this fireplace or components, or refund to you a sum not to exceed the factory retail price in effect at the time of purchase. - Page 24 MHSC 149 Cleveland Drive • Paris, Kentucky 40361 www.mhsc.com...
Need help?
Do you have a question about the ODSR36A and is the answer not in the manual?
Questions and answers