The BR/BC Series fireplaces are solid fuel, woodburning products not specified for use with this fireplace. fireplaces. The BR36/42 (Builder Radiant) is a clean-face These fireplaces are not approved for installation in fireplace and the BC36/42 (Builder Circulating) unit has mobile homes.
13¹⁄₄" Electrical Access (337mm) If elbows are offset to the back of the unit, chase depth will be 22⁵⁄₈" (575mm). FP526 Fig. 1 BR36 Series specifications and framing. BC36 Series Woodburning Fireplace — Circulating Model 22" (559mm) Rough Opening Depth 11"...
Majestic Fireplaces BR/BC Series ® Chase Installation Insulation methods shown are optional for cold climate, not a requirement for unit operation. Termination Cap Storm Collar Pan Flashing Batt Insulation (cut our around firestop) Draftstop Firestop Ceiling Level Standoff Surround Damper Control...
Majestic Fireplaces BR/BC Series ® Planning Information Preplanning an installation is very important to ensure 4. The maximum length of an angled run (total chim- safety and to save time and money. An installer must ney system) is 20' (6m).
When installing the chimney, DO NOT caulk between Majestic Fireplaces dealer for assistance. outer pipe and firestop. It is vital that some air be allowed to flow through this very thin gap.
Page 9
Majestic Fireplaces BR/BC Series ® Framing Option For Circulating Models Only — Framing can be constructed before or after the fire- EB1 (Receptacle) Hook-Up: place is set in place, however, most installers build the frame before setting the fireplace. • Wiring should be installed by a certified Frame fireplace with 2 x 4 lumber or heavier materials.
Page 10
Majestic Fireplaces BR/BC Series ® Determine offset distance of your chimney arrangement Straight-Up Chimney Installation from centerline of fireplace to centerline of chimney To mark the centerline of the flue, put the fireplace in where it is to pass through ceiling.
Page 11
Majestic Fireplaces BR/BC Series ® The following table gives firestop spacer model num- Installing Outside Air Kit bers: An outside air kit is installed in all BR/BC Series Fire- Angle of Chimney at Ceiling places. If desired, or if local codes mandate the use of...
Page 12
Majestic Fireplaces BR/BC Series ® Installing the Chimney System Pipe Section Start by attaching the first chimney section to the collar Pipe on top of the fireplace. Install the pipe as pictured in Figure 16. When you get Lance a good lock, you will hear the pipe clearly snap to- Pipe gether.
Page 13
Majestic Fireplaces BR/BC Series ® Firestop spacers are not available for nor are they required on vertical walls. DO NOT put any sealant around the area where the Attic outer pipe slides through the firestop spacer. If you Insulation Shield seal this area, it may cause a fire hazard.
Page 14
Majestic Fireplaces BR/BC Series ® Install Remainder of Chimney Sections Air Space Clearances Since you have already preplanned the height of your Combustible framing material MUST NOT termination according to the Ten Foot Rule , continue to penetrate AIR SPACE (shaded areas).
Page 15
Majestic Fireplaces BR/BC Series ® Mantel Clearance - Radiant Mantel Clearance - Mantel Clearance - Radiant Model - No Model - with Noncombustible Circulating Model Noncombustible Facing Material Facing Material Combustible Combustible Combustible Mantel and Mantel and Mantel and 12"...
Page 16
Majestic Fireplaces BR/BC Series ® Side Wall Protection Hearth Installation Adjacent combustible side walls that are within mini- A hearth extension is required to protect a combustible mum dimensions shown in Figure 23 of the fireplace floor in front of the fireplace. Refer to Figure 23 for opening must be protected with CFM Corporation Wall minimum dimensions and mounting detail.
Page 17
Majestic Fireplaces BR/BC Series ® WARNING: HEARTH EXTENSION MUST BE IN- Wall Covering STALLED IN ACCORDANCE WITH FIGURE 23 AND MUST NOT COVER THE BOTTOM FRONT OPENING Noncombustible 2 x 4" HEADER - Decorative OF THE CIRCULATING MODEL. Do not notch at Facing standoffs.
Page 18
Majestic Fireplaces BR/BC Series ® Installing Line For Gas Log Hole in Outer Casing Fireplace Top View CFM Specialty Home Products fireplaces are designed to accept a 1/2 inch gas line for installation of an approved gas appliance. (CFM Specialty Home 1"...
Majestic Fireplaces BR/BC Series ® CFM Specialty Home Products reserves the right to make changes in design, materials, specifications, prices and discontinue colors and products at any time, with out notice. BR/BC SERIES For units: FA30C1, FA30C0, FA30R1, FA30R0, GA30C1, GA30C0, GA30R1, GA30R0, FA40C1, FA40C0, FA40R1,...
® Accessories The following accessories for this appliance are available from your local Majestic Fireplaces distributor. Should you need additional information beyond what your distributor can furnish, contact: CFM Specialty Home Products, 410 Admiral Blvd., Mississauga, Ontario, Canada L5T 2N6, Attn: Technical Services.
Page 21
Majestic Fireplaces BR/BC Series ® Chimney Components U.S. Component Description Model Number Round Top Termination Top used to terminate chimney at roof. (Flashing not included.) RLTSK8 Round Top Termination - Top used to terminate chimney at chase. Extended (Flashing not included.)
Page 22
Majestic Fireplaces BR/BC Series ® (Chimney Components con't.) Canada Component Description Model Number Chimney Collar Enclosure Installs on the "over the chimney collar" of the CCE-SK fireplace; provides outside air to assist in cooling the chimney system. Attic Insulation Shield...
Page 23
(4)CFM Specialty Home Products shall not be liable for installed, CFM Specialty Home Products, at its option, will repair damage from any smoking of a MAJESTIC FIREPLACES Pre- or replace any defective part without charge. Engineered Fireplace System related to environmental geo-...
Need help?
Do you have a question about the BR36 and is the answer not in the manual?
Questions and answers