Advertisement
INSTALLATION AND OPERATION INSTRUCTIONS
IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION INSTRUCTIONS
INTRODUCTION
This remote control system was developed to provide a safe, reliable, and user-friendly remote control system for gas heating
appliances or other compatible appliances. The system can be operated manually from the transmitter.
Review COMMUNICATION SAFETY under TRANSMITTER section and THERMO SAFETY under REMOTE RECEIVER section.
These signal/temperature safety features shut down the fireplace system when a potentially unsafe condition exists.
MODE
DOWN
UP
Cover Closed
Cover
Open
1.
MODE - Switches the appliance on/thermo/off.
2.
UP and DOWN - Used to change the time, set temp, and programming functions.
3.
SET - Used in different functions to confirm settings.
4.
PROG - Turns off and on program function.
LCD – LIQUID CRYSTAL DISPLAY
8
2
4
6
_________________________________________________________________________________________________
Skytech 3301P2
Model: 3301P2
DO NOT ATTEMPT TO INSTALL OR OPERATE
The transmitter operates on (2) AAA 1.5V batteries that are included. Install the
batteries supplied with the unit into the battery compartment. It is recommended
that ALKALINE batteries always be used for this product. Be sure the batteries
are installed with the (+) and (-) ends facing the correct direction.
When you start up the remote, if a low battery signal appears or if they LCD
MODE
screen does not illuminate, check battery position and if the batteries are fully
DOWN
UP
charged.
PROG
SET
1. LOW BATTERY - Battery power is low. Replace Batteries in 2 - 4 weeks.
2. MODE - Indicates operation mode of system.
7
3. FLAME- Indicates the burner/valve in operation.
9
4. ROOM - Indicates CURRENT room temperature.
5. SET- Indicates desired SET room temperature in Thermo operation.
6. FAHRENHEIT/CELSIUS – Indicates degrees Fahrenheit or Celsius.
1
7. DAY OF WEEK – Indicates current day of week, or program segment when editing
program settings.
5
8. PROGRAM ON/OFF – Indicates when Program 1 (P1) is on or off, and indicates
when Program 2 (P2) is on or off.
3
9. TIME and PROGRAM TIME – Indicates current time or program time setting when
editing program settings.
1
MODE
DOWN
UP
2
4
PROG
3
SET
REV. 8/3/11 Page 1 of 7
Advertisement
Table of Contents
Related Manuals for Skytech 3301P2
Summary of Contents for Skytech 3301P2
- Page 1 Model: 3301P2 INSTALLATION AND OPERATION INSTRUCTIONS IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION INSTRUCTIONS DO NOT ATTEMPT TO INSTALL OR OPERATE INTRODUCTION This remote control system was developed to provide a safe, reliable, and user-friendly remote control system for gas heating appliances or other compatible appliances.
-
Page 2: Mode Function
THERMO UPDATING FEATURE - TRANSMITTER When in thermo mode, the transmitter reads the ROOM temperature every 2 minutes, checks the room temperature against the SET temperature then sends a signal to the receiver. _________________________________________________________________________________________________ Skytech 3301P2 REV. 8/3/11 Page 2 of 7... -
Page 3: Program Function
“MTWTF” (Weekday Segment) will replace “S S”. P1 ON will be flashing. Repeat the above steps to set the ON and OFF times and set temperatures for weekdays. (See Fig. #6). _________________________________________________________________________________________________ Skytech 3301P2 REV. 8/3/11 Page 3 of 7... - Page 4 Switch transmitter on initial use, check the battery positions in the remote. If that does not REMOTE work, see the LEARNING TRANSMITTER TO RECEIVER section. OFF: will disable the remote receiver. _________________________________________________________________________________________________ Skytech 3301P2 REV. 8/3/11 Page 4 of 7...
-
Page 5: Installation
Be sure that the connectors do not touch each other or other bare metal surfaces; this will cause the appliance to turn ON. The connectors may be wrapped with electrical tape to prevent this. REMOTE _________________________________________________________________________________________________ Skytech 3301P2 REV. 8/3/11 Page 5 of 7... - Page 6 When you release the LEARN button the receiver will emit an audible “beep”. After the receiver emits the beep press the transmitter MODE button and release. The receiver will emit several beeps indicating that the transmitter’s code has been accepted into the receiver. _________________________________________________________________________________________________ Skytech 3301P2 REV. 8/3/11 Page 6 of 7...
-
Page 7: Troubleshooting
MODIFICATIONS TO THE EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT For Technical Service, call: U.S. INQUIRIES CANADIAN INQUIRIES (888) 672-8929 or (260) 459-1703 (888) 472-3923 Web site: www.skytechsystem.com MANUFACTURED EXCLUSIVELY FOR SKYTECH II, INC _________________________________________________________________________________________________ Skytech 3301P2 REV. 8/3/11 Page 7 of 7... -
Page 8: Limited Lifetime Warranty
Replacement parts will be available at no charge for the first (5) five years of this warranty, and will be available at market cost for the Lifetime of the product to that original owner. If SKYTECH II does not have the parts for an individual model, then a replacement SYSTEM will be provided. - Page 9 Exclusive offer to Skytech Remote Control Owners This special offer is only provided to customers of Skytech II, Inc. that have purchased a remote control for their Hearth Product. This remote control system can be used for any 110Volt appliance, but perfect your Christmas Tree Lights or any other appliance that is difficult to reach or plug in.