Table of Contents
Advertisement
Quick Links
See also:
User Manual
Copyright
This publication, including all photographs, illustrations and software, is protected
under international copyright laws, with all rights reserved. Neither this manual, nor
any of the material contained herein, may be reproduced without written consent of
the author.
Version 1.0
Disclaimer
The information in this document is subject to change without notice. The
manufacturer makes no representations or warranties with respect to the contents
hereof and specifically disclaims any implied warranties of merchantability or fitness
for any particular purpose. The manufacturer reserves the right to revise this
publication and to make changes from time to time in the content hereof without
obligation of the manufacturer to notify any person of such revision or changes.
Trademark Recognition
Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.
MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel
Corporation.
Other product names used in this manual are the properties of their respective owners
and are acknowledged.
Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
−
−
Increase the separation between the equipment and the receiver.
−
Connect the equipment onto an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
−
Shielded interconnect cables and a shielded AC power cable must be employed with
this equipment to ensure compliance with the pertinent RF emission limits governing
this device. Changes or modifications not expressly approved by the system's
manufacturer could void the user's authority to operate the equipment.
Preface
Advertisement
Table of Contents
Related Manuals for Syntax SV266A
Summary of Contents for Syntax SV266A
- Page 1 Preface Copyright This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author. Version 1.0 Disclaimer The information in this document is subject to change without notice.
-
Page 2: Declaration Of Conformity
Declaration of Conformity This device complies with part 15 of the FCC rules. Operation is subject to the following conditions: This device may not cause harmful interference, and − This device must accept any interference received, including interference − that may cause undesired operation. Canadian Department of Communications This class B digital apparatus meets all requirements of the Canadian Interference- causing Equipment Regulations. - Page 3 Un CD d'installation automatique pour le logiciel Ce manuel utilisateur • Caractéristiques Processeur La carte mère SV266A utilise un Socket A AMD 462 broches présentant les caractéristiques suivantes: Supporte un bus frontal (FSB) de 100/133 MHz • • Reçoit des processeurs Athlon/Duron AMD...
- Page 4 Graphiques La carte mère comprend un logement AGP qui offre quatre fois la bande passante des spécifications AGP d’origine. La technologie AGP offre une connexion directe entre le sous-système graphique et le processeur de sorte que les graphiques n’ont pas à entrer en concurrence avec d’autres périphériques pour le temps d’utilisation du processeur sur le bus PCI.
- Page 5 • Eine Auto-Installations-Support-CD Dieses Benutzerhandbuch • Features Prozessor Das SV266A Mainboard enthält einen AMD 462-Pin Sockel A mit den folgenden Eigenschaften: Unterstützt 100/133 MHz Front-Side Bus (FSB) • • Nimmt AMD Athlon/Duron Prozessoren auf Die Chipsätze KT266A Northbridge und VT8235 Southbridge Chipsatz basieren auf einer kostengünstigen und energiesparenden...
- Page 6 Speicher Das Mainboard nimmt die folgenden Speicherkonfigurationen auf: DDR (Double Data Rate) PC1600/PC2100 SDRAM • unterstützt bis zu 2 GB unter Verwendung von zwei 2.5V DIMM-Modulen SDRAM PC133/ PC100 unterstützt bis zu 2 GB unter • Verwendung von zwei 3.3V DIMM-Modulen Audio Der Audio-Codec ist kompatibel mit der AC 97 2.2- Spezifikation und unterstützt 18-Bit ADC (Analog Digital...
- Page 7 Un CD di supporto software auto-installante Il manuale dell’utente • Caratteristiche Processore La scheda madre SV266A usa un socket AMD 462-pin Socket A con le seguenti caratteristiche: Supporto per il bus di sistema frontside (FSB) 100/133 • • Alloggia processori AMD Athlon/Duron.
- Page 8 DDR (Double Data Rate) PC1600/PC2100 SDRAM con • supporto fino a 2 GB con due moduli DIMM 2.5V • SDRAM PC133/ PC100 supporta fino a 2 GB usando due moduli DIMM 3,3V. Audio Il code audio è compatibile con le specifiche AC 97 2.2 e supporta una risoluzione a 18 bit ADC (convertitore analogico digitale) e DAC (convertitore digitale analogico) come pure codec full duplex 18 bit con frequenze di campionamento...
- Page 9 Un CD de soporte en software de autoinstalación • Este manual del usuario Características Procesador La placa principal SV266A usa una AMD 462-pin Socket A que tiene las sigtes. características: • Soporta bus de lado frontal (FSB) 100/133 MHz Acomoda procesadores AMD Athlon/Duron •...
- Page 10 tecnología AGP provee una conexión directa entre el subsistema de gráficas y el procesador para que las gráficas no tengan que competir por el tiempo de procesador con otros dispositivos en el bus PCI. Sonido El codec de sonido se conforma con la AC 97 2.2, y soporta 18-bit ADC (Conversor Digital Analógico/Analog Digital Converter) y resolución DAC (Conversor Analógico Digital/Digital Analog Converter) y también codec de full-duplex...
- Page 11 • • • • CD 1 • SV266A AMD 462 • 100 / 1 3 3 MHz (FSB) • AMD Ath l o n /Du r o n KT266A Nor thb r i d g e VT8235 Southb r i d g e AGP/ •...
- Page 12 • • • • CD 1 • • SV266A AMD 462 100 /133 MHz f r on t s i d e bus (FSB) • • AMD Ath lon /Du ron KT266A Nor thb r i d ge VT8235 Southbr i d ge AGP/PCI •...
- Page 13 DDR SDRAM • USB 2.0 • • Ul t r a DMA 33/66 / 100 / 1 33 EIDE AC 97 . AGP • DDR (Doub le Data Rate) PC1600/PC2100 SDRAM 2.5V DIMM 2 GB • SDRAM PC133/ PC100 3.3V DIMM AC 97 2.2 ADC (Ana l og Dig i t a l Conver t e r )
- Page 14 • • • • • SV266A AMD 462 Sock e t • 100 / 1 3 3MHz (FSB) • AMD Ath lon / Duron KT266A VT8235 AGP/PCI • Sock e t - A (Soc k e t - 462 ) AMD Ath l on •...
- Page 15 • – 100/10 Mbps • IEEE 802.3, 10BaseT 100Base-Tx , • • • PS/2 • • • 4 USB • 1 LAN • l i n e - in l i n e - ou t AWARD BIOS BIOS • •...
- Page 16 • • • I DE • • • SV266A AMD 462 p i n Socke t A • 100 /133 MHz (FSB ) • AMD Ath l o n /Du r o n KT266A VT8235 AGP/PCI • Socke t A (Soc ke t 462 ) AMD Ath l o n •...
- Page 17 I /O • PS/2 • • • • • BIOS Award BIOS • • • • ABLE ONTENTS ABLE ONTENTS Preface......................i Features and Packing List Translations............iii CHAPTER 1 Introducing the Mainboard................1 Introduction....................1 xvii...
-
Page 18: Table Of Contents
Checklist......................1 Standard Items....................1 Features......................2 Choosing a Computer Case................3 Mainboard Components................4 CHAPTER 2 Installing the Mainboard................6 Safety Precautions..................6 Quick Guide....................6 Installing the Mainboard in a Case..............7 Checking Jumper Settings................7 Setting Jumpers....................7 Checking Jumper Settings................8 Jumper Settings....................8 Connecting Case Components..............10 Front Panel Connector...................11 Installing Hardware...................12 Installing the Processor..................13 Installing Memory Modules................15... - Page 19 CHAPTER 4 Using the Mainboard Software..............50 About the Software CD-ROM..............50 Auto-installing under Windows 98/ME/2000/XP........50 Running Setup....................51 Manual Installation ...................53 Utility Software Reference................53...
-
Page 21: Checklist
Introducing the Mainboard Introduction Introduction Thank you for choosing the SV266A mainboard. The SV266A is a high perfor- mance and high quality mainboard which is built around the latest and fastest VIA KT266A + VT8235 chipset providing superior performance between the CPU, DRAM, AGP bus, and V-Link bus with pipelined, burst and concurrent operation. -
Page 22: Features
Features Features Processor The SV266A mainboard uses an AMD 462-pin Socket A that has the following features: Supports 100/133 MHz frontside bus (FSB) • • Accommodates AMD Athlon/Duron processors Chipset The KT266A Northbridge and VT8235 Southbridge chipsets are based on cost-effective and energy efficient chipset architecture for implementing AGP/PCI desktop personal computer systems with proven reliability and performance. -
Page 23: Choosing A Computer Case
Onboard LAN The VT6103 is a Physical Layer device for Ethernet 10BASE-T (optional) and 100BASE-TX using category 5 Unshielded, Type 1 Shielded cables Dual Speed – 100/10 Mbps • • Half And Full Duplex Meet All Applicable IEEE 802.3, 10Base-T and •... -
Page 24: Mainboard Components
Mainboard Components Mainboard Components... - Page 25 Table of Mainboard Components Label Component AGP1 Accelerated Graphics Port ATX1 Power connector AUDIO1 Front-oriented microphone/line-out port header AUXIN1 Extra line-in connector Three volt realtime clock battery CASEFAN1 Auxiliary case cooling fan CD-in connector CNR1 Communications Networking Riser slot CPUFAN1 Cooling fan for CPU CPU Socket Socket A for AMD Athlon processor...
-
Page 26: Installing The Mainboard
Chapter 2 Chapter 2 Installing the Mainboard Safety Precautions Safety Precautions Follow these safety precautions when installing the mainboard: • Wear a grounding strap attached to a grounded device to avoid damage from static electricity. Discharge static electricity by touching the metal case of a safely •... -
Page 27: Installing The Mainboard In A Case
Installing the Mainboard in a Case Installing the Mainboard in a Case Refer to the following illustration and instructions for installing the mainboard in a case: This illustration shows an 2. Secure the mainboard with example of a mainboard being screws where appropriate. -
Page 28: Checking Jumper Settings
Checking Jumper Settings The following illustration shows the location of the mainboard jumpers. Pin 1 is labeled. Jumper Settings Jumper Type Description Setting (default) 3 pin Clear CMOS 1-2: Normal 2-3: Clear 3 pin CPU frequency 1-2: 100MHz select 2-3: 133 MHz JP5A 80 pin DDR/SDR... - Page 29 JP6A 80 pin DDR/SDR JP6A/B/C/D Short all JP6A/B/ JP6B DRAM Type C/D: DDR JP6C Selector memory JP6D Open all JP6A/B/ C/D: SDR memory Jumper 1 – enables you to clear the BIOS. Follow these instructions: Turn the system off. Short pins 2 and 3 on JP1. Return the jumper to the normal setting.
-
Page 30: Connecting Case Components
Connecting Case Components Connecting Case Components After you have installed the mainboard into a case, you can begin connecting the mainboard components. Refer to the following: Connect the case power supply connector to ATX1. Connect the CPU cooling fan cable to CPUFAN1. -
Page 31: Front Panel Connector
SPEAKER1: Internal speaker Signal Name Signal Ground J1: Case open detecting connector (optional) This connector allows the user to detect unauthorized intrusion to the case. It will alert the user with a warning message when the case is turned on. Signal Name Function Intruder... -
Page 32: Installing Hardware
The front panel connector (PANEL1) provides a standard set of switch and LED connectors commonly found on ATX or micro-ATX cases. Refer to the table below for information: Function Function Hard disk LED MSG LED [dual color (positive) or single color (+)] Hard disk active LED MSG LED [dual color (negative) -
Page 33: Installing The Processor
Installing the Processor Caution: When installing a CPU heatsink and cooling fan make sure that you DO NOT scratch the mainboard or any of the surface-mount resistors with the clip of the cooling fan. If the clip of the cooling fan scrapes across the mainboard, you may cause serious damage to the mainboard or its components. -
Page 34: Cpu Installation Procedure
CPU Installation Procedure The following illustration shows CPU installation components: Note: The pin-1 corner is marked with an arrow Follow these instructions to install the CPU: Pull the CPU socket locking lever away from the socket to unhook it and raise the locking lever to the upright position. -
Page 35: Installing Memory Modules
Connect the CPU Cooling Fan power cable connector to the CPUFAN connector. • To achieve better airflow rates and heat dissipation, we suggest that Notes you use a high quality fan with 4800 rpm at least. CPU fan and heatsink installation procedures may vary with the type of •... - Page 36 Refer to the following to install the memory modules. Push the latches on each side of the DIMM slot down. Align the memory module with the slot. The DIMM slots are keyed with notches and the DIMMs are keyed with cutouts so that they can only be installed correctly.
-
Page 37: Installing A Hard Disk Drive/Cd-Rom
Installing a Hard Disk Drive/CD-ROM This section describes how to install IDE devices such as a hard disk drive and a CD-ROM drive. About IDE Devices Your mainboard has a primary and secondary IDE channel interface (IDE1 and IDE2). An IDE ribbon cable supporting two IDE devices is bundled with the main- board. - Page 38 Installing a CD-ROM/DVD Drive Install the CD-ROM/DVD drive into the drive cage in your system case. Plug the IDE cable into IDE1 (A). If you have already installed an HDD, use the other connector on the IDE cable. Note: Ribbon cable connectors are usually keyed so that they can only be installed correctly on the device connector.
-
Page 39: Installing A Floppy Diskette Drive
Installing a Floppy Diskette Drive The mainboard has a floppy diskette drive (FDD) interface and ships with a diskette drive ribbon cable that supports one or two floppy diskette drives. You can install a 5.25-inch drive and a 3.5-inch drive with various capacities. The floppy diskette drive cable has one type of connector for a 5.25-inch drive and another type of connector for a 3.5-inch drive. -
Page 40: Installing Add-On Cards
Installing Add-on Cards The slots in this mainboard are designed to hold expansion cards and connect them to the system bus. Expansion slots are a means of adding or enhancing the mainboard’s features and capabilities. With these efficient facilities, you can increase the mainboard’s capabilities by adding hardware which performs tasks that are not part of the basic system. -
Page 41: Connecting Optional Devices
Follow these instructions to install an add-on card: Remove a blanking plate from the system case corresponding to the slot you are going to use. Install the edge connector of the add-on card into the expansion slot. Ensure that the edge connector is correctly seated in the slot. - Page 42 Refer to the following for information on connecting the mainboard’s optional devices: AUDIO1: Front Panel Audio header This header allows the user to install auxiliary front-oriented microphone and line-out ports for easier access. Signal Name Function AUD_MIC Front Panel Microphone input signal AUD_GND Ground used by Analog Audio Circuits AUD_MIC_BIAS...
- Page 43 USB3: Front panel USB connectors The mainboard has four USB ports installed on the rear edge I/O port array. Additionally, some computer cases have USB ports at the front of the case. If you have this kind of case, use auxiliary USB connectors USB3 to connect the front-mounted ports to the mainboard.
-
Page 44: Connecting I/O Devices
USBCR1: USB Card Reader connector This connector is for connecting internal USB card reader. You can use a card reader to read or transfer files and digital images to your computer. Signal Name Function USBVCC2 +5V dual USB2- Data signal port 2- USB2+ Data signal port 2+ Ground... -
Page 45: External Connector Color Coding
External Connector Color Coding Many connectors now use standard colors as shown in the table below. Connector Color Audio line-in Light blue Audio line-out Lime Microphone Pink Parallel Burgundy PS/2-compatible keyboard Purple PS/2-compatible mouse Green Serial Teal or Turquoise Black This concludes Chapter 2. -
Page 46: Chapter 3 Using Bios
Chapter 3 Chapter 3 Using BIOS About the Setup Utility About the Setup Utility The computer uses the latest Award BIOS with support for Windows Plug and Play. The CMOS chip on the mainboard contains the ROM setup instructions for configuring the mainboard BIOS. The BIOS (Basic Input and Output System) Setup Utility displays the system's configuration status and provides you with options to set system parameters. -
Page 47: Starting Setup
Starting Setup The BIOS is immediately activated when you first turn on the computer. The BIOS reads system configuration in CMOS RAM and begins the process of checking out the system and configuring it through the power-on self test (POST). When these preliminaries are finished, the BIOS seeks an operating system on one of the data storage devices (hard drive, floppy drive, etc.). -
Page 48: Updating The Bios
BIOS Navigation Keys The BIOS navigation keys are listed below: Function Exits the current menu Scrolls through the items on a menu ←↑↓→ +/–/PU/PD Modifies the selected field's values Saves the current configuration and exits setup Displays a screen that describes all key functions Loads previously saved values to CMOS Loads a minimum configuration for troubleshooting. -
Page 49: Using Bios
When the installation is complete, remove the floppy diskette from the diskette drive and restart your computer. If your mainboard has a Flash BIOS jumper, reset the jumper to protect the newly installed BIOS from being overwritten. Using BIOS Using BIOS When you start the Setup Utility, the main menu appears. - Page 50 ever you make changes to the Windows Date and Time Properties utility. IDE Devices (None) Your computer has two IDE channels (Primary and Secondary) and each channel can be installed with one or two devices (Master and Slave). Use these items to configure each device on the IDE channel. Press <Enter>...
-
Page 51: Advanced Bios Setup
Drive A/Drive B (1.44M, 3.5 in./None) These items define the characteristics of any diskette drive attached to the system. You can connect one or two diskette drives. Video (EGA/VGA) This item defines the video mode of the system. This mainboard has a built-in VGA graphics system;... - Page 52 Most processors that can be installed in this system use external level 2 (L2) cache memory to improve performance. Leave this item at the default value for better performance. CPU L2 Cache ECC Checking (Enabled) This item enables or disables ECC (Error Correction Code) error checking on the CPU cache memory.
-
Page 53: Advanced Chipset Setup
• Typematic Delay (Msec): Use this item to define how many milliseconds must elapse before a held-down key begins generating repeat characters. Security Option (Setup) If you have installed password protection, this item defines if the password is required at system start up, or if it is only required when a user tries to enter the Setup Utility. - Page 54 DRAM Clock/Drive Control Scroll to this item and press <Enter> to view the following screen: CMOS Setup Utility – Copyright (C) 1984 – 2001 Award Software DRAM Clock/Drive Control Item Help Current FSB Frequency Current DRAM Frequency Menu Level DRAM Clock [By SPD] DRAM Timing [By SPD]...
- Page 55 DRAM Burst Length (4) This item describes which burst lengths are supported by the devices on the mainboard. 1 level can provide faster performance but may result in instability whereas 8 level gives the most stable but slowest performance. DRAM Queue Depth (4 level) This item sets the depth of the DRAM queue used for CPU’s cache.
-
Page 56: Integrated Peripherals
Item Help PCI1 Master 0 WS Write [Enabled] PCI2 Master 0 WS Write [Enabled] Menu Level PCI1 Post Write [Enabled] PCI2 Post Write [Enabled] PCI Delay Transaction [Disabled] ↑ ↑ ↑ ↑ ↓ ↓ ↓ ↓ → → → → ← ← ← ← : Move Enter : Select +/-/PU/PD:Value: F10: Save ESC:... - Page 57 Item Help USB 2.0 Support [Enabled] OnChip IDE Device [Press Enter] Menu Level OnChip PCI Device [Press Enter] Super I/O Device [Press Enter] Init Display First [PCI Slot] OnChip USB Controller [All Enabled] USB keyboard Support [Disabled] IDE HDD Block Mode [Enabled] PWRON After PWR-Fail [Off]...
- Page 58 IDE Primary/Secondary Master/Slave UDMA (Auto) Each IDE channel supports a master device and a slave device. This main- board supports UltraDMA technology, which provides faster access to IDE de- vices. If you install a device that supports UltraDMA, change the appropriate item on this list to Auto.
- Page 59 Item Help Onboard FDC Controller [Enabled] Onboard Serial Port 1 [3F8/IRQ4] Menu Level Onboard Serial Port 2 [2F8/IRQ3] UART Mode Select [Normal] UR2 Duplex Mode [Half] Onboard Parallel Port [378/IRQ7] Parallel Port Mode [ECP] ECP Mode Use DMA Game Port Address [201] Midi Port Address [330]...
-
Page 60: Power Management Setup
ECP Mode Use DMA (3) When the onboard parallel port is set to ECP mode, the parallel port can use DMA 3 or DMA 1. Press <Esc> to return to the Integrated Peripherals screen. Init Display First (PCI Slot) Use this item to specify whether your graphics adapter is installed in one of the PCI slots or is integrated on the mainboard. - Page 61 Phoenix – AwardBIOS CMOS Setup Utility Power Management Setup Item Help ACPI function [Enabled] Power Management Option [User Define] Menu Level HDD Power Down [Disable] Suspend Mode [Disable] Video Off Option [Suspend --> Off] Video Off Method [DPMS Support] MODEM Use IRQ Soft-Off by PWRBTN [Instant-Off] IRQ/Event Activity Detect...
- Page 62 If you want an incoming call on a modem to automatically resume the system from a power-saving mode, use this item to specify the interrupt request line (IRQ) that is used by the modem. You might have to connect the fax/modem to the mainboard Wake On Modem connector for this feature to work.
- Page 63 VGA (Off) When set to On, the system power will resume the system from a power sav- ing mode if there is any VGA activity. LPT & COM (LPT/COM ) When this item is enabled, the system will restart the power-saving timeout counters when any activity is detected on the serial ports, or the parallel port.
-
Page 64: Pnp/Pci Configurations
↑ ↑ ↑ ↑ ↓ ↓ ↓ ↓ → → → → ← ← ← ← : Move Enter : Select +/-/PU/PD:Value: F10: Save ESC: Exit F1:General Help F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults This screen enables you to set IRQs that will resume the system from a power saving mode. - Page 65 PNP OS Installed [No] Item Help Reset Configuration Data [Disabled] Menu Level Resources Controlled by [Auto(ESCD)] x IRQ Resources Press Enter Default is Disabled. Select Enabled to PCI/VGA Palette Snoop [Disabled] reset Extended Assign IRQ For VGA [Enabled] System Configuration Assign IRQ For USB [Enabled] Data (ESCD) when you...
-
Page 66: Pc Health Status
Assign IRQ for VGA/USB (Enabled) Names the interrupt request (IRQ) line assigned to the USB/VGA (if any) on your system. Activity of the selected IRQ always awakens the system. PC Health Status On mainboards that support hardware monitoring, this item lets you monitor the parameters for critical voltages, critical temperatures, and fan speeds. -
Page 67: Load Fail-Safe Defaults Option
Item Help CPU Voltage Regulator [Normal] Auto Detect DIMM/PCI Clk [Enabled] Menu Level Spread Spectrum Modulated [Enabled] CPU Host/PCI Clock [Default] ↑ ↑ ↑ ↑ ↓ ↓ ↓ ↓ → → → → ← ← ← ← : Move Enter : Select +/-/PU/PD:Value: F10: Save ESC: Exit F1:General Help... -
Page 68: Load Optimized Defaults Option
Load Optimized Defaults Option This option opens a dialog box that lets you install optimized defaults for all appropriate items in the Setup Utility. Press <Y> and then <Enter> to install the defaults. Press <N> and then <Enter> to not install the defaults. The opti- mized defaults place demands on the system that may be greater than the performance level of the components, such as the CPU and the memory. - Page 69 ing dialog box appears, press <Y> to discard changes and exit, or press <N> to return to the main menu. Note: If you have made settings that you do not want to save, use the "Exit Without Saving" item and press <Y> to discard any changes you have made.
-
Page 70: Using The Mainboard Software
Chapter 4 Chapter 4 Using the Mainboard Software About the Software CD-ROM About the Software CD-ROM The support software CD-ROM that is included in the mainboard package contains all the drivers and utility programs needed to properly run the bun- dled products. -
Page 71: Running Setup
Setup Tab Setup Click the Setup button to run the software installation program. Select from the menu which software you want to install. Browse The Browse CD button is the standard Windows command that allows you to open Windows Explorer and show the contents of the support CD. - Page 72 Note: The following screens are examples only. The screens and driver lists will be different according to the mainboard you are installing. The mainboard identification is located in the upper left-hand corner. Click Next. The following screen appears: Check the box next to the items you want to install. The default options are recommended.
-
Page 73: Manual Installation
Manual Installation Manual Installation Insert the CD in the CD-ROM drive and locate the PATH.DOC file in the root directory. This file contains the information needed to locate the drivers for your mainboard. Look for the chipset and mainboard model; then browse to the directory and path to begin installing the drivers. - Page 74 We strongly recommend users to install this free anti-virus software to help protect your system against viruses. MediaRing Talk – Telephony Software To install the MediaRing Talk voice modem software for the built-in modem, go directory \UTILITY\MEDIARING TALK, then MRTALK- SETUP72.EXE to install the application software.