1. Manuals
  2. Brands
  3. Sony Manuals
  4. Stereo System
  5. HCD-V8800
  6. Service manual

Sony HCD-V8800 Service Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

SERVICE MANUAL
HCD-V8800 is the tuner, deck, Video CD and
amplifier section in LBT-V8800AV.
MICROFILM
HCD-V8800
Model Name Using Similar Mechanism
CD
CD Mechanism Type
SECTION
Base Unit Type
Optical Pick-up Type
TAPE
Model Name Using Similar Mechanism
DECK
Tape Transport Mechanism Type
SECTION
SPECIFICATIONS
COMPACT DISC DECK RECEIVER
— 1 —
E Model
Chinese Model
HCD-V4500
CDM37L-5BD21AL
BU-5BD21AL
KSS-213D/Q-NP
HCD-V4500
TCM-220WR2
— Continued on next page —

Advertisement

Table of Contents
loading

Related Manuals for Sony HCD-V8800

Summary of Contents for Sony HCD-V8800

  • Page 1 HCD-V8800 SERVICE MANUAL E Model Chinese Model HCD-V8800 is the tuner, deck, Video CD and amplifier section in LBT-V8800AV. Model Name Using Similar Mechanism HCD-V4500 CD Mechanism Type CDM37L-5BD21AL SECTION Base Unit Type BU-5BD21AL Optical Pick-up Type KSS-213D/Q-NP TAPE Model Name Using Similar Mechanism...
  • Page 2 WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. — 2 —...

  • Page 3: Table Of Contents

    TABLE OF CONTENTS NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT 1. SERVICING NOTE ............4 The laser diode in the optical pick-up block may suffer electrostatic 2. GENERAL break-down because of the potential difference generated by the ................

  • Page 4: Servicing Note

    SECTION 1 SERVICING NOTE MC Cold Reset 3. Press POWER button to turn the set OFF. 4. Press ENTER/NEXT and POWER buttons simultaneously, • The cold reset clears all data including preset data stored in the RAM to initial conditions. Execute this mode when returning the and the display of fluorescent indicator tube changes to “AM set to the customer.
  • Page 5 SELF-DIAGNOSIS 2. Aging Mode in Tape Deck Section 2-1. Operating procedure of Aging Mode This model has the self-diagnosis function for the VIDEO and 1. Load a commercially available 10-minute tape into the decks AUDIO decoder sections. A and B respectively. Immediately after the power on, the self-diagnosis function searches (If a 10-minute tape is not available, another tape may be each operation of IC’s around the mechanism control microcom-...

  • Page 6: General

    SECTION 2 GENERAL Front Panel !∞ !¢ !£ !™ !¡ !§ !¶ !• @º @¡ !ª #¶ @™ #§ @£ @¢ #∞ @∞ #¢ #£ #¡ #º @ª @• @¶ @§ #™ #• %¡ #ª %º $º $ª $¡ $• $™...

  • Page 7: Disassembly

    LOCATION OF PARTS AND CONTROLS 1 POWER button @∞ SUPER W MODE button $ª DIRECTION button @§ GEQ control buttons %º Deck A p button 2 DISPLAY/DEMO button 3 SPECTRUM ANALYZER button @¶ GEQ CONTROL button %¡ Deck A ª, · button 4 Display Window @•...

  • Page 8: Main Board

    3-2. MAIN BOARD Installing the power cord for the Chinese model. 5 Back panel 3 Seven screws (BVTP3x8) Power transformer 4 Power cord 2 Eleven screws 9 Connector Bushing cord (BVTP3x8) (CN601) 0 Connector 1 Flat type wire (CN1) (CN9001) Ferrite core Wire clamp !£...

  • Page 9: Cassette Lid Assembly

    3-4. CASSETTE LID ASSEMBLY 3 Two bracket 2 Two screws (BVTP2.6x8) 1 Two springs 4 Cassette lid assembly 3-5. CD LID ASSEMBLY 1 Four screws (BVTP2.6x8) 2 Connector (CN671) 4 CD lid assembly 3 Connector (CN661) — 9 —...

  • Page 10: Cd Mechanism Deck

    3-6. CD MECHANISM DECK 3-7. BASE UNIT 1 Five screws (BVTP3x8) 3 Flat type wire 2 CD mechanism deck 3 Base unit 2 Boss 1 Yoke bracket 3-8. DISC TABLE Note: When the disc table is installed, adjust the positions of roller cam and mark ”...

  • Page 11: Test Mode

    SECTION 4 TEST MODE VIDEO CD COLOR-BARS MODE [VIDEO BOARD] (SIDE B) On this mode, the data of the color-bars signal as a picture signal and the 1kHz sine wave signal as a sound signal are output by the mechanism control microcomputer (IC701) for video CD signal SL703 (AFADJ) check.

  • Page 12: Mechanical Adjustments

    SECTION 5 SECTION 6 MECHANICAL ADJUSTMENTS ELECTRICAL ADJUSTMENTS Precaution DECK SECTION 0 dB=0.775V 1. Clean the following parts with a denatured alcohol-moistened swab: 1. Demagnetize the record/playback head with a head damagnetizer. record/playback heads pinch rollers 2. Do not use a magnetized screwdriver for the adjustments. erase head rubber belts 3.
  • Page 13 2. Turn the adjustment screw and check output peaks. If the peaks Tape Speed Adjustment (Deck A) do not match for L-CH and R-CH, turn the adjustment screw so that outputs match within 1 dB of peak. Note: Set the test mode using the following method and begin tape speed adjustment.
  • Page 14 Record Bias Adjustment (Deck B) Record Level Adjustment (Deck B) Procedure: Procedure: INTRODUCTION INTRODUCTION When set to the test mode performed in Tape Speed Adjust- When set to the test mode performed in Tape Speed Adjust- ment, when the tape is rewound after recording, the “REC memory ment, when the tape is rewound after recording, the “REC memory mode”...
  • Page 15 CD SECTION Note : A clear RF signal waveform means that the shape “◊” can be clearly distinguished at the center of the waveform. NOTE : RF signal waveform 1. CD Block is basically designed to operate without adjustment. Therefore, check each item in order given. VOLT/DIV : 200mV 2.
  • Page 16 RF PLL Free-run Frequency Check VIDEO SECTION Procedure : 1. Connect frequency counter to TP (PLCK) with lead wire. Frequency adjustment frequency counter 1. Connect the frequency counter to check point of the VIDEO BD board board. TP (PLCK) frequency counter –...

  • Page 17: Diagrams

    SECTION 7 DIAGRAMS 7-1. CIRCUIT BOARDS LOCATION TRANS board VIDEO POWER board FM/AM TUNER PACK PANEL board HP/MIC board SURROUND board TC-A SW board MAIN board CD-LED board CD-A SW board KEY CON board VIDEO OUT board DOOR SW board VIDEO board POWER board TC-B SW board...

  • Page 18: Block Diagrams

    HCD-V8800 7-2. BLOCK DIAGRAMS — KEY CON SECTION — MIC AMP ECHO AMP IC760 (1/2) IC760 (2/2) J761 MIC 1 RV760 MIC LEVEL ECHO IC761 J762 MIC 2 RV761 LPF1 LPF2 ECHO LEVEL SWITCH IC1403 L IN 9 10 11...

  • Page 19: Cd Section

    HCD-V8800 — CD SECTION — OPTICAL PICK-UP BLOCK (KSS-213D/Q-NP) DIGITAL SERVO RF AMP DIGITAL SIGNAL PROCESSOR LASER IC103 IC101 DIODE POWER APC LD LDON PRIORITY EMCODER 384FS DRIVE ADDRESS DOUT CLOCK Q101 DIGITAL GENERATOR EXCK GENERATOR SUBCODE SBSO PROCESSOR ASY0...

  • Page 20: Video Section

    HCD-V8800 — VIDEO SECTION — 10BIT VIDEO D/A CONVERTER IC401 MPEG DECODER NOISE REDUCTION VIDEO AMP IC201 IC301 J9001 IC451 VIDEO OUT BUFFER IC501 (1/2) Y0-Y7 Y, C/Y, U, V • • • SELECTOR VIDEO DEMPX, LEVEL MODULATOR MPEG MPEG &...

  • Page 21: Deck Section

    HCD-V8800 — DECK SECTION — PB A/B S1008 S1004 B CrO A CrO CN403 R CH RV311 PLAYBACK IC611 A 120/70 LEVEL PB-A/B B 120/70 DECK A A IN PB OUT B IN PB L HP101 PB HEAD R CH...

  • Page 22: Main Section

    HCD-V8800 — MAIN SECTION — VOLUME DOLBY PRO LOGIC IC604 DELAY IC601 CENTER REAR KEY CON IC602 IC603 MUTE REAR L IN SECTION C-OUT REAR REAR Q602 DATA L-IN S-OUT S-OUT S-IN L-IN L-OUT FRONT LATCH DATA FRONT L-MIX CENTER...

  • Page 23: Power Section

    HCD-V8800 — POWER SECTION — TM402 SURROUND POWER AMP SPEAKER IC601 RY401 REAR REAR –1 REAR REAR CENTER –2 CENTER CENTER CENTER RELAY DRIVE Q404 FAN MOTOR M901 DRIVER UNREG Q961, 962 MOTOR –12V OVER LOAD Q601,651 THERMAL TM401 POWER AMP...

  • Page 24: Ic Block Diagrams

    7-19. IC BLOCK DIAGRAMS • BD section IC101 CXD2545Q 67 62 63 64 20 19 32K RAM CLOCK GENERATOR C16M 43 PSSL ADDRESS PRIORITY DIGITAL VCO1 SERIAL GENERATOR ENCODER VCO0 PARALLEL DEMODULATOR VARI-PITCH 61-46 DA01-16 DOUBLE SPEED PROCESSOR FILI FILO 79 MUTE SYNC CLTV...
  • Page 25 • Video section IC101 CXD8567AM INIT D Vdd 2 SYSM L1 (+) A Vdd L SHIFT L2 (+) LATCH A Vss L 256FSO X Vss TEST1 512IN D Vss X OUT MCKSEL X Vdd XBCK A Vss R DATA R2 (+) LRCK A Vdd R MUTE L...
  • Page 26 IC271 BU6257AFV 16 15 14 13 12 CHARACTER HORIZONTAL WRITE SIZE ADDRESS ADDRESS REGISTER REGISTER COUNTER CHARACTER DATA HORIZONTAL HORIZONTAL HORIZONTAL 3 BIT × 288 WORD SIZE POSITION ADDRESS COUNTER COUNTER COUNTER COLOR DATA 3 BIT × 288 WORD VERTICAL CHARACTER DATA 8 BIT ×...
  • Page 27 IC401 CXD1913Q 50 49 48 46 45 44 43 42 41 40 37-39 36 35 34 33 XTEST4 BURST FLAG CSYNC SYNC Gen. SYNC Slope Gen. XRST Sub Carrier Timing Controller TEST MODE Gen. SYSCLK PDCLK SIO and I O-Bus Closed Caption Encoder VSYNC (for NTSC)
  • Page 28 IC601 LA2786 BPF1 NOISE NOISE FILTER BPF2 NOISE GENERATOR DATA BALANCE ENABLE VREF V REF CONTROL OSC1 DIVIDER CONTROL S-CH DC OUT C-CH DC OUT L-CH DC OUT R-CH DC OUT VREF L-IN L-OUT R-IN R-OUT S-OUT C-OUT CMODE-CAP. C-TRIM DC CUT R-BPF1 L-BPF1 L-BPF2...

  • Page 29: Panel Section

    IC602 LV1016 INV-PHASE ADM-CONT SRAM L+DELAY R+DELAY VOL/MUTE OUT-FILTER – DC-OUT IN-FILTER (7k/5k) (40kHz) L–R S-TRIM (–6dB) B-NR • Deck section IC402 LB1641 IC602 uPC1330HA T.S.D O.C.P INVERTER MOTOR MOTOR DRIVE DRIVE COMPARATER SW P1 CONT GND SW P2 GND SW R1 GND SW R2 FWD/REV/STOP...
  • Page 30 • CD motor section IC201 TA8409S VREF BLOCK STANDBY BLOCK HEAT CUT OFF BLOCK OUT2 OUT1 VREF • KEY CON section IC1401 M65847FP – – – – LPF1 LPF2 CLOCK RESET GENERATOR LOGIC IC1403 MC14053BCP B.COM OPEN A.COM C.COM OPEN OPEN —...

  • Page 31: Ic Pin Functions

    7-20. IC PIN FUNCTIONS • IC101 DIGITAL SIGNAL PROCESSOR (CXD2545Q)/BD board Function Pin No. Pin Name Sled drive output (Not used) SRON Sled drive output SRDR Sled drive output (Not used) SFON Tracking drive output TFDR Tracking drive output (Not used) TRON Tracking drive output TRDR...
  • Page 32 Pin No. Function Pin Name DA 11 output when PSSL=1. GTOP output when PSSL=0 (Not used) GTOP DA 10 output when PSSL=1. XUGF output when PSSL=0 (Not used) XUGF DA 09 output when PSSL=1. XPLCK output when PSSL=0 XPLCK DA 08 output when PSSL=1. GFS output when PSSL=0 DA 07 output when PSSL=1.
  • Page 33 • IC201 MPEG DECODER (CXD1852AQ)/VIDEO board Pin No. Function Pin Name – Ground Video decoder master clock pin. Input the XTL0I clock or connect an oscillator between XTL0O XTL0I and XTL0O. The recommended frequencies are 27MHz, 28.6363MHz (NTSC XTL0I 8fsc), and 35.4686 MHz (PAL 8fsc). –...
  • Page 34 Pin Name Function Pin No. Data input/output signal pin. Connect to the DRAM data pin so that the lower and upper bytes of the data correspond to the CAS0 to CAS3 controls. MD10 – +5V power supply – Ground MD11 MD12 Data input/output signal pin.
  • Page 35 Pin Name Pin No. Function B/Cb0 B/Cb1 B/Cb2 Output pin of the B or Cb signal of the image data. MSB is B/Cb7. Synchronizes with B/Cb3 DCLK. (Not used) B/Cb4 B/Cb5 B/Cb6 B/Cb7 Dot clock (DCLK) signal pin. The DCLK frequency is normally 13.5MHz. The DCLK can be input from this pin or can be made by frequency-dividing (1/integer) the clock input DCLK from XTL0I.
  • Page 36 Pin No. Pin Name Function Serial data input (CXD2545Q) DATI Bit clock input (CXD2545Q) BCKI Digital input signal (Not used) DOIN Register access chip select signal pin. XHCS Data acknowledge/wait signal pin for DMA transmission, register access, transparent XHDT memory access. Register access control signal pin.
  • Page 37 • IC301 NOISE REDUCTION (CXD1854Q)/VIDEO board Pin No. Pin Name Function Ground – [MSB] B input 0–7 (Connect to ground) [LSB] – Ground Y/GI7 [MSB] Y/GI6 Y/GI5 Y/GI4 G (Y) input 0–7 Y/GI3 Y/GI2 Y/GI1 [LSB] Y/GI0 – Ground C/RI7 [MSB] C/RI6 C/RI5...
  • Page 38 Function Pin No. Pin Name [MSB] C/RO0 C/RO1 C/RO2 C/RO3 R (Cb/Cr) output 0–7 C/RO4 C/RO5 C/RO6 [LSB] C/RO7 Power supply (+5V) – Y/GO7 [MSB] Y/GO6 Y/GO5 Y/GO4 G (Y) output 0–7 Y/GO3 Y/GO2 Y/GO1 Y/GO0 [LSB] – Power supply (+5V) [MSB] B output 0–7 (Not used) [LSB]...
  • Page 39 • IC401 10 BIT VIDEO D/A CONVERTER (CXD1913Q)/VIDEO board Pin No. Pin Name Function 8-bit pixel data input pins (PD0 to 7). When control register bit “PIF MODE”=“0”, serve as input pins for multiplexed Y, Cb, Cr signals. When control register bit “PIF MODE”=“1”, serve as input pins for Y signal –...
  • Page 40 Digital ground The functions of this pin are selected by Pin 64 XIICEN. When the XIICEN pin is “H”, sets into the SONY SIO mode, and becomes the SI serial data input pin. When the XIICEN pin is “L”, sets into the I...
  • Page 41 HSYNC The functions of this pin are selected by Pin 64 XIICEN. When the XIICEN pin is “H”, sets into the SONY SIO mode, and becomes the S0 serial- out output pin. When the XIICEN pin is “L”, this pin is not used and sets into high impedance (Not used) Field ID output.
  • Page 42 • IC701 MECHANISM CONTROL (HD6433032SK12F)/VIDEO board Pin No. Function Pin Name Input/output terminal exchanging data bus 0 with IIC interface (IC901) CMD0 Input/output terminal exchanging data bus 1 with IIC interface (IC901) CMD1 Input/output terminal exchanging data bus 2 with IIC interface (IC901) CMD2 Input/output terminal exchanging data bus 3 with IIC interface (IC901) CMD3...
  • Page 43 Pin No. Pin Name Function – A/D converter (Pin62-29) power supply (Connected to +5V) Check LED control (Error : flashing) CHECK-LED XHIRQ Interruption request input from MPEG decoder Subcode sync input (CXD2545Q) SCOR MREQ Inputs command request from IIC interface (IC901) DATA Serial data output Mute output (“H”...
  • Page 44 • IC901 IIC INTERFACE (uPD780016YGF-012-3BA)/VIDEO board Pin No. Pin Name Function Connected to ground P80 to P87 1 to 8 TEST Connected to ground – X’ tall (5MHz) X’ tall (5MHz) Power supply +5V – Not used – Connected to +5V –...
  • Page 45 • IC701 MASTER CONTROL (uPD780016YGF-019-3BA)/MAIN board Pin Name Function Pin No. TA-MUTE Line mute signal outputA DBFB-H/L DBFB H/L select signal output 427-LT Latch signal output for IC201 (62427) KCON-LT Latch signal output for key control KCON-ON Key control ON/OFF signal output F-RELAY Front speaker relay control output (Not used) R-RELAY...
  • Page 46 Pin No. Pin Name Function MSM-LT MSM-NAR Not used MSM-CH INPUT-CHANGE Input sensitivity switching output IIC-DATA Data output for IC601, 901 IIC-CLK Clock output for IC601, 901 XRST CD reset signal output CD latch signal output (Not used) FOUCUS-SW Not used TBL-L Table motor control output TBL-R...
  • Page 47 • IC601 DISPLAY CONTROL (TMP87CM75-6565)/PANEL board Pin Name Function Pin No. SEG35 FL segment signal output VLOAD Power supply (–25V) for FL segment signal output 3 to 10 LED1 to LED8 LED driver output – Ground X-OUT X’tall (8MHz) X-IN RESET Reset signal input from main controller LED 9...

  • Page 48: Exploded Views

    SECTION 8 EXPLODED VIEWS NOTE: The components identified by mark ! • Items marked “*” are not stocked since they are • Abbreviation or dotted line with mark ! are critical seldom required for routine service. Some delay : Singapore model for safety.

  • Page 49: Front Panel Section 1

    8-2. FRONT PANEL SECTION 1 TCM-220WR2 not supplied not supplied not supplied not supplied not supplied not supplied Supplied with S711 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-987-995-01 SPRINAG (CD EJECT), COMPRESSION * 65 4-987-933-01 BRACKET (TA) 4-987-001-01 BUTTON (EJECT CD) * 53...

  • Page 50: Front Panel Section 2

    4-987-013-01 INDICATOR (TUNER) 4-987-021-01 INDICATOR (TC A) X-4947-968-1 BUTTON (WOOFER) ASSY 4-986-997-01 BUTTON (DECK.A) X-4947-967-1 BUTTON (DECK B) ASSY 4-963-404-21 EMBLEM (5-A), SONY 4-987-022-01 INDICATOR (TC B) 4-973-644-01 KNOB (MIC) 4-951-620-01 SCREW (2.6X8), +BVTP 4-987-996-01 SPRING (TC LID), TENSION 4-948-236-01 CUSHION (107)

  • Page 51: Chassis Section

    8-4. CHASSIS SECTION not supplied CNP901 T501 (IA) (CH) (IA, CH) (E, SP, MY) CNP901 not supplied (E, SP, MY) not supplied CDM37L-5BD21AL not supplied The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number speci- not supplied fied.

  • Page 52: Tc Mechanism Section-1 (Tcm-220Wr2)

    8-5. TC MECHANISM SECTION-1 (TCM-220WR2) not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark X-4947-943-1 HOLDER (L) ASSY, CASSETTE * 206 4-980-439-01 FULCLUM, HOLDER X-4947-944-1 HOLDER (R) ASSY, CASSETTE 3-354-957-01 JOINT (LOCK LEVER) 4-959-231-11 SPRING (L), TORSION 3-354-953-01 LEVER (LOCK LEVER L) 4-959-232-11 SPRING (R), TORSION 3-354-954-01 LEVER (LOCK LEVER R)

  • Page 53: Tc Mechanism Section-2 (Tcm-220Wr2)

    8-6. TC MECHANISM SECTION-2 (TCM-220WR2) (including p A) not supplied HP101 (including r A) 262 274 not supplied not supplied HRPE101 (including r B) not supplied not supplied not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No.

  • Page 54: Tc Mechanism Section-3 (Tcm-220Wr2)

    8-7. TC MECHANISM SECTION-3 (TCM-220WR2) pA: MOTOR board (Suppplied with AUDIO board) not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-908-600-01 LEVER (REV-B) 3-908-597-01 CAM (A) 3-908-608-11 SCREW, STEP * 316 1-650-669-11 LEAF SWITCH BOARD X-3372-930-3 ARM (A) ASSY, FR 3-908-598-01 CAM (B) X-3370-169-1 FLYWHEEL (AR) ASSY...

  • Page 55: Cd Mechanism Section (Cdm37L-5Bd21Al)

    8-8. CD MECHANISM SECTION (CDM37L-5BD21AL) M201 supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-987-976-01 SCREW, STEP 4-978-426-01 INDICATOR (NO.) 4-944-490-01 BELT (TIMING) A-4660-978-A GEAR (PULLEY) ASSY * 366 1-659-059-13 LED BOARD 4-978-421-01 GEAR (MID) * 367 1-659-058-13 TABLE SENSOR BOARD 4-978-425-01 ROLLER (CAM)

  • Page 56: Base Unit Section (Bu-5Bd21Al)

    8-9. BASE UNIT SECTION (BU-5BD21AL) M101 M102 The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number speci- fied. Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark ! 401...

  • Page 57: Electrical Parts List

    SECTION 9 AUDIO ELECTRICAL PARTS LIST Note: • SEMICONDUCTORS • Due to standardization, replacements in the parts list The components identified by mark ! In each case, u: µ , for example: may be different from the parts specified in the or dotted line with mark ! are critical uA...: µ...
  • Page 58 AUDIO Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R601 1-249-409-11 CARBON 1/4W F C156 1-163-237-11 CERAMIC CHIP 27PF R602 1-249-409-11 CARBON 1/4W F C157 1-163-145-00 CERAMIC CHIP 0.0015uF 5% R608 1-249-409-11 CARBON 1/4W F C159 1-163-019-00 CERAMIC CHIP 0.0068uF 10% R609...
  • Page 59 CD-B2 SW CD-LED CD MOTOR CD-A SW CD-B1 SW Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R162 1-216-101-00 METAL CHIP 150K 1/10W < RESISTOR > < SWITCH > R745 1-247-815-91 CARBON 1/4W R746 1-249-411-11 CARBON 1/4W S101 1-572-085-11 SWITCH, LEAF (LIMIT)
  • Page 60 CD MOTOR DOOR SW HP/MIC Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < CAPACITOR > C773 1-126-964-11 ELECT 10uF C774 1-126-964-11 ELECT 10uF C201 1-124-907-11 ELECT 10uF C775 1-162-294-31 CERAMIC 0.001uF C202 1-164-159-21 CERAMIC 0.1uF C203 1-124-907-11 ELECT 10uF...
  • Page 61 HP/MIC KEY CON LEAF SWITCH Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R769 1-247-885-00 CARBON 180K 1/4W < TRANSISTOR > R770 1-247-807-31 CARBON 1/4W Q1401 8-729-900-80 TRANSISTOR DTC114ES Q1403 8-729-119-78 TRANSISTOR 2SC2785-HFE R771 1-247-863-91 CARBON 1/4W R772 1-247-863-91 CARBON...
  • Page 62 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-659-059-13 LED BOARD C213 1-136-171-00 FILM 0.33uF C214 1-126-964-11 ELECT 10uF ********* < DIODE > C215 1-136-153-00 FILM 0.01uF C230 1-136-167-00 FILM 0.15uF D201 8-719-032-98 DIODE SEL5820A (DISC No.) C231 1-130-471-00 MYLAR 0.001uF...
  • Page 63 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C606 1-136-167-00 FILM 0.15uF C667 1-126-964-11 ELECT 10uF C668 1-162-286-21 CERAMIC 220PF C607 1-126-963-11 ELECT 4.7uF C608 1-126-963-11 ELECT 4.7uF C669 1-109-889-11 ELECT C609 1-136-173-00 FILM 0.47uF C678 1-162-294-31 CERAMIC 0.001uF...
  • Page 64 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark D799 8-719-987-63 DIODE 1N4148M Q201 8-729-119-78 TRANSISTOR 2SC2785-HFE D901 8-719-025-23 DIODE RBA-402-SL Q202 8-729-119-78 TRANSISTOR 2SC2785-HFE D902 8-719-200-82 DIODE 11ES2 Q206 8-729-900-36 TRANSISTOR DTC124ES Q251 8-729-119-78 TRANSISTOR 2SC2785-HFE D903 8-719-200-82 DIODE 11ES2 Q252...
  • Page 65 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R179 1-249-429-11 CARBON 1/4W R358 1-249-421-11 CARBON 2.2K 1/4W F R202 1-249-425-11 CARBON 4.7K 1/4W F R359 1-249-428-11 CARBON 8.2K 1/4W F R401 1-249-425-11 CARBON 4.7K 1/4W F R203 1-249-437-11 CARBON 1/4W...
  • Page 66 MAIN PANEL Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R726 1-247-807-31 CARBON 1/4W R961 1-249-421-11 CARBON 2.2K 1/4W F R727 1-247-807-31 CARBON 1/4W R962 1-249-432-11 CARBON 1/4W R963 1-249-425-11 CARBON 4.7K 1/4W F R728 1-247-807-31 CARBON 1/4W R730 1-249-431-11 CARBON...
  • Page 67 PANEL Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C690 1-164-159-21 CERAMIC 0.1uF < TRANSISTOR > (EXCEPT MY) C693 1-164-159-21 CERAMIC 0.1uF Q601 8-729-119-78 TRANSISTOR 2SC2785-HFE Q602 8-729-118-00 TRANSISTOR 2SB1116-L (EXCEPT MY) Q603 8-729-118-00 TRANSISTOR 2SB1116-L C695 1-164-159-21 CERAMIC 0.1uF...
  • Page 68 PANEL POWER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R643 1-249-403-11 CARBON 1/4W F R701 1-247-807-31 CARBON 1/4W R702 1-247-807-31 CARBON 1/4W R644 1-247-807-31 CARBON 1/4W R703 1-247-807-31 CARBON 1/4W R704 1-247-807-31 CARBON 1/4W R645 1-249-407-11 CARBON 1/4W F R646...
  • Page 69 POWER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C107 1-128-576-11 ELECT 100uF < DIODE > C108 1-128-563-11 ELECT 100uF 100V C110 1-104-665-11 ELECT 100uF D101 8-719-510-68 DIODE D5SBA20F01 C151 1-128-493-11 ELECT 4700uF D102 8-719-025-03 DIODE RBA-402-SL D104 8-719-200-82 DIODE 11ES2 C152...

  • Page 70: Power Surround

    POWER SURROUND Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < RESISTOR > R408 1-249-437-11 CARBON 1/4W R409 1-249-440-11 CARBON 1/4W ! R101 1-219-122-91 FUSIBLE 0.33 1/4W F R410 1-249-437-11 CARBON 1/4W R411 1-249-437-11 CARBON 1/4W R201 1-249-417-11 CARBON 1/4W F...
  • Page 71 SURROUND TABLE SENSOR TC-A SW Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C651 1-126-963-11 ELECT 4.7uF R654 1-249-437-11 CARBON 1/4W R655 1-260-103-11 CARBON 2.2K 1/2W C652 1-162-292-31 CERAMIC 680PF R656 1-260-103-11 CARBON 2.2K 1/2W C653 1-162-286-21 CERAMIC 220PF C654...
  • Page 72 TC-A SW TC-B SW TRANS VIDEO Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark S647 1-554-303-21 SWITCH, TACTILE (DIRECTION) < SWITCH > ! S501 1-762-753-11 SWITCH, VOLTAGE SELECTION ************************************************************** (VOLTAGE SELECTOR)(E,SP,IA,CH) 1-664-013-11 TC-B SW BOARD < TRANSFORMER > ************* <...
  • Page 73 VIDEO Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C273 1-163-038-91 CERAMIC CHIP 0.1uF C903 1-163-038-91 CERAMIC CHIP 0.1uF C274 1-163-141-00 CERAMIC CHIP 0.001uF C904 1-163-038-91 CERAMIC CHIP 0.1uF C275 1-163-038-91 CERAMIC CHIP 0.1uF C276 1-163-243-11 CERAMIC CHIP 47PF C908 1-163-038-91 CERAMIC CHIP...
  • Page 74 VIDEO Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < COIL > R220 1-216-073-00 METAL CHIP 1/10W L101 1-410-377-31 INDUCTOR CHIP 4.7uH R221 1-216-073-00 METAL CHIP 1/10W L251 1-410-377-31 INDUCTOR CHIP 4.7uH R222 1-216-073-00 METAL CHIP 1/10W R223 1-216-073-00 METAL CHIP...
  • Page 75 VIDEO VIDEO OUT VIDEO POWER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R461 1-216-295-91 CONDUCTOR, CHIP (2012) R912 1-216-073-00 METAL CHIP 1/10W R462 1-216-295-91 CONDUCTOR, CHIP (2012) R463 1-216-295-91 CONDUCTOR, CHIP (2012) R913 1-216-073-00 METAL CHIP 1/10W R464 1-216-097-91 METAL GLAZE...
  • Page 76 VIDEO POWER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C9004 1-126-964-11 ELECT 10uF ACCESSORIES & PACKING MATERIALS C9005 1-126-935-11 ELECT 470uF 6.3V ******************************* 1-475-166-11 COMMANDER, STANDARD (RM-SV909) C9006 1-126-933-11 ELECT 100uF 1-501-374-11 ANTENNA, LOOP (IA) <...
  • Page 77 HCD-V8800 Sony Corporation 97G0922-1 Printed in Japan © 1997. 7 9-920-932-11 Home A&V Products Company Published by General Engineering Dept. (SP) (Shibaura) — 126 —...

Table of Contents