Terminal Function Of Ics - Panasonic SA-XH70PH Service Manual

19.3. Terminal Function of ICs

19.3.1. IC200 (RFKWMXH70EB): IC MICRO-
PROCESSOR
Pin No. Terminal Name I/O
1 CLOSE_SW I
2 ECO_CONTRL O Control Voltage Supply of D-AMP for
3 RMT I
4 NC -
5 NC -
6 BYTE -
7 CNVSS -
8 NC -
9 NC -
10 RESET I
11 XOUT O Clock Out
12 VSS -
13 XIN I
14 VCC -
15 CEC_IN/OUT I/O CEC I/O
16 TUN_INT O Tuner Interrupt Requset
17 SYNC I
18 NC -
19 NC -
20 TUN_SDIO I/O Tuner I2C (Software) Data
21 TUN_RST I
22 TUN_SCLK O Tuner Serial Clock
23 LED_CTRL O Power On LED control
24 FLD_OUT O FL Display Data Out Signal
25 FLD_CLK O FL Display Clock Signal
26 FLD_STB O FL Display Strobe Signal
27 DVD_RX I
28 DVD_TX O DVD UART Transmit
29 DBG_TX I
30 DBG_RX O UART RX for Debug
31 SCLK O Clock Signal for Flash Writing
32 DAP_MUTE O Master mute for DAP
33 EDA O I2C EEPROM data
34 ECK O I2C EEPROM clock
35 NC -
36 FWD O Forward control for mechanism
37 REV O Reverse control for mechanism
38 AMUTE O Audio Muting
39 EPM -
40 NC -
41 NC -
42 NC -
43 NC -
44 CE I
45 NC -
46 NC -
47 NC -
48 PCONT O System Power Control
49 RGB_H I/O Blanking Signal for SCART
50 VMUTE O Video Muting
51 VBUS_EN O USB Vbus Supply Enable
52 USB_OC O USB Over-Current Protection
53 NC -
54 NC -
55 DCDET1 I
56 DCDET2 I
57 NC -
Function
Close Switch for Mechanism
Eco Mode
Remote Control Signal
No Connection
No Connection
External data bus width select input
Micon Programming-Processor / Sin-
gle Chip Mode
No Connection
No Connection
Microp Reset Signal
GND
Clock In
VCC +3.3V
AC Sync Signal
No Connection
No Connection
Tuner Reset Signal
DVD UART Receive
UART TX for Debug
No Connection
For Downloading Purpose
No Connection
No Connection
No Connection
No Connection
For Downloading Purpose (with pull
up)
No Connection
No Connection
No Connection
No Connection
No Connection
Power Supply Failure Detection (F76)
D-Amp and Fan Failure Detection
(F61)
No Connection
Pin No. Terminal Name I/O
58 NC
59 NC
60 VCC
61 NC
62 VSS
63 NC
64 NRST
65 NC
66 WIDE1
67 NC
68 NC
69 NC
70 NC
71 NC
72 NC
73 VOL 0
74 NC
75 DAP_DAT
76 DAP_CLK
77 NC
78 NC
79 DAP_RST
80 DAP_PDN
81 VALID
82 SD
83 OTW
84 NC
85 NC
86 DES 3
87 NC
88 AUX_DET
89 KEY 2
90 KEY1
91 SEL_A
92 SEL_B
93 DES2
94 AVSS
95 DES1
96 VREF
97 AVCC
98 NC
99 SPDIF_SW
100 OPEN_SW
115
Function
- No Connection
- No Connection
- +3.3V System Supply
- No Connection
- System Ground
- No Connection
O ADC Reset
- No Connection
O Signal to control SCART 16:9 or 4:3
- No Connection
- No Connection
- No Connection
- No Connection
- No Connection
- No Connection
O For Energy Star (FL Power Control)
- No Connection
O DAP/DSP data
O DAP/DSP clock
- No Connection
- No Connection
O DAP Reset
O DAP Power Down Control
O DAP valid
I D-AMP Shutdown Signal
I D-AMP Over Temperature Warning
- No Connection
- No Connection
I Model Series 2
- No connection
I Fan analog to digital control
I Keyline 2:
I Keyline 1: 1st key is POWER During
STOP mode; act as KI0 After wake
up; act as AN4
I Analog Input Selector Control A
I Analog Input Selector Control B
- Model Selector
- Analog GND
- Model Number
- Voltage Reference +3.3V
- Analog +3.3V Supply
- No Connection
O Selector control for D-IN/ARC
I Open Switch for BRS1D