Advertisement
VF Snow Flurry HO
The new VF Snow Flurry HO snow machine features a snow juice
level sensor. When the snow juice level reaches a low level, a built-in
sensor inside the reservoir will automatically shut off the pump. This
will greatly expand the life of the pump.
This unit includes a switch located on the rear panel that allows
you to control the speed of the air pump located inside the unit.
This switch controls the size of the flakes that are produced by the
machine. In the max position the air flow will be low, producing larger
flakes. In the minimum position the air flow will be higher produc-
ing smaller flakes. The snow output volume is controlled using the
included remote control.
VF Snow Flurry HO
1. Open the shipping carton and carefully remove the unit from the
shipping carton.
2. Be sure to remove all the packing material especially around the
nozzle/sock.
3. Set the snow machine on a flat dry surface. Locate the included
bracket from the package and install it using the supplied hard-
ware to the side casing. Note: The bracket is an optional accesso-
ry and may not be used if desired, however if you intend to sus-
pend the unit from truss the bracket must be used.
4. Remove the fluid reservoir cap and fill it with American DJ
snow juice only and replace the reservoir cap.
5. Place the feeder tube with the filter deep inside the reservoir and
tighten the cap.
6. Using the switch on the rear of the unit, set the air volume output
to either the minimum air volume setting (large snow flakes) or the
maximum air volume setting (small snow flakes).
7. Firmly attach the remote control unit to the rear remote control
socket on the unit. Turn the rotary knob, clockwise to set
a small to large snow output.
8. Plug the unit in to a matching power supply. Switch on the main
power located on the rear of the unit.
NOTE: The liquid reservoir will glow green when power is
applied.
ADJ Products, LLC - VF Snow Flurry HO - Instruction Manual Page 6
Description
VF Snow Flurry HO
DMX Mode:
The VF Snow Flurry HO has 1 DMX channel.
1. This function will allow you to control the fixture with a standard
DMX 512 controller.
2. You can directly plug the DMX cable and controller into the snow
machine and the snow machine will automatically detect the DMX
signal. When it detects it the display will show the DMX address,
you can use the UP or DOWN buttons to change the current DMX
address if you desire, and press ENTER to set the address.
3. The other way to connect via DMX is by setting the DMX address
first using the UP or DOWN buttons then pressing ENTER. The
address you have set will be the saved address and will appear
Set-Up
everytime you connect to DMX until you change the address.
4. After you have set your DMX address plug in the fixture via the
XLR connections to any standard DMX controller. Follow the set-
up specifications that come with your DMX controller.
VF Snow Flurry HO
Channel
1
brand
®
VF Snow Flurry HO
The UC IR (not included) infrared remote gives you control of sim-
ple functions. To control the fixture you must aim the remote at the
front of the fixture and be no more then 30 feet away. Note: When
DMX mode is active, UC IR will be inactive. UC IR function auto-
matically saves the data from the last action.
1. To run your fixture using the UC IR, use the digital menu located
on the rear panel of the unit. Press the MENU button until "Ir" is
displayed and press ENTER.
STAND BY - On/Off
"DIMMER +" and "DIMMER -" - Use these buttons to adjust the out-
put intensity. "+" increases snow output, "-" decreases snow output.
Value
0 - 10
FAN OFF NO SNOW OUTPUT
11 - 255
FAN ON SNOW OUTPUT
LEAST - MORE OUTPUT
ADJ Products, LLC - VF Snow Flurry HO - Instruction Manual Page 7
DMX Operation
DMX Values & Traits
Function
SNOW OUTPUT
ADJ UC IR Control
Advertisement
