INSTRUCTION MANUAL (UH-0413L Series _Ver. 1.2) H.264 Video Compression Universal Hybrid Realtime Digital Video Recorder User Manual About this user guide Before installing and using this unit, please read this user guide carefully. Be sure to keep it handy for later reference...
Safety Precautions Explanation of Graphical Symbols This symbol indicates the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. This symbol indicates the presence of Uninsulated ”dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
Page 3
These precautions must be followed for safety reasons. Warning Do not uses if the unit emits smoke, strange sounds are heard, or odor is emitted. Make sure the power cable is not damaged. Make sure there is no dust accumulation on the power plug or the outlet. ...
Product Components The package contains the main unit and its components as specified below. When you purchase the unit, Please check to ensure the components specified below are included. DVR Set(L Front Type) Client Software CD Remote Control Battery1.5V (AAA x 2EA) Quick Guide HDD data power cable(SATA) HDD mounting bracket &...
Mounting the HARD DISK 1. Remove the screws and the top cover as specified below. 2. Mount the HDD into the mounting bracket as specified below. 3. Insert the HDD bracket and mounting screw as specified below. 4. Connect the HDD SATA and HDD power cable as specified below. NOTE) Please mount all HDDs which you want to use when installing at the first time.
Specifications Please note that specifications and unit exterior design are subject to change without notification MODEL UH-0413L Description Analog/HD Universal Hybrid DVRs (Real time) Video Input Number of Channels Camera HD-SDI (720p25/30/50/60, 1080p25/30, 1080i50/60) or NTSC/PAL Output Main Monitor HDMI and VGA (1920x1080)
Page 9
Rear User I/F Input Method IR, Mouse, Keyboard Controller Network Inteface 10/100 Base-T Dynamic DNS Yes (Free DDNS) Dual Encoding for Network Features Digital Zoom DLS (Day Light Saving) NTP (Network Time Protocol) S.M.A.R.T Internal Beep Multi-Language e-mail Notification Network 3G Mobile iPad / iPhone / Android Access...
Table of Contents Main Features ......................13 Name, Function and Connection ................14 2-1. Front Panel ........................... 14 2-2. Rear Panel ........................... 14 2-3. Remote control ..........................15 Setting up the DVR ..................... 16 3-1. Setup – Main Screen ........................16 3-1-1.
Page 11
4-4. Digital Zoom in Live and Playback Screen ..................51 5. PTZ Control ........................52 6. Back up ......................... 53 6-1. Still Image backup onto USB flash Drive..................53 6-2. Video backup onto USB flash Drive ....................53 6-3. Transferring still images or video from the ARCHIVE list .............. 54 6-4.
Page 12
9-7-8. Upgrade ............................ 91 9-7-9. Information ..........................91 9-8. Operation ............................. 92 9-8-1. Addition, Delete, and modify of DVR sites ............92 9-8-1-1. Addition of sites ..................... 92 9-8-1-2. Delete of sites ....................92 9-8-1-3. Modify of sites ....................93 9-8-2.
1. Main Features All Video input is detected automatically(Analog / 960H / HD-SDI) UH Series can Mix any input such as Analog, 960H and HD-SDI. H.264 Video compression Reliable File system HDMI & VGA Output ...
2. Name, Function and Connection 2-1. Front Panel The following information will help you to operate the front panel controls. Figure 2.1.1. Front panel ① USB PORT: To connect USB Thumb drive to backup data. ② HDD: The indicator blinks during recording and playback. ③...
2-3. Remote control Figure 2.3.1. Remote Controller Button ① ID: To set the remote control ID. ② REC: To start and stop manual recording ③ SEARCH: To go to SEARCH menu. ④ F/ADV: During playback – To move the playback position 60 seconds forward . ...
3. Setting up the DVR The following sections detail the initial setup of a DVR. 3-1. Setup – Main Screen When booting a system at first, the following messages display. After initializing, select a language and set the time. To enter the setup menu, select a right button of the mouse or press the SETUP button on the remote control.
SYSTEM INFORMATION: Display a software version, storage size, network type, IP address, MAC address, DDNS status, DVR ID and remote controller ID of the system. SYSTEM LOCK: To lock the system, user input a password. To unlock the system, please press ESC button for 5 seconds on a front panel or a remote control.
Page 18
SPOTOUT ON EVENT SPOT EVENT DWELL TIME SEQUENCE SEQUENCE DWELL TIME SPOT CHANNEL – CHANNEL MOTION ZONE MOTION SENSITIVITY – KEY TONE – REMOTE CONTROLLER ID – SENSOR TYPE STORAGE – OVERWRITE – DISK FORMAT – DISK INFO – RECORDING LIMIT RECORDING LIMIT DAYS ...
Page 19
– WEB PORT – NETWORK TYPE (DHCP, STATIC) SUBNET MASK GATEWAY DNS(PRIMARY) DNS(SECONDARY) – DDNS DDNS SERVER 1 DDNS SERVER 2 DDNS SERVER 3 – NETWORK STREAM RESOLUTION FRAME RATE QUALITY – WIRELESS LAN CONFIG – SAVE SETUP TO A USB –...
3-2. Setup – Display Mode In the SETUP menu, select the DISPLAY tab. Then, the DISPLAY menu is displayed as pictured below. Navigate through the menu items or change the settings using the mouse or the remote control. To return to the previous setup menu screen, press the ESC button.
SEQUENCE- Set the dwell time of each, single channel display in sequential display DWELL TIME mode (3~60seconds) CHANNEL Select a channel to apply the name and covert settings change using the mouse or the remote control. Select a channel to apply the following settings using the mouse NAME Set the channel name.
Page 22
the remote control. To change the values of all channels, take the following steps. Select the button to change the values of all channels. (RESOLUTION, FRAME RATE, QUALITY, RECORDING, PRE RECORD, POST EVENT RECORD and AUDIO) RESOLUTION Select 1920x1080, 1920x540, 1280x720 or 960x480, 640x360 using the mouse or the remote control.
3-3-1. Recording Schedules To setup a recording schedule, select SCHEDULE in the RECORD menu. Navigate through the menu items or change the settings using the mouse or the remote control. [Channel]: Select the specific channel. [Setup]: Set up using the left button of the mouse to section under the specific day and time. It can set the all section under the specific day or time at a time when pressing the specific day or time.
3-4. Setup – Device Mode In the SETUP menu, select the DEVICE tab. Then, the device menu is displayed as pictured below. Navigate through the menu items or change the settings using the mouse or the remote control. Figure 3.4.1. Device mode setup screen Table 3.4.1.
(9 – Highest sensitivity, 1 – Lowest sensitivity) KEY TONE Enable/disable key tone from front panel usage. REMOTE CONTROL ID Set the remote control ID. 1. Select ID. 2. Input the remote control ID number. 3. An icon will indicate on the Live Screen if the remote control ID is synchronized.
Controller (Keyboard Controller): If a PTZ controller is used, select a controller protocol from Controller menu. Set SPEED (Baud Rate) and ID number. Figure 3.4.1.2. Controller Selection Screen 3-4-2. SPOT OUT Figure 3.4.2.1. SPOT OUT setup Screen Table 3.4.2.1. Menu item in SPOT-OUT Setup screen Item Description SPOT OUT...
3-4-3. Motion Zone Setup Select MOTION ZONE using the mouse or the remote control and select either PARTIAL ZONE or FULL ZONE using the mouse control. The default value is FULL ZONE. If FULL ZONE is selected, the motion setting screen is not displayed. Only set the level of sensitivity for MOTION SENSITIVITY.
3-5. Setup – Storage Mode In the SETUP menu, select the STORAGE tab. Then, the STORAGE menu is displayed as pictured below. Navigate through the menu items or change the settings using the mouse or the remote control. Figure 3.5.1. STORAGE setup screen Table 3.5.1.
RECORDING LIMIT Overwrite(off) and Recording Limit(off): When disk is full, the DVR stop recording. Overwrite(Don’t care) and Recording Limit(on): The DVR doesn’t stop recording. The amount of data in HDD is always that of “Recording Limit Days”. RECORDING Set the recording limit days. (1- 90 days) LIMIT DAYS If the RECORDING LIMIT DAYS are set to 1, the data will be overwritten after 24 hours.
Page 30
DVR ID Name the DVR (e.g. Factory, Library, Store, Location etc) This is to used to identify the name of each DVR under the same network. DESCRIPTION Press the button to view the system information. (Software Version, Storage Size, IP Address, MAC Address and DDNS Status) LANGUAGE Select the display language using the mouse or the remote control.
Page 31
button. Caution - Do not set the start time to 23:00 for DLS. - DLS cannot be applied if the date of BEGIN and END is the same. CLIENT ACCESS Enable/Disable remote access through the network. NTP (Network Time Protocol) which synchronizes the time of the computer systems over variable-latency data networks.
Page 32
SERVER TYPE: Select GMAIL, HOTMAIL, AOL, YAHOO or MANUAL) MAIL SERVER: Enter the appropriate mail server information. MAIL PORT: Assign Mail Port number. SECURE OPTION: Select the secure mail server connection method. (SSL or TLS) ID: Enter the appropriate mail server ID. PASSWORD: Enter the appropriate mail server PASSWORD MAIL TO: Enter the appropriate email address to enable sending e-mail reports using a virtual keyboard.
Page 33
VIDEO CLIP SETUP – Set video recording time for the e-mail appending Features motion detection or alarm input events only EVENT AND NOTIFICATION – OFF, ON (Allows the user to set EVENT NOFICIATION ON or OFF) HEALTH CHECK / RESTART / SHUTDOWN / PANIC RECORD Enable Email Notification in the event a problem occurs with the DVR.
3-7. Setup – SECURITY Mode In the SETUP menu, select the SECURITY tab. Then, the SECURITY menu is displayed as pictured below. Navigate through the menu items or change the settings using the mouse or the remote control. Figure 3.7.1. SICURITY setup screen Table 3.7.1.
Page 35
ADMIN, NETOWRK, USER1, USER2, USER3: V check: It means the user can access to the function. Blank: It means the user cannot access to the function. USER NAME Change the name of USER1, USER2 and USER3. Click “ENTER” after naming. USER PASSWORD Options are ADMIN, USER1, USER2 and USER3.
When user set this function, they can see a user login window. Then, user can select one of user types ◀ ▲ ▶ ▼ (ADMIN, USER1, USER2, USER3) using the mouse or the control button ( ) on the remote control.
DHCP DVR will automatically retrieve an IP address. STATIC Network information must be manually configured IP Enter IP address that is assigned for the DVR SUBNET MASK Enter Subnet Mask that is assigned for the DVR GATEWAY Enter Gateway that is assigned for the DVR. DNS (PRIMARY) The address for the primary DNS server DNS (SECONDARY) The address for the secondary DNS server DDNS...
Network access beyond a router In order to access the DVR remotely beyond a router (firewall), the user must open TCP port for command level, live/storage channels. User need to open port number 5445 and 5445. If the DVR supports remote setup and upgrade function over the network, user need to open additional port number 80.
The maximum value for the network stream is VGA 15fps per channel but the recording resolution and frame rate are sending when only one user connects to the one channel mode via network. UH-0413L: Up to 120 fps @VGA Figure 3.8.4. Network setup screen – Network Stream...
3-9. Setup - CONFIG Mode In the SETUP menu, select the CONFIG tab. Then, the configuration menu is displayed as pictured below. Navigate through the menu items or change the settings using the mouse or the remote control. Figure 3.9.1. Config setup screen Table 3.9.1.
Page 41
LOAD DEFAULT Press the button to reset the system to the default settings. The following settings such as Language, DVR ID, Security User Authentication, Security User P/W, Date format, DLS settings, Network settings, HDD overwrite, Limit recording, HDD serial number, and HDD ERROR time will not be included. LOAD FACTORY Press the button to reset the system to the factory default settings.
4. Live, Search and Playback 4-1. Live Viewing Screen In the Live screen, video inputs from the cameras are displayed as they are configured in the Display Setup screen. Various on-screen display (OSD) symbols, which indicate the status of the DVR, are described in Table 4.1.1.
Page 43
Sequence button. Click this button to use a sequence function. Manual Record button. Click this button to record at once. Alarm-out function On/Off button. An alarm is stopped and an alarm setup lamp is right out when it clicks this button during the alarm is in progress. Click the split screen icon to change the current split screen mode using the mouse or SEL button.
Page 44
Right click the mouse, and the quick operation window will be displayed as below. Figure 4.1.2. Quick Operation Window Table 4.1.2. Menu Items in Quick Operation Window Icon Description SETUP Select this option to enter the Setup menu. AUDIO Select this option to mute audio on all channels. SEARCH Search button.
CHANNEL Press the button to view the record setting of a selected channel. INFORMATION SYSTEM Press the button to view the system information. INFORMATION SYSTEM LOCK Locks the DVR from unauthorized user access. SYSTEM Select this option to shutdown system. SHUTDOWN 4-2.
4-2-1. QUICK Search The Quick Search window is used to find stored video with ease using the thumb nail playback screen. Figure 4.2.1.1. Quick Search screen 1. When the Quick Search menu is selected, the user can see a calendar, which displays recorded dates with highlights.
4-2-2. TIME-LINE Search The TIME-LINE search window is used to find the stored video by using the time line bar. Figure 4.2.2. Time Line Search screen When it clicks a Timeline menu, user can see a calendar which has recording data. Select a specific date and time.
Figure 4.2.3.1. Event Search screen When the Event menu is selected, the user can see a calendar, which has recorded data. Select a specific date and the event log will be displayed. Press the PLAY button to playback the data or the SAVE button to save the data after selecting the specific data.
4-2-7. Archive Search The ARCHIVE Search window is used to find previously stored video or images. Figure 4.2.7. Archive Search Screen When it clicks an Archive menu, user can see a calendar which has recording data. Select a specific date and then user can see all data.
4-3. Play mode During playback of a recorded event, the mode changes from SEARCH to PLAY. While in PLAY mode, you may return to the SEARCH screen by pressing the X button on the status bar or the ESC button of a remote control.
4-4. Digital Zoom in Live and Playback Screen DVR series supports Digital Zoom feature during live and playback mode. 1. Double click the target channel. 2. Click the left button of the mouse and drag to make rectangular shape.
5. PTZ Control To control the PTZ functions of the camera, select PTZ menu on the screen using the mouse. Please refer to the table 5.1. for the control. Table 5.1. Button Functions in PTZ Control Item Description INITIALIZE Initialize the PTZ settings of the selected camera. ◀...
6. Back up 6-1. Still Image backup onto USB flash Drive Still images can be captured and archived onto the USB flash drive or an USB external hard drive in live mode or while playing back recorded video. In live mode, press the BACKUP button to launch the archive function or select BACK UP menu on the screen using the mouse.
6-3. Transferring still images or video from the ARCHIVE list The stored data onto hard drive will be found in the ARCHIVE list in SEARCH window. User can back up still images or video into the storage device from the ARCHIVE list. 1.
6-4. Playback of Backup Video NSF format: NSF format video can be played back by the player (the HD player) that the DVR copies on USB flash drive with video. Two folders are copied on USB flash drive - BACKUP DATA: NSF format video file and INDEX file for a title file of date and time - HD PLAYER: Exclusive video viewer.
7. Upgrading Firmware In order to upgrade, the firmware upgrade file must first be downloaded and copied into the USB memory drive. Create a new folder in the USB memory drive and name it “upgrade”. Copy the firmware upgrade file “xxxxxx.bin”...
Page 57
3. You can see the following message when pressing the scan button. Please check the current firmware version and the firmware version which you want to upgrade. The system will upgrade automatically when pressing the upgrade button. After upgrading, the system should be restarted. At that time, the USB memory drive has to be pulled out on the system.
Page 58
Remote Firmware Upgrade User can upgrade the firmware via Network as follows. 1. Go to the Remote Setup menu on the UMS Single, UMS Multi or Web Viewer. 2. Press the password for admin. Just admin is possible to connect to the remote setup menu.
Page 59
3. Go to the Remote Upgrade menu. Then, you can see the current F/W version as follows. To upgrade a new F/W, insert the F/W in your PC and press the UPGRADE button. 4. Then, you can see the following progress bar and it would be taken around 150 seconds to upgrade. 5.
8. Network access using the Exclusive network viewer, UMS single The DVR provides a live remote monitoring feature. Remote monitoring requires installation of the network viewer on your PC. NOTICE In a high bandwidth network, a maximum of four users can access one DVR simultaneously. In a low bandwidth network it is recommended that only one user access the DVR at a time.
8-3. Live monitoring mode and functions. Button Function Description DATE & TIME Displays the current date and time. CONNECT/DISCONNECT Connect/disconnect network connection. SEARCH Switches the live mode to search mode. DISPLAY MODE Select a channel and screen display mode. PAN/TILT/ZOOM/ FOCUS Control the PAN / TILT / ZOOM / FOCUS features on the remote camera.
Page 62
HDD USAGE DVR HDD storage Indicator. NETWORK BANDWIDTH Shows the transferred frames and network bandwidth. AUDIO Adjust the volume. The audio can be turned on or off by clicking the audio icon. LOG WINDOW Display the connection status of DVR Operations of the display mode of the main screen ...
Image capture of live screen Still-image of live screen can be captured and saved as BMP or JPEG file. 1. Click the channel to be captured. Then the channel screen is surrounded with a red line. 2. Click the CAPTURE button. Then the IMAGE CAPTURE dialog is displayed. 3.
Page 64
DISCONNECT Disconnect network connection.. LIVE Switches the search mode to live mode. DISPLAY MODE Select a channel and screen display mode. SEARCH The calendar shows dates with recorded video CALENDAR in a light blue and the selected date in dark blue.
Page 65
click the play icon to display the recorded video. CHANNEL To display the recorded data of selected channel or all channels on a time line scale. Searching and playing video in the remote DVR Video recorded in the remote DVR or Video recorded on the PC can be searched and played back. 1.
Backup of video in the remote DVR Video recorded in the remote DVR cab be backed up on the PC HDD as AVI format. 1. Connect the network to the remote DVR and play the video recorded in the remote DVR. 2.
Page 67
Setting General Set the Security Option, Save Path, and Miscellaneous. Security Option: Set a password for security options. When you access any of the selected functions, you will need to enter the password. Save Path: Specify the location to record for backup and still image capture. ...
Page 68
ID: Input ID of DVR. Default ID is “admin”. Password: Input network password of DVR. Default Password is “1111”. Click OK button. And then the registered site is added on the directory window. Setting Event Set the record path and the size of local disk space for the log files. ...
Page 69
Setting Record Record Setup: You can set the recording conditions as the following; Always, Event, or Auto record. And you can also select target DVR/DVRs and channel/channels When you set the recording condition to event, you can set event for motion or alarm with duration. Record Local Storage Setup: You can select the local disk to record and the amount of disk space you want to allow the program to use for recording.
Page 70
Setting Secondary Monitor Used to calibrate the second monitor image. Setting Language English, French and Spanish is selectable. About “About” provides network client version information.
8-7. UMS Client Connection Click CONNECT button to appear on the site registered under the ”OK” button is pressed, the connection to the site. If you want to connect directly to an IP address or Domain address to “OK” button...
9. Network access using the Exclusive network viewer, UMS Multi 9-1. Overview The UMS Multi-Client is a multiple site monitoring client software with; video, audio, and alarm signals from the DVRs over networks. The UMS Multi-Client does not limit the number of DVR units to register. The program displays to up 256 live videos on one display and even playback videos window on the same or another display monitor.
9-3. Installing the program 1. Insert the provided CD in the CD drive and double-click “UMSMultiClient (XXXX).exe” 2. Select a destination folder and click “Next”. 3. Select the program folder and click “Next”. 4. The setup status screen is displayed. 5.
9-4. Live Window When installation is completed, double click the “UMS Multi Client” icon on your desktop to start the program. 9-4-1. Main user interface 9-4-2. Control buttons Button Description Click this icon to run a playback window to search and play videos that are recorded in local PC.
Page 75
Click this icon to setup configuration of UMS MULTI CLIENT. SETUP Click this icon to capture a still image CAPTURE Opens list of events logged by the UMS Multi Client. EVENT LIST Click this icon to play/pause live video. PAUSE Click this icon to turn on/off alarm outputs.
9-5. Search and Playback Window 9-5-1. Main user interface You can access to search window by clicking the search icon (Local Playback / Remote Playback) on the upper left of Live Window. 9-5-2. Main control panel Button Description Click this icon to run a playback window to search and play videos that are recorded in local PC.
Page 77
Click this icon to set the beginning time for backup of the recorded MARK IN video in AVI format. Click this icon to set the ending time for backup of the recorded video MARK OUT in AVI format. Click this icon to backup the recorded video in AVI format. BACKUP Use the volume control bar to set the audio level.
9-6. Setup of UMS Multi Client Click the setup icon to setup the configuration of UMS Multi Client software. The Setup window displayed as below. 9-6-1. General Security Option: Set a password for security options. Select security options and set a password. Then when you access any of selected functions, you need to enter the password.
9-6-2. Event Event log can be archived and searched. Event Log: Specify the location to save event logs and select event to archive. Event Search: Event log can be searched from the selected time.
9-6-3. Record Record Setup: You can set the recording conditions as the following; Always, Event, or Auto record. And you can also select target DVR/DVRs and channel/channels. When you set the recording condition to event, you can set event for motion or alarm with duration. Record Local Storage Setup: You can select the local disk to record and the amount of disk space you want to allow the program to use for recording.
9-6-6. About “About” provides network client version information. 9-7. Remote Setup The menu settings for the DVR unit can be set over network. Put the cursor of the mouse on the channel, which is connected to the site and right click on the mouse to open the submenu.
NOTICE Web Setup is prohibited when DVR is in local Setup Menu. 9-7-1. Display Select the DISPLAY tab to set the DISPLAY conditions. These settings apply to all channels. OSD: Sets whether to display or not date and time as well as channel number on the screen. OSD CONTRAST: Adjust the character contrast on the screen.
9-7-2. Record Select RECORD tab to set the recording conditions. These settings apply to the specified channel only. Recording Setup o RESOLUTION: Sets the resolution for the recordings. The set value applies to an individual channel. o FRAME RATE: Sets the recording rate. o QUALITY: Sets the image quality in 5 levels.
9-7-3. Device Select Device to set Alarm Out, Controller and PTZ, SPOT Out, Motion zone ALARM OUT: Set the Alarm Output Connector. o ALARM DURATION: Set alarm dwell time from 5 to 60 seconds or infinite. CONTROLLER: Set the controller baud rate and ID. ...
9-7-4. Storage Select Storage to configure continued recording settings by overwriting the hard disk and the storage period for the recording data. OVERWRITE: Select on to continue recording by overwriting when the hard disk becomes full. DISK INFO: Hard drive information. ...
9-7-5. System Select System to set system and time settings. DATE FORMAT: Select the date display format. CLIENT ACCCESS: Enable/Disable remote access through network client software. NTP SETUP: Sets whether to synchronize the time using NTP server or not. ...
Page 88
o Connection Mode: Select the connection mode to NTP time server. SEND E-Mail SETUP: Sets whether to enable/disable e-mail sending function. o SEVER TYPE: Select GMAIL, HOTMAIL, AOL, YAHOO or MANUAL) o MAIL SERVER: Input the SMTP server name as well as the user ID and password. o MAIL PORT: Mail port setting.
9-7-6. Security Select the Security tab to set the DISPLAY conditions. USER AUTHORITY: Select which users have access to each function, password check can be implemented for each function accessed. USER PASSWORD: Select Username to change Password CHANGE: Select whether to KEEP or CHANGE the current password. NEW PASSWORD: Input NEW Password if CHANGE was selected.
9-7-7. Network PORT: When connecting multiple DVRs to the network, set a unique port number. NETWORK AUDIO PORT: Display the network audio port (NETWORK PORT + 1). WEB PORT: Set a web server port number. NETWORK TYPE ( Cannot be altered remotely ) ...
9-7-8. Upgrade Shows the current Firmware version installed on DVR. Browse: Select BROWSE to locate the firmware file. Upgrade: Select UPGRADE to upgrade the firmware of the DVR. Please refer to page 59 for the Remote Upgrade. 9-7-9. Information Display general information about the DVR.
9-8. Operation 9-8-1. Addition, Delete, and modify of DVR sites 9-8-1-1. Addition of sites 1. Click SITE ADDITION button. And then the following window will be displayed as below. o Model: User has to select surely a suitable type. SDVR series, H series DVR N series DVR, HD DVR IP Camera o Site Name: Input a name that properly describes a site.
2. Click SITE DELETE button. And then the selected site/sites is/are deleted. 9-8-1-3. Modify of sites 1. Select the site/sites to modify from the directory window. 2. Click NET FINDER button. And then the following window displays. 3. Click MODIFY button. And then the modified information is applied. 9-8-2.
2. Click CONNECT button, and then site/sites displays/display as connected. 9-8-2-2. Disconnect 1. Select site/sites to disconnect from the directory window. 2. Click DISCONNECT button, and then selected site/sites disconnected.
9-8-3. Still-image capture during Live 1. Double-click a channel to capture from the display screen. (Otherwise all channels will be captured.). 2. Click CAPTURE button. And then a Capture window displays. 3. Set Save path, File Name, and File Format. And then click OK button. 4.
9-8-4. Recording Video on local PC during Live 1. Click SETUP button. And then a setup window display. 2. Select Record and set the values. 3. Select Disk and set the values. 4. Click RECORD ON button. And the color of button is changed. 5.
9-8-5. Local Playback and Remote Playback 9-8-5-1. Playback of recorded video on local PC 1. Click LOCAL PLAYBACK button. And then Playback Window display over Live Window. 2. Select site/sites to connect from the directory window. 3. Click CONNECT button. And then Green bar displays on Search calendar and slide window. 4.
9-8-5-2. Playback of recorded video on remote DVR 1. Click REMOTE PLAYBACK button. And then Playback Window display over Live Window. 2. Select site to connect from the directory window. 3. Click CONNECT button. And then Green bar displays on Search calendar and slide window. 4.
9-8-6. AVI Backup during playback You can back up the recorded videos in AVI format during playback. 1. Double-click the target channel to backup. 2. Select the beginning time by using the search calendar and slide bar. 3. Click MARK IN button, when the scale of the timeline is located on the target time as the beginning time of backup.
Notice When it does a backup with NSF format, user can do a playback using the DVR player. The DVR player is installed with the S/W in user’s PC. 10. Network – By an web-browser viewer The DVR provides a live remote monitoring feature by web-browser viewer. (NOTE: Web-Brower is only available for Internet Explorer) 1.
Page 101
4. Click “Install” to download ActiveX control. 5. Web Browser Viewer is displayed as bellow. 6. Click CONNECT button on the Left upper corner of web-viewer. Then “Connect” dialog is displayed. Enter IP address (or Domain name address that you pre-registered on www.bestddns.com, www.okddns.com or www.ddnscenter.com, Port number and Password and click “Connect”...
APPENDIX: How to connect network A. How to set IP address of the DVR and open TCP port of the router? The port forwarding is dependent on the brand and model of the router. The port forwarding is required to allow access to the DVR beyond a router.
Page 103
3. But if IP is something else like 192.168.XXX.XXX., you should change IP address, Subnet, Gateway on the DVR. Go to SETUP>NETWORK>LAN of the DVR and change the IP settings to be like IP: 192.168.XXX.XXX and Gateway: 192.168.XXX.XXX. (Refer to the user’s manual of Router.) Open your web browser.
7. Select the Save settings button located on the bottom of the window. Then Port forwarding is finished. Network access beyond a router In order to access the DVR remotely beyond a router (firewall), the user must open TCP port for command level, live channels and storage channels.
Page 105
Internet (ADSL) Connection using DDNS Dynamic Domain Name System (DDNS) allows a domain name to be constantly synchronized with a dynamic IP address. A current dynamic IP address is being associated with a static domain name. 1. Go to SETUP>NETWORK. Set NETWORK TYPE as DHCP and DDNS SERVER as ON. And select one type among bestddns.com, okddns.com and ddnscenter.com after setting to DDNS1.
Page 106
7. If you see the screen “You can use the Domain name you entered” then click RETURN and click REGISTER button to complete the registration. 8. Run the pre-install the network client software on the supplied CD. 9. Click button and add the DVR as necessary. ...
C. How to access DVR with iPhone? Notice Data Usage applied without Wi-Fi connection. Please check with your Phone Carrier. App Viewer for iPhone 1. Enter the Apple App Store. 2. Search “iUMS” in the App Store. LIVE 1. Open the installed “iUMS” App and click button to add a remote device.
Page 108
5. To select the display mode(1, 4, 9, 10 or 16 split display), tap the arrow menus button 6. Drag and drop channels Touch and drag one channel to the other channel to swap the channel location. To swap the channel, drag a channel to another channel.
Page 109
Playback 1. Select Mode as ‘Playback’ and click ‘CONNECT’ button. Then select Date & Time and click PLAY button. 2. The app will display the selected channel(s). Double tap the channel screen to switch 1 channel display to 4, 8, 10, 16 channels split display depending on the DVR. 3.
D. How to access DVR with Android? App Viewer for Android Phone 1. Enter Google Play Store. 2. Search “iUMS” in the Android Market and install the “iUMS” app. Live 1. Open the installed “iUMS” App and select the Live Preview. Then click the menu button of the phone to add a remote device.
Page 111
Playback 1. Select the registered device and select PLAYBACK and select up to 4 channels to search. Then click START button. 2. The app will display the selected channel(s). Double tap the channel screen to switch 1 channel display to 4 channels split display.
Page 112
PTZ Control To control the PTZ function of the camera, tap the channel screen, then the channel name will be highlighted in Yellow. Using the PTZ menu icons on the screen, control PTZF.
Need help?
Do you have a question about the UH-0413L and is the answer not in the manual?
Questions and answers