Casio 5470 Operation Manual page 25

Digital Compass
Q1
The entire display is flashing.
Abnormal magnetism has been detected.
Move away from any potential source of
strong magnetism and try taking a reading
again.
If the display flashes again, it could mean
●
that the watch itself has become
magnetized. Move away from any potential
source of strong magnetism, perform
bidirectional calibration, and then try taking
a reading again.
Calibrating Compass Readings
l
(Bidirectional Calibration)
Digital Compass Reading Precautions
l
Q2
[ERR] appears during measurement.
There is a problem with the sensor or there
may be a source strong magnetic force
nearby. Move away from any potential source
of strong magnetism and try taking a reading
again. If [ERR] keeps appearing after multiple
measurement attempts, contact a CASIO
service center.
Digital Compass Reading Precautions
l
Q3
[ERR] appears following
bidirectional calibration.
If [- - -] is followed by [ERR] on the display, it
could mean there is something wrong with the
sensor.
If [ERR] disappears after about one second,
●
try performing bidirectional calibration
again.
If [ERR] continues to appear even after
●
multiple attempts, contact your original
retailer or CASIO service center.
Q4
Direction information indicated by the
watch is different from that indicated
by a backup compass.
Move away from any potential source of
strong magnetism, perform bidirectional
calibration, and then try taking a reading
again.
Calibrating Compass Readings
l
(Bidirectional Calibration)
Digital Compass Reading Precautions
l
Q5
Readings at the same location
produce different results.
Cannot take readings indoors.
Move away from any potential source of
strong magnetism and try taking a reading
again.
Digital Compass Reading Precautions
l
Operation Guide 5470
Barometric Pressure
Measurement
Q1
Following a relative barometric
pressure reading, the watch's
second hand points to 9 o'clock.
The second hand will move to 9 o'clock if a
reading is outside the allowable barometric
pressure measurement range (260 hPa to
1,100 hPa (7.65 inHg to 32.45 inHg)). If [ERR]
appears on the display, there may be a
problem with the sensor.
Checking the Change in Barometric
l
Pressure between Two Readings
Q2
[ERR] appears during measurement.
There may be a problem with the sensor. Try
taking another measurement. If [ERR] keeps
appearing after multiple measurement
attempts, contact a CASIO service center.
Temperature Measurement
Q1
[ERR] appears during measurement.
There may be a problem with the sensor. Try
taking another measurement. If [ERR] keeps
appearing after multiple measurement
attempts, contact a CASIO service center.
World Time
Q1
The time for a World Time City is not
correct.
The summer time setting (standard time/
summer time) is wrong.
Configuring the Summer Time Setting
l
Hand Movement and
Indications
Q1
I don't know what mode the watch is
in.
You tell which mode the watch is currently in
by checking the position of the mode hand.
Navigating Between Modes
l
Hold down the (B) button for about two
●
seconds to enter the Timekeeping Mode.
Timekeeping Mode
Q2
The second hand is jumping at two-
second intervals.
Battery power is low. Keep the watch exposed
to light until it recharges sufficiently.
Checking the Charge Level
l
Q3
All hands are stopped and buttons do
not work.
The battery is dead. Keep the watch exposed
to light until the battery recharges sufficiently.
Checking the Charge Level
l
Q4
The hands suddenly start moving at
high speed.
This is due to one of the reasons below, and
does not indicate malfunction. Simply wait
until normal hand movement resumes.
The watch is recovering from a power
●
saving state.
Power Saving Function
l
A time signal is being received and the time
●
setting is being adjusted.
Auto Time Adjustment
l
Q5
Hands are stopped and buttons do
not work.
The watch is in the charge recovery mode.
Wait until the recovery process is complete
(for about 15 minutes). The watch will recover
more quickly if you place it in a brightly lit
location.
Q6
The time indicated by the hands is
different from the digital time.
Strong magnetism or impact may cause the
hands of the watch to go out of alignment.
Correct hand position alignment.
Adjusting Hand Alignment
l
25