Table of Contents
Advertisement
APPLICATIONS
WARNING
tric shock, check work area for hidden pipes
and wires before drilling or driving screws.
Drilling in Wood, Composition Materials and
Plastic
When drilling in wood, composition materials and
plastic, select the
Start the drill slowly, gradually increasing speed
as you drill. When drilling into wood, use wood
augers or twist drill bits. Always use sharp bits.
When using twist drill bits, pull the bit out of the
reduce the chance of splintering, back work with a
piece of scrap wood. Select low speeds for plastics
with a low melting point.
Drilling in Metal
When drilling in metal, select the
operating mode. Use high speed steel twist drills
or hole saws. Use a center punch to start the hole.
Lubricate drill bits with cutting oil when drilling in
iron or steel. Use a coolant when drilling in nonfer-
rous metals such as copper, brass or aluminum.
Back the material to prevent binding and distortion
on breakthrough.
Drilling in Masonry
When drilling in masonry, select the
drill operating mode. Use high speed carbide-tipped
bits. Drilling soft masonry materials such as cinder
block requires little pressure. Hard materials like
concrete require more pressure. A smooth, even
let the bit spin in the hole without cutting. Do not
use water to settle dust or to cool bit. Both actions
will damage the carbide.
Driving Screws and Nut Running
Drill a pilot hole when driving screws into thick or
hard materials. Select the
Set the torque selector collar to the proper position
and set the speed to low. Use the proper style and
size screwdriver bit for the type of screw you are
using. With the screwdriver bit in the screw, place
pressure before pulling the trigger. Screws can be
removed by reversing the motor.
Overloading
Continuous overloading may cause permanent
damage to tool or battery pack.
WARNING
Only use accessories specifically recommended for this tool. Others may be hazardous.
For a complete listing of accessories refer to your MILWAUKEE
online to www.milwa ukeetools.com.au or www.milwaukeetools.co.nz. To obtain a product
catalogue, please contact your local authorized MILWAUKEE
To reduce the risk of elec-
drill-only operating mode.
driving screws mode.
ACCESSORIES
Always remove battery pack before changing or removing accessories.
WARNING
always unplug the charger and remove the
battery pack from the charger or tool before
performing any maintenance. Never disas-
semble the tool, battery pack or charger.
Contact a
ALL repairs.
Maintaining Tool
Keep your tool, battery pack and charger in good
repair by adopting a regular maintenance program.
After six months to one year, depending on use,
return the tool, battery pack and charger to
your local authorized
service centre for:
• Lubrication
• Mechanical inspection and cleaning (gears, spin-
drill-only
dles, bearings, housing, etc.)
• Electrical inspection (battery pack, charger,
motor)
• Testing to assure proper mechanical and electrical
operation
If the tool does not start or operate at full power
with a fully charged battery pack, clean the contacts
on the battery pack. If the tool still does not work
properly, return the tool, charger and battery pack,
to your local authorized
hammer
service centre for repairs.
WARNING
sonal injury and damage, never immerse your
tool, battery pack or charger in liquid or allow
a liquid to
Cleaning
Clean dust and debris from charger and tool vents.
Keep tool handles clean, dry and free of oil or
grease. Use only mild soap and a damp cloth to
clean the tool, battery pack and charger since certain
cleaning agents and solvents are harmful to plastics
and other insulated parts. Some of these include
gasoline, turpentine, lacquer thinner, paint thinner,
chlorinated cleaning solvents, ammonia and house-
hold detergents containing ammonia. Never use
Repairs
For repairs, return the tool, battery pack and
charger to the nearest service center.
6
MAINTENANCE
To reduce the risk of injury,
MILWAUKEE
®
service facility for
MILWAUKEE
MILWAUKEE
To reduce the risk of per-
inside them.
®
accessories catalogue or go
®
dealer or service centre.
®
dealer or
dealer or
®
Advertisement
Table of Contents
