Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for FireAngel Thermoptek ST-625
Summary of Contents for FireAngel Thermoptek ST-625
- Page 1 User Manual Smoke Alarm Model ST-625...
- Page 2 A Sprue Safety Products Brand Sprue Safety Products Ltd. Vanguard Centre, Sir William Lyons Road, Coventry CV4 7EZ UK Technical Support: 0800 141 2561 / UK Textphone users dial: 18001 0800 141 2561 EIRE dial: 1-800 523171 / Email: technicalsupport@sprue.com / Web: www.fireangel.co.uk...
-
Page 3: Table Of Contents
CONTENTS Introduction Alarm Smart Silence™ Sensor technology Sleep Easy™ Application Maintenance How to install your smoke alarm 6 Troubleshooting Operation Disposal Battery replacement Warranty Alarm test Note: This user manual is also available in large text and other formats Please email: technicalsupport@sprue.com call 0800 141 2561 for further information... -
Page 4: Introduction
Please visit optical sensing chamber provides a fast www fireangel co uk to find out about the reaction to both slow smouldering and latest additions to our range of innovative fast flaming fires in a single alarm The... -
Page 5: Application
APPLICATION WARNING: Your FireAngel smoke alarm ® can be installed into a new build property as additional protection to an existing smoke detection system only It cannot be BEDROOM HALL BEDROOM used as a substitute for a hard wired system... -
Page 6: How To Install Your Smoke Alarm
boarding houses and dormitories Your alarm as shown, making sure that the ST-625 smoke alarm can be used in positive and negative connections are in individual sleeping / resident rooms, the correct position providing the same conditions are met as for a single-family residence However, there must already be a primary fire detection system that meets regulatory... - Page 7 Base Plate Holes Fit Your FireAngel Smoke Alarm Ⓡ Hold the alarm up to the base plate and The base plate should be attached to the push and rotate the alarm clockwise into ceiling or wall using the screws and fixings...
-
Page 8: Operation
40 seconds to show that the alarm Duracell MN1500bB is active Panasonic ProPower LR6 Low Battery Condition Should your FireAngel smoke alarm enter Ⓡ Remove the alarm from its base plate by a low battery condition, the unit will emit turning anti-clockwise and pulling gently an audible ‘chirp’... -
Page 9: Alarm Test
Remove existing batteries After fitting your alarm to the base plate, replace with new batteries from the list of wait for 5 seconds for the alarm to settle recommended batteries making sure that then test the alarm the positive and negative connections are in the correct position ALARM TEST The alarm should be attached to the base... -
Page 10: Alarm Smart Silence
‘Troubleshooting’ section (see page 13) WARNING: You should test your smoke alarm every week ALARM SMART SILENCE™ DANGER: If your FireAngel smoke alarm ® emits the full alarm signal and you are not testing the unit, the smoke alarm is... -
Page 11: Sleep Easy
Your alarm will automatically return to full batteries immediately, and certainly within sensitivity on completion of the reset cycle 7 days, as your FireAngel alarm may then ® and the red LED will revert to flashing once... -
Page 12: Maintenance
® designed to be as maintenance-free as IMPORTANT: Do not use solvents or possible, however there are several things cleaners on your FireAngel smoke alarm, ® you must do to keep it working properly as they may cause damage to the sensor... -
Page 13: Troubleshooting
TROUBLESHOOTING Problem Solution • If testing immediately after first activating the alarm or replacing the batteries, you should allow a few seconds for the alarm to settle before testing • Make sure you push the centre of the test button Your FireAngel smoke ® firmly alarm does not sound • If the unit has been silenced and is in low sensitivity during testing mode it may not test Wait 15 minutes then try again • If the alarm has been recently fitted and it still fails to... - Page 14 • If the red LED flashes at a separate time from the is pressed chirp, a fault is indicated • If within warranty contact T echnical Support (see below) Otherwise replace immediately • Check the location of your FireAngel smoke alarm ® (see ‘Application’) You experience frequent • Clean the smoke alarm (see ‘Maintenance’). unwanted alarms • If the frequent unwanted alarms continue contact...
-
Page 15: Disposal
Except for death or personal injury, Sprue Safety FireAngel® Technical Support on 0800 141 2561 or Products Ltd shall not be liable for any loss of use, technicalsupport@sprue com damage, cost or expense relating to this product...
Need help?
Do you have a question about the Thermoptek ST-625 and is the answer not in the manual?
Questions and answers