Appendix; Selecting The Correct Eac Address (Ah15/Ah30) - Assa Abloy Aperio AH15 Mechanical Installation Instructions

Aperio Online
®
42

6 Appendix

Selecting the correct EAC address (AH15/AH30)

Selecting EAC addresses for communication hubs
and locks correctly during installation is important
in order not to cause address conflicts in your
installation.
The communication hubs can use different
address ranges depending on the installation:
Address 1-15: For AH30 communication hubs
∙
with one or several locks paired and AH15
communication hubs. Address is selected by DIP
Switch or the Programming Application.
Addressing table – normal address offset
An AH30 communication hub can pair with
up to 8 locks. When pairing several locks to a
communication hub, the following addresses are
used for the address range 1-15. Above this range
only one lock can be paired.
DIP 4 – DIP 1 AH30 Hub address Lock addresses
0000
0001 0x01
0010 0x02
0011 0x03
0100 0x04
0101 0x05
0110 0x06
0111 0x07
1000 0x08
1001 0x09
1010 0x0A
1011 0x0B
1100 0x0C
1101 0x0D
1110 0x0E
1111 0x0F
When configuring installations that differ from
the default configuration described in section DIP
1-5 – Selecting the EAC address/Automatic paring
on page 38, use this table to keep track of what
®
Aperio Online Mechanical Installation Guide, Document No: ST-001323-B Date: 21 februari 2014
Address 16-31: For AH30/AH15 communication
∙
hubs in single device mode (only one lock
paired). Address is selected by DIP Switch or the
Programming Application.
Address 32-63: For AH30/AH15 communication
∙
hubs in single device mode (only one lock
paired). Address is selected only by the
Programming Application.
The final lock EAC address depends on the
communication hub address. For AH15
communication hubs the lock address is equal to
the hub address. For AH30 communication hubs
the lock address is decided by the addressing
table.
Reserved
0x01, 0x11, 0x21, 0x31, 0x41, 0x51, 0x61, 0x71
0x02, 0x12, 0x22, 0x32, 0x42, 0x52, 0x62, 0x72
0x03, 0x13, 0x23, 0x33, 0x43, 0x53, 0x63, 0x73
0x04, 0x14, 0x24, 0x34, 0x44, 0x54, 0x64, 0x74
0x05, 0x15, 0x25, 0x35, 0x45, 0x55, 0x65, 0x75
0x06, 0x16, 0x26, 0x36, 0x46, 0x56, 0x66, 0x76
0x07, 0x17, 0x27, 0x37, 0x47, 0x57, 0x67, 0x77
0x08, 0x18, 0x28, 0x38, 0x48, 0x58, 0x68, 0x78
0x09, 0x19, 0x29, 0x39, 0x49, 0x59, 0x69, 0x79
0x0A, 0x1A, 0x2A, 0x3A, 0x4A, 0x5A, 0x6A, 0x7A
0x0B, 0x1B, 0x2B, 0x3B, 0x4B, 0x5B, 0x6B, 0x7B
0x0C, 0x1C, 0x2C, 0x3C, 0x4C, 0x5C, 0x6C, 0x7C
0x0D, 0x1D, 0x2D, 0x3D, 0x4D, 0x5D, 0x6D, 0x7D
0x0E, 0x1E, 0x2E, 0x3E, 0x4E, 0x5E, 0x6E, 0x7E
0x0F, 0x1F, 0x2F, 0x3F, 0x4F, 0x5F, 0x6F, 0x7F
addresses are used by the locks/sensors in your
installation in order to avoid addressing conflicts
according to section "Installation examples" on page
44 for mixed installations.