Related Manuals for Leica DISTO D410
Summary of Contents for Leica DISTO D410
- Page 1 Leica DISTO D410 Leica DISTO D410 The original laser distance meter The original laser distance meter...
-
Page 2: Table Of Contents
Area - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 15 Leica DISTO... -
Page 3: Instrument Set-Up
Important paragraphs which must be adhered to in practice as they enable the product to be used in a technically correct and Navigation Function efficient manner. screen Return / Equal Add / Clear / Off Subtract Leica DISTO D410 820691... -
Page 4: Basic Measuring Screen
Instrument Set-up Basic measuring screen Selection screen Status bar FUNC Function / Settings Main line Active function Favorites Settings Help function Leica DISTO D410 820691... -
Page 5: Pointfinder (Viewscreen)
We recommend using high quality batteries. Change batteries when battery symbol is flashing. Illumination Crosshair adjustment with navigation keys left and right Zoom (1x, 2x, 4x) with navigation keys up and down Active function Favorites Leica DISTO D410 820691... -
Page 6: Operations
(min, max.). The last value measured is displayed in the main line. 2 sec Stops permanent / minimum- maximum measuring. 8.532 m Used to measure room diagonals (maximum val- ues) or horizontal distance (minimum values) Leica DISTO D410 820691... -
Page 7: Add / Subtract
Parallax errors occur when the pointfinder camera is used on close targets, with the effect that the laser appears dis- placed in the crosshair. In this case rely on the real laser dot. Leica DISTO D410 820691... -
Page 8: Settings
Settings Overview Distance units Beep Keypad lock Tilt calibration Favorites Illumination Offset Reset Information Leica DISTO D410 820691... -
Page 9: Distance Units
0.0 mm 0'00" 1/32 Beep ON/OFF Exit settings. To switch ON, repeat procedure. De-/Activate keylock Switch on with keylock To deactivate, repeat procedure. The keylock is active if device is switched off. within Exit settings. 2 sec Leica DISTO D410 820691... -
Page 10: Calibration Of Tilt Sensor (Tilt Calibration)
Place device on absolutely flat surface. and place it again on absolutely flat surface. After 2 sec the device 180° goes back to the basic mode. 180° Turn the device horizontally by 180° and place it again on absolutely flat surface. Leica DISTO D410 820691... -
Page 11: Personalized Favorites
Function is set as Exit settings. Select favorite selection-key in favorite above the function. the measuring corresponding se- mode. lection key. Illumination To save power re- duce bright- ness if not necessary. Exit settings. Confirm setting. Select brightness. Leica DISTO D410 820691... -
Page 12: Offset
The offset icon is Exit settings. displayed. Reset Second confirmation with selection keys: Reset returns the instrument to the factory settings. All custom- Refuse: Confirm: ized settings and memories are lost. Exit settings. Leica DISTO D410 820691... -
Page 13: Functions
Stake out Adjusting measuring reference Pythagoras 1 Memory Single Distance Measurement Smart Horizontal Mode Area Timer The self release starts if ON/Measure key is pressed. 30 sec Confirm setting. Select release 5 sec time. 2 sec Leica DISTO D410 820691... -
Page 14: Adjusting Measuring Reference/Tripod
Functions Adjusting measuring reference/tripod Distance is measured from the rear of the device (standard setting). Distance is measured from a Leica DISTO Adapter FTA 360 (lock symbol = perma- nently) Distance is measured from the tripod thread permanently. Distance is measured from the front of the device (lock symbol = permanently). -
Page 15: Memory
Aim active laser at target. creases. Smart Horizontal Mode 40.8 ° 5.204 m 0.032 m 4.82 7 m Aim laser at (up to 360° and a transverse target. tilt of ±10°) Leica DISTO D410 820691... -
Page 16: Area
Partial Measurements / Painter function: 3.9I0 m Second distance Press + or - before starting the first measure- ment. Measure and add or subtract distanc- 20.276 m Circumference es. Finish with =. Measure 2nd length. 24.3 52 m Area Leica DISTO D410 820691... -
Page 17: Volume
Use Up/Down 5.744 m 13.430 m First distance Ceiling/floor area navigation keys to show more re- 2.338 m 39.300 m Second distance Wall areas sults. 2.431 m 16.164 m Third distance Circumference 32.6 53 m Volume Leica DISTO D410 820691... -
Page 18: Stake Out
The distance to The function can be stopped the next stake out 0.625 m by pressing the CLEAR/OFF point is displayed. button. 0.24 0 m Approve value "b" and start meas- urement. Leica DISTO D410 820691... -
Page 19: Pythagoras (2-Point)
Minimum or Maximum measure- ment. 21.383 m We recommend to use the pythagoras only for indirect 13.2 07 m horizontal measuring. For height measuring (vertical) it is more precise to use a function with the inclination measuring. Leica DISTO D410 820691... -
Page 20: Technical Data
5.6 x 2.28 x 1.14 in Weight (with batteries) 198 g / 6.37 oz Temperature range: - Storage -25 to 70 °C -13 to 158 °F - Operation -10 to 50 °C 14 to 122 °F Leica DISTO D410 820691... -
Page 21: Message Codes
Hold the instrument Warranty coverage for the entire usage time Heinrich-Wild-Strasse than 10° without any transverse tilt. of the product according to Leica Geosys- CH-9435 Heerbrugg Calibration mistake Make sure, the device is tems International Limited Warranty. Free of placed on a absolutely Internet: www.disto.com... -
Page 22: Permitted Use
• Aiming directly in the sun Leica DISTO D410 820691... -
Page 23: Electromagnetic Compatibility (Emc)
Pulse repetition frequency 320 MHz It is a Class 2 laser product in accordance with: Pulse duration > 400 ps • IEC60825-1 : 2014 „Radiation safety of Beam divergence 0.16 x 0.6 mrad laser products“ Leica DISTO D410 820691... - Page 24 Leica Geosystems AG, Heerbrugg, Switzerland has been certified as being equipped with a quality system which meets the International Standards of Quality Management and Quality Systems (ISO standard 9001) and Environ- mental Management Systems (ISO standard 14001). Copyright Leica Geosystems AG, Heerbrugg,...