Martin Professional MAC 2000 Wash User Manual
  1. Manuals
  2. Brands
  3. Martin Professional Manuals
  4. Spotlight
  5. MAC 2000 Wash
  6. User manual

Martin Professional MAC 2000 Wash User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
MAC 2000 Wash
user manual

Advertisement

Table of Contents
loading

Related Manuals for Martin Professional MAC 2000 Wash

Summary of Contents for Martin Professional MAC 2000 Wash

  • Page 1 MAC 2000 Wash user manual...
  • Page 2 270° 270° © 2001-2004 Martin Professional A/S, Denmark. All rights reserved. No part of this manual may be reproduced, in any form or by any means, without permission in writing from Martin Professional A/S, Denmark. Printed in Denmark. P/N 35000114 Rev. H...

  • Page 3: Table Of Contents

    MAC 2000 Wash safety information ........

  • Page 4: Introduction

    The MAC 2000 Wash has a Fresnel lens fitted as standard, and is also supplied with a PC lens and a super-wide-angle lens. A motorized zoom provides beam angle ranges of 11° through to 40° (in the standard Fresnel configuration), 12°...
  • Page 5 • The exterior of the fixture can get very hot. Allow the fixture to cool for at least 5 minutes before handling. • Do not modify the fixture or install other than genuine Martin parts. • Do not operate the fixture if the ambient temperature (T ) exceeds 40°...

  • Page 6: Transportation

    RANSPORTATION Important! Release the transport locks before operating the fixture. Included items The MAC 2000 Wash is shipped in a cardboard box or in a 1 or 2 unit flight case that contains the following items. • User manual • 2 x 20 A main fuses (for use with 100-130 V local power supply) •...

  • Page 7: Double Flight Case

    Double flight case Unpacking 1 Open the flight case and pull the drawer all the way out. 2 Release the head (tilt) transport lock. 3 Install rigging hardware as described on page 11. 4 With one person on each side, lift the fixture out of the flight case.

  • Page 8: Ac Power

    Power supply The MAC 2000 Wash is shipped configured for 200 - 250 V at 50/60 Hz, but can be manually switched to accept either 100 - 130 V or 200 - 250 V power supplies.

  • Page 9: Fuses

    Install the appropriate fuses in the holders near the power switch. Power connection Important! Connect the MAC 2000 Wash directly to AC power. Do not connect it to a dimmer system; doing so may damage the fixture. You may need to install a cord cap that fits your supply on the power cable. A 3-prong grounding-type plug must be installed following the manufacturer’s instructions.

  • Page 10: Data

    Important! Never connect more than 1 data input and 1 data output. The MAC 2000 Wash has both 3-pin and 5-pin XLR sockets for DMX input and output. The pin-out on all sockets is pin 1 to shield, pin 2 to cold (-), and pin 3 to hot (+). There is no connection to pins 4 and 5.

  • Page 11: Rigging

    IGGING The MAC 2000 Wash can be placed on stage or clamped to a truss in any orientation. The Fast-Lock system enables quick and easy fastening of the clamp brackets in 4 positions as shown Figure 6. Figure 6: Clamp bracket positions Warning! Always use 2 clamps to rig the fixture.

  • Page 12: Control Panel

    Navigation The DMX address and any messages (see page 41) are displayed when the MAC 2000 Wash is turned on. To enter the menu, press [Menu]. Press [Up] and [Down] to move within the menu. To select a function or submenu, press [Enter].

  • Page 13: Readouts

    If tracking mode movement is not satisfactory there are 2 parameters that can be adjusted. The first is selected under P E R S / T R A C / M O d E . The default, M O d 1 , is the best choice with controllers that calculate intermediate positions at a steady rate.

  • Page 14: Service Messages

    Dimmer and zoom are calibrated to defined points. The other effects are calibrated relative to an arbitrary reference fixture. Default offset settings may be restored by selecting default offsets ( UT I L/ d FO F Calibrating effects 1 Apply power and strike the lamp. MAC 2000 Wash...
  • Page 15 2 To calibrate the zoom, select and press [Enter]. The default value of 128 can be U T IL /C A L/ Z OO F adjusted up or down to move the diffuser lens relatively forward or back. Make any necessary adjustments and press [Enter] to save the setting.

  • Page 16: Effects

    FFECTS The MAC 2000 Wash is compatible with USITT DMX512 controllers. The fixture has two DMX operating modes, 8-bit and 16-bit.16-bit mode requires two more DMX channels than 8-bit mode but provides more precise pan/tilt positioning. All other functions are identical. See “DMX protocol” on page 29.

  • Page 17: Beam Angles

    We have done this to cover the possibility that you rig and begin programming your MAC 2000 Wash and add barndoors to it later. If the DMX channels were not already assigned, you would have to re-patch your console and therefore would lose any programming already completed.
  • Page 18 In vector mode, speed is set directly on a speed channel. The cross-fade time must be 0. Vector control provides a way to set speed on controllers that do not have programmable fade times and results in smooth movement regardless of the cross-fade time or the controller’s processing power. MAC 2000 Wash...

  • Page 19: Optics

    PTICS This chapter describes the elements of the optical path and changes that can be made to them. It covers the: • Color wheel and filters, below • Front lenses, on page 21 • Aperture rings, on page 22 • Optional dimmer wheel, on page 22 Color wheels The following is a view of the color wheels as seen from the lamp.
  • Page 20 4 Remove the two screws holding the color wheel module in place using a Philips screwdriver. Disconnect the cables and lift the whole module out of the fixture. 29 / 28 Cable connections 5 Remove filters using your fingers and a soft cloth to protect the lens. MAC 2000 Wash...

  • Page 21: Changing The Front Lens

    8 Replace the fixture cover and apply power. Changing the front lens The MAC 2000 Wash has a Fresnel lens fitted as standard, and is also supplied with a PC lens, and a super-wide-angle lens. Note that when using the Fresnel lens the 50 mm (2 in) aperture ring provides the highest light output.

  • Page 22: Changing The Aperture Ring

    Changing the aperture ring The MAC 2000 Wash comes factory fitted with a 50 mm (2 in) aperture ring (identified by 5 small holes), and 3 optional rings: • 30 mm (1.2 in) - identified by 3 small holes • 40 mm (1.6 in) - identified by 4 small holes •...
  • Page 23 The dimmer wheel will be automatically detected by the MAC 2000 Wash when the fixture is powered on/reset. When the dimmer wheel is installed, the DMX channel 2 (Intensity) must be maintained at 100%.

  • Page 24: Routine Maintenance

    Disconnect the fixture from power before removing any cover. The lamp The MAC 2000 Wash comes with a double-ended lamp installed. This is one of two models: • Up to the middle of 2004 the lamp will be an OSRAM HMI 1200 W/S discharge lamp.

  • Page 25: Replacing The Lamp

    Replacing the lamp Important! Do not touch the quartz bulb with bare fingers. Replacement lamps are available from your Martin dealer. Please order: • OSRAM HMI 1200 W/S • Philips MSI 1200 The clear quartz bulb must be clean and free of any oils from your fingers.

  • Page 26: Cleaning

    4 Repeat step 2. Cleaning The MAC 2000 Wash requires routine cleaning. The schedule depends heavily on the operating environment; please consult a Martin service technician for recommendations. Important! Excessive dust, smoke fluid, and particle buildup degrades performance, leads to overheating and causes damage to the fixture that is not covered by the warranty.

  • Page 27: Firmware Installation

    LightJockey or DABS 1 interface) The following are required in order to install software: • The MAC 2000 Wash update file, available for download from the User Support Area of the Martin web site (http://www.martin.com). • The Software Uploader program, version 5.5 or later - supplied with the MUM, DABS1, Martin MP-2, LightJockey, or available for download from the support pages for these products in the User Support Area of the Martin web site.
  • Page 28 “NORM” position. Preventing firmware updates Firmware updates are enabled by default, but you can disable this by setting the Write jumper (see “Circuit board connections” on page 44) to disable. MAC 2000 Wash...

  • Page 29: Dmx Protocol

    PROTOCOL This section contains two DMX protocols (both apply to MAC 2000 Wash firmware version 1.7): • “16-bit protocol” on page 30 • “8-bit protocol” on page 33 The fixture is set up to use the 16-bit DMX protocol by default. To modify this, use the control menu. For more information see “Control menu”...

  • Page 30: 16-Bit Protocol

    Random color (if selected on channel 7) Normal (full range) 1 - 127 1 - 49 Minimum yellow setting (127 = full yellow) 128 - 254 50 - 99 Maximum yellow setting (128 = no yellow) Normal (full range) MAC 2000 Wash...
  • Page 31 DMX channel Value Percent Function (Start code=0) White → CTC 0 – 255 0 - 100 Color Wheel 1 (Multi Color) White White → Color 1,1 1 - 31 1 - 12 Color 1,1 Color 1,1 →Color 1,2 33 - 63 14 - 24 Color 1,2 Color 1,2 →...
  • Page 32 Tracking (Studio mode enabled – Overriding the MOdE menu setting) 246 – 248 97 - 98 Tracking (Shortcuts disabled - Overriding the SCUT menu setting) 249 – 251 Tracking (Shortcuts enabled - Overriding the SCUT menu setting) 252 – 255 No function MAC 2000 Wash...

  • Page 33: 8-Bit Protocol

    8-bit protocol DMX channel Value Percent Function (Start code=0) Shutter, Strobe, Reset, Lamp On/Off 0 - 19 0 - 7 Shutter Closed (lamp reduced to 700 W (E-ballast) after 10 sec.) NOTE! 20 - 49 8 - 19 No function (Shutter Open) Lamp Off is only allowed with Strobe on fast →...
  • Page 34 96 - 98 No Changes. 252 - 255 99 - 100 Open (Light buster mode) Barndoor 1 (Upper) Out → In 0 - 255 0 - 100 Barndoor 2 (Lower) Out → In 0 - 255 0 - 100 MAC 2000 Wash...
  • Page 35 DMX channel Value Percent Function (Start code=0) Barndoor 3 (Left) Out → In 0 - 255 0 - 100 Barndoor 4 (Right) Out → In 0 - 255 0 - 100 Rotate Barndoors Right → Center → Left (Center = 127) 0 - 255 0 - 100 MACRO functions (Barndoors)

  • Page 36: Control Menu

    ONTROL MENU This control menu applies to version 1.7 of the MAC 2000 Wash firmware. For the latest firmware updates, please visit the Martin web site at http://www.martin.com. Default values are in bold. Menu Item Options Notes (Default settings in bold print) DMX address.
  • Page 37 Decimal value of the DMX start code. The start code must be 0 d MX L S T CO for the MAC 2000 Wash to function properly. DMX value (from 0 - 255) received for each channel. d I M. . E F S P Reset fixture.
  • Page 38 Barndoor 4. Move in/out. Only available when barndoors are b4IO 0 - 255 installed. Pan - Left/Right 0-255 Tilt - Up/Down TILT 0-255 Run a general test of all effects T SE Q R U N MAC 2000 Wash...
  • Page 39 Menu Item Options Notes (Default settings in bold print) Enable pan/tilt position correction system. UTI L F E b A ( P r e ss Disable pan/tilt feedback. Setting not saved. O F F a nd ho l d E nt e r f or Enable on the fly reset of color wheels.

  • Page 40: Adjustment Submenu

    P NT d Pan neutral, tilt up. P NT U Pan left, tilt neutral. P LT N Pan right, tilt neutral. P RT N Pan left, tilt down. P LT d Pan right, tilt up. P RT U MAC 2000 Wash...

  • Page 41: Display Messages

    ISPLAY MESSAGES Message Appears when... What to do RST ( Reset) ... the fixture is indexing effects at Wait for reset to complete. startup. SR ST (Serial reset) ... the fixture has received a reset Wait for reset to complete. Set command from the controller.
  • Page 42 Message Appears when... What to do ...lamp temperature error. Set the fan speed to FULL using the LTE R UTIL menu and restart the fixture. Contact Martin service personnel if problem persists. Table 2: Display messages MAC 2000 Wash...

  • Page 43: Troubleshooting

    ROUBLESHOOTING Problem Probable cause(s) Remedy One or more of the fixtures No power to fixture. Check that power is switched on and cables is completely dead. are plugged in. Primary fuse blown (located near mains Disconnect fixture and replace fuse. inlet).

  • Page 44: Circuit Board Connections

    Color Wheel #1 PL 3 PL 9 Barn Door #3 / #4 Barn Door #3 / #4 Color Wheel #2 Color Wheel #2 PL 4 Barn Door Power Barn Door Power PL 15 PL 12 P/N 33120039-B MAC 2000 Wash...

  • Page 45: Specifications

    PECIFICATIONS Physical Length ..............408 mm (16.0 in) Width .
  • Page 46 Orientation ............... . any MAC 2000 Wash...
  • Page 47 MAC 2000 Wash E (in a cardboard packing case) ....... .

Table of Contents