ICP N9MP1 Service Manual page 33

Single Stage Multi Position Furnace
Figure 40
Downflow Installations (Single Pipe & Direct Vent N9MP1 & N9MP2(A1) Models)
LEFT Side Venting
Vent Fitting
Return Air
& Clamps
Combustion Blower
Mounting Screws (4)
5
/ ² ² ² ² Hose &
8
Clamps
Rubber
Plug
Plastic Caps
3
/ ² ² ² ² Hose & Clamps
4
Condensate
Trap & Gasket
Drain Line
Supply Air
Downflow Installations - (Single Pipe & Direct Vent N9MP1 & N9MP2 Models)
Mount the condensate drain trap in a vertical position to either the
right or left side of the furnace using the two screws and gasket that
are provided. If needed, remove the hole plugs from the furnace
side panel and relocated to the open set of holes in the opposite side
7
panel. Drill two / ² diameter holes in the casing using the conden-
64
sate trap as the template.
Ensure that the vent fitting and the 90° elbow is securely attached to
the combustion blower using the rubber coupling and clamps.
NOTE: The vent fitting MUST be installed with the airflow marking
arrow pointed toward the vent pipe, with the drain stub at a 20° to 30°
downward slope.
This configuration allows right side venting from the furnace. If the
left side venting is required, the combustion blower must be relo-
cated on the plastic transition box. Remove the four(4) screws that
secure the blower transition box. Rotate the blower 180° and secure
with the four(4) screws. Use caution to not over tighten the screws to
prevent stripping out of the plastic mounting holes.
Plug the upper drain stub on the vent fitting with the rubber plug. Use
a blunt pointed screwdriver to push the plug into the stub.
Remove the pressure switch hose from the upper stub on the plastic
transition.
RIGHT Side Venting
Pressure Switch
Combustion Blower
Hose, Transition
(Rotate 180° ° ° ° for Left Side)
Plastic
Pressure
Caps
Switch,
Transition
Transition Box
Pressure
Switch, Blower
Pressure Switch
Hose, Blower
Relocate the plastic caps on the stubs of the plastic transition box
from the lower stubs to the upper stubs and secure tightly with the
clamps.
Route the pressure switch hose to the lower drain stub on the plastic
transition box. Cut off excess hose and discard. Connect the pres-
sure switch hose to the lower stub on the plastic transition box.
NOTE: Failure to correctly install the pressure switch hose to the
transition can adversely affect the safety control operation.
Connect the
on the bottom of the plastic transition box and secure with a
clamp.
Route the hose to the large drain stub on the condensate trap. Cut
off excess hose and discard. Connect the hose to the drain stub on
the trap and secure with a
Connect the
on the vent fitting and secure with a
Route the hose to the smaller stub on the condensate trap. Cut off
excess hose and discard. Connect the hose to the drain stub on the
trap and secure with a
NOTE: Ensure hoses maintain a downward slope to the conden-
sate trap with no kinking or binding for proper condensate drainage.
31
Return Air
Vent Pipe
Grommet
Supply Air
dwg 25--23--60
(See Figure 40)
3
/ ² OD rubber hose with the 90° bend to the drain stub
4
3
/ ² clamp.
4
5
/ ² OD rubber hose with the 90° bend to the lower stub
8
3
5
/ ² clamp.
8
Service Manual
Combustion
Air Pipe,
N9MP2 ONLY
Vent Pipe
DRAIN SIDE VIEW
Rotate
downward
20° to 30°
3
/ ²
4
/ ² clamp.
4
440 08 2001 02