SPEED TRANSMITTER CHANGING THE BATTERY IN THE HEART RATE TRANSMITTER BELT WEARING THE HEART RATE TRANSMITTER STRAP INSTALLING THE CYCLOCOMUTER ON YOUR BIKE 10-14 PRO SCIO SERIES DISPLAY FIELDS MAIN OPERATING MODES 16-17 MEASURING WHEEL SIZE 18-19 PROGRAMMING THE CYCLOCOMPUTER...
Page 3
OPERATING THE STOPWATCH VIEWING LAP DATA TEMPERATURE MODE CADENCE MODE (PRO SCIO 3.3) HEART RATE MODE (PRO SCIO 4.1) ALTIMETER & POWER MODE (PRO SCIO 3.5 & 4.1) OPERATING THE EL/BACKLIGHT SYSTEM TROUBLESHOOTING FUNCTIONAL SPECIFICATIONS & RANGES WARRANTY & CONTACT o33_35_41_eng.indd 3...
Make sure the magnet and the transmitter are well aligned and check them regularly. PRO Scio Cyclecomputers are intended for use on bicycles only and should not be used on any motorized vehicle. Change the battery prior to failure to avoid data loss.
REPLACING THE BATTERY PRO Scio Cyclecomputers are powered by a CR2032 3v Lithium Battery. Under normal condi- tions, this battery should last approximately one year. REPLACING THE COMPUTER BATTERY Using a coin, turn the battery door counter clockwise until the door comes free.
CHANGING THE BATTERY IN THE WIRELESS SPEED TRANSMITTER - PRO SCIO The Wireless Speed Transmitter uses a 23A 12v Alkaline battery. Under normal conditions, this battery should last approximately one year. Using a coin, turn the battery door counter clockwise until the door comes free.
CHANGING THE BATTERY IN THE HEART RATE TRANSMITTER BELT - PRO SCIO 4.1 The PRO Scio 4.1 features a wireless heart rate transmitter, powered by a CR2032 3v Lithium battery. Under normal conditions you can expect to get approximately 700-800 hours of heart rate transmitter use with a fresh battery.
WEARING THE HEART RATE TRANSMITTER BELT - PRO SCIO 4.1 To ensure a proper heart rate display, the chest transmitter must be moistened and properly adjusted. Wet the elec- trodes (located to the right and left of the main transmitter case) with saliva or ECG conductive gel.
Page 10
PRO SCIO 3.3 MOUNTING THE WIRED CADENCE SENSOR On the PRO Scio 3.3, speed is picked up wirelessly from the front wheel and cadence is picked up via a wired connection from the crank arm. The wired cadence sensor is best installed starting with the cadence sensor unit and then working up toward the handlebar or stem bracket.
Page 11
INSTALLING THE CYCLOCOMPUTER ON YOUR BIKE - PRO SCIO 3.3 MOUNTING THE WIRED CADENCE SENSOR (continued) Route the sensor wire forward and under the bottom bracket and along the bottom of the down tube securing it occasionally with tape. Once you are near the head tube the sensor wire should be wrapped around the front or rear derailleur cable housing and the around the front brake cable housing.
INSTALLING THE CYCLOCOMPUTER ON YOUR BIKE INSTALLING THE WIRELESS FORK TRANSMITTER The PRO Scio 3.3, 3.5 and 4.1 receive speed and distance from a wireless transmitter mounted to the front fork. Attach the wireless front wheel sensor and rubber mounting pad to the front of the left fork blade using the zip-ties provided so the battery cap is pointing downward.
Page 13
INSTALLING THE CYCLOCOMPUTER ON YOUR BIKE INSTALLING THE WIRELESS FORK TRANSMITTER (CONTINUED) Adjust the position of the sensor and magnet so they are in proper alignment as shown. The magnet should pass by the sensor adjacent to the molded plastic line at a distance of 1-3mm.
Page 14
INSTALLING THE CYCLOCOMPUTER ON YOUR BIKE MOUNTING THE HANDLEBAR/STEM BRACKET Place the Cyclecomputer unit into the mounting bracket and turn clockwise until the unit snaps into place. When mounting the unit on the stem, you must first remove the 4 screws on the back of the mounting bracket and rotate it 90 degees. Replace the screws - do not overtighten.
PRO SCIO 3.3, 3.5 AND 4.1 DISPLAY FIELDS (PRO Scio 4.1) Indicates Heart Rate signal received Displays information specific to current operating mode Indicates current operating mode o33_35_41_eng.indd 15 11/21/07 12:25:42 P...
MAIN OPERATING MODES The PRO Scio 3.3 has 7 main operating modes. In all modes, Speed and Temperature and Ride Time are constant. Current operating mode is displayed in the lower display line. o33_35_41_eng.indd 16 11/21/07 12:25:50 P...
MAIN OPERATING MODES The PRO Scio 3.5 has 8 main operating modes. The PRO Scio 4.1 has 9 main operat- ing modes. In all modes, Speed and Ride Time are constant. Current operating mode is displayed in the lower display line.
MEASURING WHEEL SIZE DETERMINING YOUR WHEEL SIZE PRO Scio Computers use the rolling circumference of your wheel and tire combination to determine speed and distance. The more accurate this setting, the more accurate your ride information will be. However, variations of less than 30mm from the actual circumference will have very little impact on the overall accuracy of the unit.
MEASURING WHEEL SIZE MEASURING WHEEL SIZE USING ROLLOUT METHOD The roll-out method is the most accurate method for determining the circumference of your wheel/tire combination. On a flat open surface make a mark on your tire and the floor exactly where they meet.
PROGRAMMING THE CYCLECOMPUTER SELECTING MILES OR KILOMETERS, SETTING WHEEL SIZE AND ODMETER In Odometer Mode, Press & Hold the MODE key to enter the Setting Menu. There are 5 individual fields of information in the Odometer Setting Menu. Scroll through the fields by Pressing the OPTION or EL key.
PROGRAMMING THE CYCLECOMPUTER SET UNITS (MILES OR KILOMETERS) Press the MODE key. Adjust Miles or Kilometers by Pressing the OPTION or EL key. Set Units by Pressing the MODE key. Advance to next setting option by pressing OPTION or EL key. PRESS OPTION OR EL TO ADVANCE TO NEXT SETTING...
PROGRAMMING THE CYCLECOMPUTER SETTING WHEEL SIZE 1 & 2 Select Wheel Size 1 or 2 by pressing the OPTION or EL key. Press the MODE key. Scroll through pre-programmed wheel values by pressing the OPTION or EL key. Set wheel size by pressing the MODE key. PRESS OPTION OR EL TO ADVANCE TO NEXT SETTING...
PROGRAMMING THE CYCLECOMPUTER MANUALLY SETTING WHEEL SIZE Repeat steps 1-3 and continue to scroll through pre-programmed values until CUSTOM appears in the display. Press the SELECT key. The far left digit will begin to flash. Adjust digit by Pressing OPTION or EL key. Set value and advance to next digit by Pressing the SELECT key.
PROGRAMMING THE CYCLECOMPUTER SETTING ODOMETER PRO Scio Cyclocomputers allow you to manually program your odometers for both Bike 1 & 2. This is useful for preserving distance totals in the event of battery failure or if you need to reset the computer for any reason.
PROGRAMMING THE CYCLECOMPUTER SETTING TIME OF DAY PRO Scio Cyclecomputers display Time of Day in 1-minute resolution in 12 or 24-hour formats. In Time Mode, Press & Hold the MODE key to enter the Programming Sequence. Adjust 12 or 24-hour format by Pressing the OPTION or EL key.
PROGRAMMING THE CYCLECOMPUTER SETTING DISTANCE COUNTDOWN PRO Scio Cyclocomputers allow you to program a specific distance and count down to your specified destination in 1/100-mile/kilometer resolution. In Distance mode, Press the Option key to toggle between Distance Up and Down.
Page 27
PRO Scio Cyclocomputers estimate calories consumed during your ride. To calculate Calories you must enter your weight. you must also enter your weight to calculate Power/Wattage (PRO Scio 3.5, 4.1 only) In Stopwatch Mode, press & hold the Mode key to enter the Setting Menu. There are 2 individual fields of information in the Stopwatch Setting Menu.
PROGRAMMING THE CYCLECOMPUTER SETTING PERSONAL DATA In the Stopwatch Setting menu, select PERSONAL by pressing the Option or EL key. Press the Mode key. Adjust weight units (lbs or KG) by pressing the OPTION or EL key. Press MODE to set. Adjust Weight by pressing the OPTION or EL keys.
PROGRAMMING THE CYCLECOMPUTER SETTING THE STOPWATCH LAP FUNCTION PRO Scio Cyclecomputers are equipped with an advanced Lap Chronograph that allows you to time laps either manually or automatically based on either time or distance. In the Stopwatch Setting menu, select LAP by pressing the OPTION or EL key.
Page 30
PROGRAMMING THE CYCLECOMPUTER SETTING THE STOPWATCH LAP FUNCTION - AUTO LAP Auto LAP function automatically times laps based on either a pre-set time or distance. From the Lap Setting Menu, Select AUTO by pressing the Option or EL key. Press the MODE key.
SETTING HEART RATE TRAINING ZONE (PRO SCIO 4.1) The PRO Scio 4.1 allows you to set a target heart rate training zone in one beat per minute increments. The Stopwatch memory tracks time spent ABOVE, BELOW, and IN the target heart rate training zone that you have set for review after your workout.
PROGRAMMING THE CYCLECOMPUTER SETTING THE ALTIMETER (PRO SCIO 3.5 & 4.1) PRO Scio 3.5 & 4.1 have an advanced altimeter system that tracks distance ascent, distance descent and displays current altitude and current slope gradient. If miles are selected distance units, altimeter measurements will be in feet. If kilome- ters are selected, altimeter measurements will be in meters.
OPERATING THE CYCLOCOMPUTER SLEEP MODE To conserve battery life, when the Cyclecomputer does not receive a signal for a period of time, the unit goes into SLEEP mode. The display reads Time of Day in the center display line. All other display fields are blank.
OPERATING THE CYCLOCOMPUTER SELECT BIKE 1 OR BIKE 2 PRO Scio Cyclecomputers allow you to program two separate bike specifications. SWITCH FROM BIKE 1 TO BIKE 2 In Odometer (ODO) mode, press & hold the OPTION key to view Ododeter 2. (Release the OPTION key to resume Bike 1 settings.) Continue holding the OPTION key and press the SELECT key.
OPERATING THE CYCLOCOMPUTER DISTANCE TRAVELED / DISTANCE COUNTDOWN PRO Scio Cyclocomputers allow you to view both distance traveled and distance remaining to your destination. Once a Distance has been programmed (see page 26), activate Distance Countdown by pressing the SELECT key. The center line display segments (...
OPERATING THE CYCLOCOMPUTER OPERATING THE STOPWATCH PRO Scio Cyclocomputers are equipped with a lap Stopwatch that functions independently of Ride Data. In Stopwatch Mode, press the SELECT key to begin timing. MANUALLY TIMING LAPS While Stopwatch is running, press the SELECT key to STOP LAP timing. To begin another LAP, press the SELECT key again.
OPERATING THE CYCLOCOMPUTER VIEWING LAP DATA PRO Scio Cyclecomputers have an advanced memory that allows you to view detailed ride information by individual laps. With Stopwatch stopped, press the OPTION key begin the memory sequence. Scroll through individual lap data (starting with latest lap in descending order) by pressing the OPTION key.
OPERATING THE CYCLOCOMPUTER TEMPERATURE MODE Change Temperature units from °C (Celsius) to °F (Fahrenheit) by pressing & holding the MODE key in Temperature mode. PRESS & HOLD MODE PRESS & HOLD MODE o33_35_41_eng.indd 38 11/21/07 12:26:48 P...
OPERATING THE CYCLOCOMPUTER CADENCE MODE (PRO SCIO 3.3) In Cadence mode, toggle between Current Cadence and Average and Max cadence by pressing the OPTION key. PRESS OPTION PRESS OPTION o33_35_41_eng.indd 39 11/21/07 12:26:49 P...
OPERATING THE CYCLOCOMPUTER HEART RATE MODE (PRO SCIO 4.1 ONLY) When the PRO Scio 4.1 is receiving a heart rate signal, Heart Rate icon ( ) will display above the Temperature field. The Target Zone arrows ( ) indicate whether current heart rate is above or below Target Zone.
OPERATING THE CYCLOCOMPUTER ALTIMETER MODE (PRO SCIO 3.5 & 4.1) The PRO Scio 3.5 and 4.1 have 4 Altimeter sub modes. Scroll through Altimeter modes by pressing the OPTION key. CURRENT ALTITUDE VERTICAL ASCENT VERTICAL DESCENT CURRENT GRADIENT POWER MODE (PRO SCIO 3.5 & 4.1) The PRO Scio displays your current Power/Wattage output based on rider weight, current speed and current gradient.
OPERATING THE CYCLOCOMPUTER OPERATING THE EL/BACKLIGHT SYSTEM PRO Scio cyclecomputers are equipped with an EL/Backlight for viewing in low light conditions. Press the EL key to iluminate the display for approximately 5 seconds. Excessive use of backlight will reduce baterry life.
TROUBLESHOOTING Battery is weak and must be replaced. Change the battery or reset the computer. Reset the computer. Check sensor/magnet alignment. Make sure that the sensor is no more than 3mm from the magnet. Unit may have been over exposed to direct sunlight. Move the bike to the shade.
For more information or specific details regarding claims against this warranty please contact your local dealer or search for your local PRO dealer or distributor in the Dealer Locator on the official PRO website (http://www.pro-bikegear.com).
Page 47
DIGI / PACE SERIES APEX SERIES Item Limit X-1.6 W-2.1 W-2.9 RPM W-3.5 Alti W-4.0 Alti-HR Limit Speed Snelheid Vitesse Geschwindigkeit Velocità Velocidade Velocidad Скорость スピード 0.0 – 199.9 Km/h or 120.0 Mile/h +/- 1% WIRED ANALOG W/L ANALOG W/L ANALOG W/L ANALOG W/L 199.9Km/h or m/h...
Page 48
DIGI / PACE SERIES APEX SERIES Item W7 W12 WR Limit X-1.6 W-2.1 W-2.9 RPM W-3.5 Alti W-4.0 Alti-HR Limit Speed 0.0 – 199.9 Km/h or 120.0 Mile/h +/- 1% WIRED ANALOG W/L ANALOG W/L ANALOG W/L ANALOG W/L 199.9Km/h or m/h No.