Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Pro Scio X-1.6
Summary of Contents for Pro Scio X-1.6
- Page 1 ENGLISH PRO SCIO X-1.6 & W-2.1 Jet12_15.indd 1 10/11/07 6:47:47 P...
-
Page 2: Table Of Contents
TABLE OF CONTENTS WARNINGS & CAUTIONS COMPONENTS OF THE CYCLECOMPUTER REPLACING THE BATTERY CHANGING THE BATTERY IN THE WIRELESS SPEED TRANSMITTER INSTALLING THE CYCLOCOMUTER ON YOUR BIKE 8-12 KEYS & THEIR FUNCTIONS MAIN OPERATING MODES 14-15 MEASURING WHEEL SIZE 16-17 PROGRAMMING THE CYCLOCOMPUTER SELECTING MILES OR KILOMETERS SETTING WHEEL SIZE... - Page 3 TABLE OF CONTENTS OPERATING THE CYCLOCOMPUTER SLEEP MODE RESETTING THE UNIT SELECT BIKE 1 OR BIKE 2 DISTANCE TRAVELED / DISTANCE COUNTDOWN OPERATING THE STOPWATCH CENTERLINE SEGMENT DISPLAY TROUBLESHOOTING FUNCTIONAL SPECIFICATIONS & RANGES WARRANTY & CONTACT Jet12_15.indd 3 10/11/07 6:47:47 P...
-
Page 4: Warnings & Cautions
Make sure the magnet and the transmitter are well aligned and check them regularly. PRO Scio Cyclecomputers are intended for use on bicycles only and should not be used on any motorized vehicle. Change the battery prior to failure to avoid data loss. -
Page 5: Components Of The Cyclecomputer
COMPONENTS OF THE CYCLECOMPUTER (SCIO W-2.1 ONLY) (SCIO W-2.1 ONLY) (SCIO W-2.1 ONLY) (SCIO X-1.6 ONLY) Jet12_15.indd 5 10/11/07 6:47:49 P... -
Page 6: Replacing The Battery
REPLACING THE BATTERY PRO Scio Cyclecomputers are powered by a CR2032 3v Lithium Battery. Under normal condi- tions, this battery should last approximately one year. REPLACING THE COMPUTER BATTERY Using a coin, turn the battery door counter clockwise until the door comes free. -
Page 7: Changing The Battery In The Wireless Speed Transmitter
CHANGING THE BATTERY IN THE WIRELESS SPEED TRANSMITTER The Wireless Speed Transmitter uses a 23A 12v Alkaline battery. Under normal conditions, this battery should last approximately one year. Using a coin, turn the battery door counter clockwise until the door comes free. Take care not to damage the O-ring seal for the battery compartment and carefully remove the old battery. -
Page 8: Installing The Cyclocomuter On Your Bike
INSTALLING WIRED FRONT WHEEL SPEED SENSOR AND BRACKET The PRO Scio X-1.6 uses a single wired sensor attached to the front fork. Attach the front wheel sensor to either fork blade using the zip-ties provided. Snug up the zip-ties but do not fully tighten them. - Page 9 INSTALLING THE WIRED CYCLECOMPUTER ON YOUR BIKE - PRO SCIO X-1.6 INSTALLING WIRED FRONT WHEEL SPEED SENSOR AND BRACKET (continued) Route the remaining wire and bracket up the fork securing it with tape. Excess wire should be wrapped around the brake cable housing until there is just enough slack remaining to allow the bracket to be attached to the handlebars.
- Page 10 INSTALLING THE WIRELESS CYCLECOMPUTER ON YOUR BIKE - PRO SCIO W-2.1 INSTALLING THE WIRELESS FORK TRANSMITTER The PRO Scio W-2.1 receives speed and distance from a wireless transmitter mounted to the front fork. Attach the wireless front wheel sensor and rubber mounting pad to the front of the left fork blade using the zip-ties provided so the battery cap is pointing downward.
- Page 11 INSTALLING THE WIRELESS CYCLECOMPUTER ON YOUR BIKE - PRO SCIO W-2.1 INSTALLING THE WIRELESS FORK TRANSMITTER (CONTINUED) Adjust the position of the sensor and magnet so they are in proper alignment as shown. The magnet should pass by the sensor adjacent to the molded plastic line at a distance of 1-3mm.
- Page 12 INSTALLING THE WIRELESS CYCLECOMPUTER ON YOUR BIKE MOUNTING THE HANDLEBAR/STEM BRACKET Place the Cyclecomputer unit into the mounting bracket and turn clockwise until the unit snaps into place. When mounting the unit on the stem, you must first remove the 4 screws on the back of the mounting bracket and rotate it 90 degees.
-
Page 13: Keys & Their Functions
KEYS & THEIR FUNCTIONS MODE KEY SET KEY modes Programming Sequence in Average Speed mode Distance Mode Programming Sequence during operation Jet12_15.indd 13 10/11/07 6:47:58 P... -
Page 14: Main Operating Modes
MAIN OPERATING MODES The PRO Scio X-1.6 and PRO Scio X-2.1 have 7 main operating modes. Scroll through modes key. 12_15.indd 14 10/11/07 6:48:02 PM... - Page 15 MAIN OPERATING MODES SCAN MODE The PRO Scio X-1.6 and PRO Scio X-2.1 can be programmed to automatically scan though all operating modes in 2-second intervals. To activate Scan mode, key for 2 seconds in any operating mode. To deactivate Scan mode, key.
-
Page 16: Measuring Wheel Size
MEASURING WHEEL SIZE DETERMINING YOUR WHEEL SIZE PRO Scio Computers use the rolling circumference of your wheel and tire combination to determine speed and distance. The more accurate this setting, the more accurate your ride will have very little impact on the overall accuracy of the unit. - Page 17 MEASURING WHEEL SIZE MEASURING WHEEL SIZE USING ROLLOUT METHOD The roll-out method is the most accurate method for determining the circumference of your On a flat open surface make a mark on your tire and the floor exactly where they meet.
-
Page 18: Programming The Cyclocomputer
PROGRAMMING THE CYCLECOMPUTER SELECTING MILES OR KILOMETERS, SETTING WHEEL SIZE AND ODMETER The main Programming Sequence calibrates the computers measurments for both Bikes 1 and 2. In order to assure accuracy of the unit, all fields of information must be programmed. SELECTING MILES OR KILOMETERS advance to set Wheel Size. -
Page 19: Setting Wheel Size
PROGRAMMING THE CYCLECOMPUTER SETTING WHEEL SIZE Adjust wheel circumference of Bike 1 starting with right through left digits (digit being adjust will blink). Adjust blinking digit by pressing the Set key. Set digit and advance to next by Pressing the Mode key. Once all fields have been adjusted, Press the Mode key to advance to adjust wheel circumference for Bike 2. -
Page 20: Setting Odometer
PROGRAMMING THE CYCLECOMPUTER SETTING ODOMETER PRO Scio Cyclecomputers allow you to manually program your odometer. This is useful for preserving distance totals in the event of battery failure or if you need to reset the computer for any reason. Set Odometer of Bike 1 starting with right through left digits (digit being adjust will blink). -
Page 21: Setting Time Of Day
PROGRAMMING THE CYCLECOMPUTER SETTING TIME OF DAY PRO Scio Cyclecomputers display Time of Day in 1-minute resolution in 12 or 24-hour formats. Adjust 12 or 24-hour format by Pressing the Set key. Set format and advance to set time by Pressing the Mode key. -
Page 22: Setting Distance Countdown
PROGRAMMING THE CYCLECOMPUTER SETTING DISTANCE COUNTDOWN resolution and count down to your specified destination. In Distance mode, Press the Set key to toggle between Distance Up and Down. The Distance Countdown icon ( ) will appear in the center line of the display. Sequence. -
Page 23: Setting Calories Information
PROGRAMMING THE CYCLECOMPUTER SETTING CALORIES INFORMATION (STOPWATCH MODE) PRO Scio Cyclecomputers estimate calories consumed during your ride. To calculate Calories you must enter your weight. Adjust weight units (pounds or kilograms) by Pressing the Set key. Select pounds or kilograms and advance to set weight by Pressing the Mode key. -
Page 24: Operating The Cyclocomputer
OPERATING THE CYCLECOMPUTER SLEEP MODE To conserve battery life, when the Cyclecomputer does not receive a signal for a period of time, the unit goes into SLEEP mode. The display reads Time of Day in the lower display line. All other display fields are blank. -
Page 25: Select Bike 1 Or Bike 2
OPERATING THE CYCLECOMPUTER SELECT BIKE 1 OR BIKE 2 PRO Scio Cyclecomputers allow you to program two separate bike specifications. Most functions are totally independent. For example, you can program Bike One for Speed and Jet12_15.indd 25 10/11/07 6:48:15 P... -
Page 26: Distance Traveled / Distance Countdown
OPERATING THE CYCLECOMPUTER DISTANCE TRAVELED / DISTANCE COUNTDOWN PRO Scio Cyclecomputers allow you to view both distance traveled and distance remaining to your destination. Once a Distance has been programmed, activate Distance Countdown by Pressing both the Mode and Set keys. The center line display segments (... -
Page 27: Operating The Stopwatch
OPERATING THE CYCLECOMPUTER OPERATING THE STOPWATCH PRO Scio Cyclecomputers are equipped with a 20-hour Stopwatch that operates indepen- dantly of Ride Time (ATM). In Stopwatch Mode, Press the Set key to begin timing. Press Set to stop timing. When Stopwatch is stopped, the display will cycle between Elapsed Time and Calories Consumed in 2-second intervals. -
Page 28: Centerline Segment Display
OPERATING THE CYCLECOMPUTER PRO SCIO SERIES DISPLAY FIELDS See page 15 See page 26 Displays information specific to current operating Indicates current operating mode, including Ride Time mode and Stopwatch, Distance, Time of Day, Average Speed and Max Speed 12_15.indd 28... -
Page 29: Troubleshooting
TROUBLESHOOTING Battery is weak and must be replaced. Change the battery or reset the computer. Reset the computer. the sensor is no more than 3mm from the magnet. Unit may have been over exposed to direct sunlight. Move Distance between magnet and transmitter is too great (3 mm maximum). -
Page 30: Functional Specifications & Ranges
FUNCTIONAL SPECIFICATIONS & RANGES TIME OF DAY SPEED formats STOPWATCH ODOMETER TRIP WHEEL SIZE millimeters 12_15.indd 30 10/11/07 6:48:18 PM... -
Page 31: Warranty & Contact
For more information or specific details regarding claims against this warranty please contact your local dealer or search for your local PRO dealer or distributor in the Dealer Jet12_15.indd 31 10/11/07 6:48:19 P... - Page 32 Industrieweg 24 8071 CT Nunspeet The Netherlands 12_15.indd 32 10/11/07 6:48:19 PM...
- Page 33 DIGI / PACE SERIES APEX SERIES Item Limit X-1.6 W-2.1 W-2.9 RPM W-3.5 Alti W-4.0 Alti-HR Limit Speed Snelheid Vitesse Geschwindigkeit Velocità Velocidade Velocidad Скорость スピード 0.0 – 199.9 Km/h or 120.0 Mile/h +/- 1% WIRED ANALOG W/L ANALOG W/L ANALOG W/L ANALOG W/L 199.9Km/h or m/h...
- Page 34 DIGI / PACE SERIES APEX SERIES Item W7 W12 WR Limit X-1.6 W-2.1 W-2.9 RPM W-3.5 Alti W-4.0 Alti-HR Limit Speed 0.0 – 199.9 Km/h or 120.0 Mile/h +/- 1% WIRED ANALOG W/L ANALOG W/L ANALOG W/L ANALOG W/L 199.9Km/h or m/h No.
Need help?
Do you have a question about the Scio X-1.6 and is the answer not in the manual?
Questions and answers