Arming Mode “Vacation”; Maximum Arming For The First Partition - SECOLink MAS-800 Short User Manual

Intruder alarm system
Arming the first partition with entry delay on – A1A
Only the first partition is armed. This kind of arming is available in
floor isn't used
The second or both partitions can be armed with A
ž F-key: for EU countries –
ž Via Menu:
Arming mode "Night" – C
This arming mode is used
The interior zones are left disarmed, if anyone opens door, won't be the entry delay and the alarm will sound.
This arming mode is effective, when the door and windows are secured by the opening sensors or there are
installed glass break detectors. Arming:
ž F-key:
ž Via Menu:
Forced Arming – F , AAAA
The arming mode, that allows to arm the system when the zones are violated or the sensor is broken. All
sensors, which were remained earlier, will be armed. After opening the entry/exit door the system will give
entry delay time. Arming:
ž F-key:
ž Via Menu:
Partial Arming
This is universal way of arming, which enables to arm selected partition in desired arming mode. In case of
partial arming Green LED will blink slowly.
ž1 example:
ž 2 example:
1 example 2 example
Arming and disarming of security barrier, "Pre-alarm" mode
Microwave or infrared rays based security barriers, also outdoor PIR detectors, which are connected to the
system, can be armed by "Pre-alarm" mode. The system will sound an alarm (without sending alarm
message to Central Monitoring Station), when someone travers this electrical barrier. The "Pre-alarm"
mode can be turned on and turned off the same way, as described below. For the more convenient control
of "Pre-alarm" is recommended to create special F-keys (during installation process).
ž Via Menu:
Bypassing zone – B
If you want to arm the system with zones, which are violated (for example: with opened windows) it's
necessary to determine, that the system bypass these zones. Bypass procedure can be made:
F-key:
ž
ž Via Menu:
The zone, which you want to bypass is selected with
bypassed, the symbol
one arming/disarming cycle.
Abort arming
For selecting, also for aborting arm procedure the system SECOLink has the
want to abort arming, press the
Arming system with troubles
EU standards unexpect
alarm
impossible in the ways, which were discribed earlier. It is necessary immediately eliminate troubles, also
inform CMS and company, which had installed the system.The system detects troubles in own modules,
armed
also it detects and other common troubles, like
because of repair
trouble
time and arm system as usual. It can be done this way:
Press the
3 CLR
Yellow "Trouble" LED starts to blink fast. The blinking duration is
make usual arming procedure.
, all sensors of this partition are armed. When somebody opens doors will be an entry delay.
A 1
, [Arming]
ENT ENT
when you want to arm the system with the person staying inside of the premise.
for EU countries –
C
, [Arming] , [Night]
ENT ENT
for EU countries –
F
, [Arming]
ENT ENT
, [Arming] , [Vacation]
ENT ENT
, [Arming]
ENT ENT
, [Prealarm]
ENT
, [PIN:]
B ENT PIN:
, [Zone Bypass]
ENT
Zone isn't
violated
will be shown on display. Bypass procedure is finishing by the ENT key. The zone is bypassing for
key, enter PIN and confirm it with the
CLR
using of the system, which has troubles. When Yellow LED is on, the arming is
, battery discharge. In exceptional cases is possible to bypass the troubles for a short
key once - message about the trouble will be shown on the display, then press
CLR
2A or A12A respectively
, for
non EU countries is available
A ENT PIN: ENT
, [Away] , [PIN:]
ENT
, for
non EU countries is available
ENT PIN: ENT
, [PIN:]
ENT PIN: ENT
, for
non EU countries is available
ENT PIN: ENT
, [Forced Arming]
, [PIN:]
ENT PIN:
, [Away] , [PIN:]
ENT PIN:
, [PIN:]
ENT PIN: ENT
:
ENT
, [PIN:]
ENT
Zone is
violated
or keys, and is marked the
230V disappearance in AC line, disconnected phone line
2-storied house , when at night the ground
. Arming :
, [Parts:]
PIN: ENT ENT
, [Parts:] .
ENT
, [PIN:] .
ENT PIN: ENT
, [Parts:]
ENT ENT
, [Parts:]
ENT
, [Parts:] .
ENT
:
PIN: ENT
key. If selected zone is
key. If the exit delay is in process and you
CLR
key.
ENT
30 seconds, during this time is possible to
Short user manual
.
A 1 A ENT
.
.
C ENT
.
F ENT
.
ENT
Zone is
bypassed
key again -
CLR