Advertisement
Quick Links
Instruction Manual
REMOTE
POWER
ALARM
Data, drawings, and other material contained herein are proprietary to Cross Technologies, Inc.,
but may be reproduced or duplicated without the prior permission of Cross Technologies, Inc.
for purposes of operating the equipment. Printed in USA.
When ordering parts from Cross Technologies, Inc., be sure to include the equipment
model number, equipment serial number, and a description of the part.
1350-1700>
MENU
1800-2150 G= 10
EXECUTE
C
T
ROSS
ECHNOLOGIES, INC.
6170 Shiloh Road
Alpharetta, Georgia 30005
(770) 886-8005
FAX (770) 886-7964
Toll Free 888-900-5588
WEB www.crosstechnologies.com
E-MAIL info@crosstechnologies.com
Model 2083-1721
Agile L to L Translator
MODEL 2083
TRANSLATOR
August 2009 Rev A
C
T
ROSS
ECHNOLOGIES INC.
Advertisement
Related Manuals for Cross Technologies 2083-1721
Summary of Contents for Cross Technologies 2083-1721
- Page 1 ALARM Data, drawings, and other material contained herein are proprietary to Cross Technologies, Inc., but may be reproduced or duplicated without the prior permission of Cross Technologies, Inc. for purposes of operating the equipment. Printed in USA. When ordering parts from Cross Technologies, Inc., be sure to include the equipment model number, equipment serial number, and a description of the part.
-
Page 2: Table Of Contents
All Cross Technologies, Inc. products are warranted against defective materials and workmanship for a period of one year after shipment to customer. Cross Technologies, Inc.’s obligation under this warranty is limited to repairing or, at Cross Technologies, Inc.’s option, replacing parts, subassemblies, or entire assemblies. Cross Technologies, Inc. shall not be liable for any special, indirect, or consequential damages. -
Page 3: General
DC power is applied (green) or a PLL alarm occurs (red). Connectors are BNC female for RF input and output and for (optional) external 10 MHz reference (+3± 3 dBm in). The 2083-1721 is housed in an 1 3/4” X 19” X 16”... -
Page 4: Technical Characteristics
1.2 Technical Characteristics TABLE 1.0 2083-1721 Frequency Translator Specifications* Input Characteristics Input Impedance/RL /12 dB Frequency, 1350-1700 MHz Input Level -10 to -30 dBm Input 1 dB compression 0 dBm Output Characteristics Impedance/RL 75 /12 dB Output Level, Range -10 to -30 dBm... -
Page 5: Monitor & Control Interface
Not Used Alarm Relay: Normally Closed B) Status Requests - Table 1.1 lists the status requests for the 2083-1721 and briefly describes them. PLEASE NOTE: The two character {aa}(00-31) prefix, in the table below, should be used ONLY when RS-485, (OPTION-Q), is selected. - Page 6 C) Commands Table 1.2 lists the commands for the 2083-1721 and briefly describes them. After a command is sent the 2083 sends a return “>” indicating the command has been received and executed. General Command Format - The general command format is {CND...}, where:...
-
Page 7: Installation
2.1 Mechanical The 2083-1721 consists of one RF/Controller PCB housed in a 1 RU (1 3/4 inch high) by 16 inch deep chassis. A switching, ± 12, +24, +5 VDC power supply provides power for the assemblies. The 2083-1721 can be secured to a rack using the 4 holes on the front panel. - Page 8 -10 to -30 dBm input 75 BNC female connector. 75 ohms, BNC female connector. 100-240 ±10% VAC, see Table 2.2. 47-60 Hz. FIGURE 2.1 2083-1721 Rear Panel I/O s TABLE 2.1 J10 Pinouts* TABLE 2.1 J J 10 Function Rx+ (RS-232C) Tx+ (RS-232C) TABLE 2.2 I I nput/Output...
- Page 9 2.4 Installation / Operation 2.4.1 Installing and Operating the 2083-1721, Frequency Translator Section 1. Connect a -10 dBm to -30 dBm signal to IN, J4 (Figure 2.1) 2. Connect the OUT, J5, to the external equipment 3. Connect 100-240 ±10% VAC, 47 - 63 Hz to AC connector on the back panel.
- Page 10 If programming is initiated and no operator action takes place for approximately 12 seconds (before the final press of the Menu/Execute switch) the display will revert to its previous status and you will need to start over. 2083-1721 Manual, Rev.A Page 10 8/27/09...
- Page 11 During frequency , gain changes, the vertical movement will raise or lower the number in the direction of the arrows. b. For other functions such Remote on/off, the vertical switch will alternately turn the function on or off regardless of the direction operated. 2083-1721 Manual, Rev.A Page 11 8/27/09...
- Page 12 “R”, push the Menu/Execute switch to get to: SAVE SETTINGS? Selecting Y will save the new settings. Selecting N will revert to the previous settings. Figure 2.4 gives the menu items and how to make changes 2083-1721 Manual, Rev.A Page 12 8/27/09...
-
Page 13: Operation
(option -Q) SCROLL <> ADDRESS = 00 Menu 6 Set RS-485 Address SCROLL PUSH BUTTON (option -Q) SAVE SETTINGS? Save? When go to end SCROLL <> PUSH BUTTON FIGURE 2.4 Menu Display and Sequences 2083-1721 Manual, Rev.A Page 13 8/27/09... -
Page 14: Environmental Use Information
G. Top Cover - There are no serviceable parts inside the product so, the Top Cover should not be removed. If the Top Cover is removed the ground strap and associated screw MUST BE REINSTALLED prior to Top Cover screw replacement. FAILURE TO DO this may cause INGRESS and/or EGRESS emission problems. 2083-1721 Manual, Rev.A Page 14 8/27/09... -
Page 15: Shiloh Road Alpharetta, Georgia
ROSS ECHNOLOGIES, INC. 6170 Shiloh Road Alpharetta, Georgia 30005 (770) 886-8005 FAX (770) 886-7964 Toll Free 888-900-5588 WEB www.crosstechnologies.com E-MAIL info@crosstechnologies.com 2009 Printed in USA • 2083-1721 Manual, Rev.A Page 15 8/27/09...
Need help?
Do you have a question about the 2083-1721 and is the answer not in the manual?
Questions and answers