Sanyo PLC-XU106 Service Manual page 45

Electrical Adjustments
Group/
Item Name
Item
3 GAIN AREA V START
4 Image AREA H WIDTH
5 Image AREA V HIGHT
6 OFFSET target
7 OFFSET torelance
8 GAIN target
9 GAIN torelance
Group
Auto calibration (cVBS/SVIdeo)
262
0 Y Image Area Start X
1 Y Image Area Start Y
 Cb Image Area Start X
3 Cb Image Area Start Y
4 Cr Image Area Start X
5 Cr Image Area Start Y
6 Image Area H Width
7 Image Area V Hight
8 Y Target Level
9 Cb Target Level
10 Cr Target Level
11 Gain Tolerance
1 Delta Gain
Group
Auto calibration (Ycbcr)
264
0 Y-OFFSET AREA H START
1 Y-OFFSET AREA V START
CB - OFFSET AREA H

START
CB - OFFSET AREA V
3
START
CR - OFFSET AREA H
4
START
CR - OFFSET AREA V
5
START
6 Y - GAIN AREA H START
7 Y - GAIN AREA V START
8 CB - GAIN AREA H START
9 CB - GAIN AREA V START
10 CR - GAIN AREA H START
11 CR - GAIN AREA V START
1 Image AREA H WIDTH
13 Image AREA V HIGHT
14 Y - OFFSET TARTGET
15 CB OFFSET TARGET
16 CR OFFSET TARGET
17 Y - GAIN TARGET
18 CB - GAIN TARGET
19 CR - GAIN TARGET
0 OFFSET torelance
1 GAIN torelance
Group
AutoPc Adjsut
280
0 AutoPCAdjustEnable
1 Frequency Step
 Frequency Threshold
3 Fine Phase
4 BLKDET
5 PHASEMSK
Group
Paneltype * Panel type check
290
Function
White Level Acquiring Area V-Start
Position
Black/White Level Acquiring Area
Black/White Level Acquiring Area
Height
Target Value of Black Level Adj.
Torelance of Black Level Adj.
Target Value of White Level Adj.
Torelance of White Level Adj.
Y Acquiring Area H-Start Position
Y Acquiring Area V-Start Position
Cb Acquiring Area H-Start Position
Cb Acquiring Area V-Start Position
Cr Acquiring Area H-Start Position
Cr Acquiring Area V-Start Position
Image Level Acquiring Area
Image Level Acquiring Area Height
Target Value of Y Level Adj.
Target Value of Cb Level Adj.
Target Value of C Level Adj.
Torelance of Level Adj.
Deviation Width of Gain Value
Y - Offset Acquiring Area H-Start
Position
Y - Offset Acquiring Area V-Start
Position
CB - Offset Acquiring Area H-Start
Position
CB - Offset Acquiring Area V-Start
Position
CR - Offset Acquiring Area H-Start
Position
CR - Offset Acquiring Area V-Start
Position
YCBCR Level Acquiring Area
YCBCR Level Acquiring Area Height
Torelance of OFFSET Adj.
Torelance of GAIN Adj.
Auto-PC Adj Operation Enable if Un-
supported Signal Input
Frequency Steps of TotalDot
Total Dot Freqency Threshold
Do Phase Adj after Total Dot Adj.
Black Level Detection Area
Phase Detection Filter
Initial
500
13
9
3
1
38
1
0
00
500
500
500
500
8
9
17
17
17
1
9
95
500
95
500
95
500
50
500
800
500
700
500
8
9
4
18
18
17
37
37
1
1
0
1
5
1
1
0
-45-
range Note
0 - 1000
0 - 4095
0 - 4095
0 - 17
1 - 17
0 - 55
1 - 55
0 - 1000
0 - 1000
0-1000
0-1000
0-1000
0-1000
0 - 4095
0 - 4095
0 - 55
0-55
0-55
0 - 55
0 - 55
0 - 1000
0 - 1000
0 - 1000 If not used: use Y's value
0 - 1000 If not used: use Y's value
0 - 1000 If not used: use Y's value
0 - 1000 If not used: use Y's value
0 - 1000
0 - 1000
0 - 1000
0 - 1000
0 - 1000
0 - 1000
0 - 4095
0 - 4095
0 - 55
0 - 55
0 - 55
0 - 55
0 - 55
0 - 55
1 - 55
1 - 55
0 - 1 0: Enable, 1: Disable
0-3
0 - 10 0 [] <--- -----> 10[Not matched]
0: Executes Fine Phase, 1: Not
0 - 1
Execute
0 - 3
0: Effective All Bit,
1: Disable Lower 1 bit
0 - 3
: Disable Lower  bit, 3: Disable
Lower 3 bit