Table of Contents
Advertisement
Technical Information
ELECTRICAL
Input Power Source:
Power Isolation:
Current:
Consumption:
Heat Equivalent:
Maximum Power Cable
Distance:
Radio-Frequency
Emission Standard:
VICONNET (IP)
Communication
System:
LAN Interface:
Number of Video
Channels:
Video Formats
Supported:
Video Transmission
Number of
Simultaneous Video
Streams:
Video Quality:
Alarms:
Video Bandwidth:
Hard Drive
Consumption Rate:
VN-856V5
Days Recording
Note: This table is based on the following conditions:
- 24 hours normal activity with 50% detected movement over time, Normal compression and Quality Q5 (320 x 240 pixels NTSC, 384 x 288 pixels PAL)
- Recording durations may vary b ased on actual scene activity.
24 VAC, ±15% or PoE (802.3af
compatible).
Input
Internal fully isolated power
input.
VN-856: 360 mA max.
VN-856DN: 410 mA max.
VN-856WDR: 380 mA max.
250 mA @48 VDC (PoE)
Power
VN-856: 5.8 W max.
VN-856DN: 6.5 W max.
VN-856WDR: 6.4 W max.
0.3 btu/min (0.09 kg-cal/min)
nominal.
Note: These figures represent
the conversion of 100% of the
electrical energy to heat. Actual
percentage of heat generated
will be less and will vary from
product to product. These
figures are provided as an aid in
determining the extent of cooling
required for an installation.
Refer to Table 1 (based on
24 VAC, standard camera).
FCC Class A/CE.
ViconNet Digital Video
Management System Version 5.
10/100 Mbps, TCP/IP Unicast.
1, over LAN connection.
NTSC and PAL, model
dependant.
Rate:
30 fps (25 fps, PAL).
Maximum 10 viewing/recording
streams per camera.
ViconNet software quality 1-8,
selectable on a 4-position bar
with 2 compression level settings
in resolutions 720 x 488 (863 x
586 PAL), 720 x 244 (863 x 293,
PAL), 360 x 244 (432 x 293,
PAL), 360 x 122 (432 x 146,
PAL).
Audio:
1 line-level microphone input;
0 dbm, 32 KHz bandwidth, 600
ohm impedance, 2 V RMS
(1 V p-p) output.
1 alarm in, 1 alarm out.
Alarm out: logic out; 3.2 V,
0.5 mA sink (max),
30 uA source (max).
1.7 Mbps (per video stream),
nom.
Refer to Table 2.
60
200
300
24
80
120
25
SOFTWARE OPERATION
Network Setup:
Site Authorization:
Macro Create & Edit:
Alarm Setup:
Authentication:
Picture Quality and FPS
VIDEO CHARACTERISTICS
Image Device:
Picture Elements:
Sensitivity:
Resolution:
Electronic Iris:
Scanning System:
Compensation/Wide
Dynamic Range:
Table 2
Hard Drive
Consumption
Remote Hard Drive Storage (GB)
500
600
900
200
240
360
XX181-10-02 Rev 110 VN-856V5 IP Camera
Standard network protocol type
using IP addressing scheme and
separate PC application
software.
Camera can be setup using
remote recorder or workstation
GUI. Permissions can be
assigned for macro create &
edit, alarm setup, Authentication,
Reports and System Status.
Supports up to 20 Groups and
100 Users.
System macros can be
configured to use the camera's
video. In addition, within macros,
alarms can be sent and remote
macros run.
An alarm can be triggered on
video motion detection and loss.
The alarm can be sent to remote
units.
The video from the camera can
be set to view the Authentication
status symbol on the displayed
video.
Camera video can be setup to
Priority:
prioritize recorded picture quality
and video FPS. Priority can be
assigned to user/macro
recording for highest requested
video quality or Master user
control.
1/3-inch interline transfer CCD.
Active
NTSC: 768 (H) x 494 (V).
PAL: 752 (H) x 582 (V).
VN-856
0.03 fc (0.3 lux) color/BW mode.
VN-856DN/VN-856WDR
0.03 fc (0.3 lux) color mode;
0.004 fc (0.04 lux) BW mode
VN-856/VN-856DN
0.0002 fc (0.002 lux) at x128
SENS-UP.
VN-856WDR
0.0001 fc (0.001 lux) at x256
SENS-UP
Conditions: lens at f/1.2, 50 IRE
AGC High, DNR High.
Horizontal
540 lines
NTSC: 1/60-1/100,000.
PAL: 1/50-1/100,000.
NTSC standard: 2:1 interlace,
525 lines, 30 frames/sec.
PAL standard: 2:1 interlace,
625 lines, 25 frames/sec.
Backlight
ON/OFF select.
1000
2000
400
800
3000
1200
Advertisement
Table of Contents
