1. Manuals
  2. Brands
  3. DTS Manuals
  4. Garage Door Opener
  5. NicKWash 600
  6. Installation manual

DTS 600 Installation Manual

Sectional
Hide thumbs Also See for 600:
Table of Contents

Advertisement

Quick Links

See also: User Manual
DTS 600/800
SECTIONAL DOOR OPERATOR
INSTALLATION MANUAL
Comply to: SANS IEC 60-335-2-103
DTS SECURITY
P.O.BOX 3399
EDENVALE
TELEPHONE 086 1000 387
Base plate-mounting instructions
Spartan +2711 392 5540 (H/O)
Pretoria +2712 361 5528
Alberton +2711 907 8846
Natal
www.dtssecurity.co.za
E-EEEE
NRCS Cert. no. 88934/002
1610
+2731 916 4002
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 600 and is the answer not in the manual?

Questions and answers

Maurice
March 31, 2025

How to tension guide cables

0

Related Manuals for DTS 600

Summary of Contents for DTS 600

  • Page 1 DTS 600/800 SECTIONAL DOOR OPERATOR INSTALLATION MANUAL Comply to: SANS IEC 60-335-2-103 NRCS Cert. no. 88934/002 DTS SECURITY P.O.BOX 3399 EDENVALE 1610 TELEPHONE 086 1000 387 Base plate-mounting instructions Spartan +2711 392 5540 (H/O) Pretoria +2712 361 5528 Alberton +2711 907 8846...

  • Page 2: Table Of Contents

    DTS 600/800 Garage Door Opener. DTS Security Products hereby further disclaims and rejects to the maximum extent permitted by law any liability or responsibility whatsoever for any direct,...

  • Page 3: Contents

    Contents Important Safety Warnings The DTS600/800 garage door opener described in this Unqualified personnel or those who do not know the manual is designed for the automation of residential occupational health and safety standards applicable to sectional overhead doors and one piece overhead tilting automatic gates and doors category must under no doors.

  • Page 4: Operating Controls

    Operating Controls. 1 SET Button (K1) - Confirm set and Reversing sensitivity. 2 CODE Button (K2) - Transmitter code set. 3 UP Button (K3) - Limit mode set. 4 DOWN Button (K4) - Limit mode set Circuit Board Connections. 5 Coupling for connecting the backup battery. 6 Coupling for connecting the motor.

  • Page 5: Installation Instructions

    Installation 1) Read the instructions carefully. 2) Make sure the door structure is solid and suitable to be motor driven. 3) Make sure that when the door is moving there are no friction points. 4) The door must be properly balanced and must be easily lowered and raised by hand. 5) Install a 220V, adequately protected 3 pin socket near where the DTS600/800 opener is going to be installed.
  • Page 6 Installation. Please ignore middle bracket on extrution. Position the bracket (E) on the studs (D) and secure them in place using 6 mm wing nuts. Fix the DTS600/800 opener to the doorframe or to the ceiling with the correct fixing (Fig. 5) maintaining a min. gap of 30 mm from the panel’s maximum height (Fig.
  • Page 7 Installation Remember there are specific standards that have to be strictly followed regarding the safety of electrical installations and automatic gates and doors. As well as the legal requirements and standards that must be adhered to, please take note of the following points to ensure maximum safety and reliability of your installation.

  • Page 8: Description Of The Connections

    Only qualified, trained personnel may carry out the installation and subsequent maintenance. Whoever installs and uses the DTS600/800 door opener will be held responsible for any damage caused. NOTE: Contact DTS Security Products technical department for the wiring diagram for the above connections if uncertain of the correct procedures.

  • Page 9: Setting Of Open And Close Positions

    Setting Open and Close Positions. Warning: Keep all persons and property clear of the garage door during the programming process. 5.1) Press and hold SET (K1) until the LED displays the letter 1. It turns into opening learn state. 5.2) Now press and hold UP (K3), the door must travel to the open position, release the button when the door has reached the desired open position.

  • Page 10: To Learn In Transmitters

    7.3.4) The GDO will allow one opening and closing. After closing, allow 2 seconds for lock out to activate. Note: When the GDO is in lock out mode, the DTS 60TX4 is the only transmitter that can be used to open the GDO. First press the button with the lock printed on the button followed by, within 2 seconds, the button that is programmed into the receiver.

  • Page 11: Typical Application

    Typical Application. The DTS600/800 (max. 2500mm travel) model can automate sectional and tilting overhead garage doors up to a height of 2600mm. Manual Disengagement. The DTS600/800 is equipped with a manual release cord to disengage the shuttle and move the door by hand while holding the handle down (Fig.

  • Page 12: Warranty

    • All goods are warranted to be free from faulty components and manufacture. • Faulty goods will be repaired or replaced at the sole discretion of DTS Security Products, free of charge. • This warranty is subject to the goods being returned to the premises of DTS Security Products.

This manual is also suitable for:

800

Table of Contents

Save PDF