Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Compass Atom 500
Summary of Contents for Compass Atom 500
-
Page 2: Ama Information
Thank you for choosing the Atom500 and welcome to Compass Model. The Atom500 has been designed to offer outstanding performance. Simplicity is the beauty. That is the message Compass try to pass to the customer with Atom500. Same as other compass products, Atom is powerful, stable, agile as well as accurate. -
Page 3: Warranty Procedures
If service is required, send the component in question (if not missing) together with a photocopy of your bill of sale and an accurate description of the problem and part. Ship components fully insured and prepaid. Compass Model is not responsible for any shipping damages. We will, at our discretion notify you of any costs involved you are required to pay all postage, shipping and insurance charges. -
Page 4: Necessary Items
Necessary items 6 channel or up radio and receiver. 3 mini servos. 1 gyro with rudder servo. 6S li-po battery 2100mah~3300mah. or 2 pack 3s li-po battery with same capacity. 。3 ，1 。6 ~ 3 3 0 0 Mini Servos 2100 。... - Page 5 Symbols & assembling & Mishandling due to failure to follow these instructions may result in damage, personal injury or danger. Blue Threadlock should be applied. Greace Use AB Glue Bearing Retainer * Always apply blue Threadlock when fixing Bolts on Metal parts. * Always apply green retainer where bearings has to be fit into metal parts.
-
Page 6: Landing Gear
Landing Gear / M3 x10 Self-Tapping 3 1 0 Se lfTapin g Bol t Bolt X 4 Str uts M3x5 Set Screw X 4 M 3x5 S et Sc rew Use AB Glue S kid C ap Skid Tail / Crimping belt damages the tensile cords and will result in M3 Washer x2 premature failure. - Page 7 Main Gear / Note : The mast collar is installed underneath the upper bearing block. Main Shaft M2.5 Nylon Lock Nut MastCo llar M2.5x10 Cap Head Bolt M2.5x18 Cap Head Bolt 2.5 1 0 Cap Head B o l t Use Threadlock Make sure mast collar is tightened securely onto the mast.
- Page 8 Rotor,Washout & Swashplate/ M3x3 Set Scr ew Paddle Inser t M2.5 x8 Self-Tapping Bolt X 4 M3x3 Set Screw x2 M2.5 Nut x1 2.5 1 6 Cap Head Bolt 2 .5 Paddle M2.5x16 Cap Head Bolt x1 Washout Link Ball without Wa sher Use Threadlock (Standard Versi on) P a d dl e Inser t...
-
Page 9: Equipment Illustration
Equipment illustration / Ailero n Pi tch E levat o r Rud d e r B rushles s Mot or Recei ver E sc ES C Linkage/ The following linkage lengths indications are basic values which could vary depend on used servos. Some fine adjustments are still needed in following setup steps. - Page 10 S er v o Sc r e w S e r v o A r m s 2 m m x 6 C a p H e a d B o l t S t a i n l e s s B a l l s F o r S p o r t F l i g h t F o r 3 D U s e If you find the Balllinks are too tight...
- Page 11 On Atom 5 00 , p it ch ra ng e c an be se t as S w a s h T y pe Se tting much as 2 6d eg . I f p it ch is se t t oo hig h , flight tim e w il l b e s ho rt er.
- Page 12 B) Adjust the link from the servo arms to the swash plate to level the swash plate. 。 Use a compass swash Plate Tool as guide. 。 c) Set Washout Arms level. 。 H o r i z o n t a l...
- Page 13 Servo Direction Check/ Turn on t he ra dio, po sit ion the he l i t ail p o i n t t o y o u r s e l f . M a k e s u r e r a d i o is set to 12 0 degree ccp m mo de.
-
Page 14: Rotor Direction
Canopy / Canopy M2.5x6 Self-Tapping Bolt X 2 Use AB Glue Drill a D mm Ho le he re Canopy Insert 2 .5 6 Self Tap Bolt Pu t t he ca nopy o n the body an d mark th e right the position of t h e c an opy in sert . -
Page 15: Pre-Flight Check
Washer Here No washer 9 teeth 8 teeth Copyright Compass Model 2008 As we continue to improve our products, this manual may not reflect all recent product amendments. For more information, please refer to : www.compassmodel.com www.compassmodel.com...
Need help?
Do you have a question about the Atom 500 and is the answer not in the manual?
Questions and answers