Filling The Salt Container; Rinse Aid Dispenser; Adjusting Salt Consumption - SCAN domestic SFO 2201 User Manual

Filling the salt container

Always use salt intended for use with dishwasher. The salt con-
tainer is located beneath the basket and should be filled as fol-
lows :
Attention!
• Only use salt specifically designed for use in dishwashers
! All other types of salt not specifically designed for use in
a dishwasher, especially table salt, will damage the water
softener. in case of dam ages caused by the use of unsuit-
able salt the manufacturer does not give any warranty nor is
liable for any caused damages .
• Only fill with salt just before starting one of the complete
washing program mes . This will prevent any grains of salt
or salty water, w hich may have been split, remaining of the
bottom of the m achine for any period of time, which may
cause corrosion.
A Remove the basket and then unscrew and remove the cap
from the salt container.
B Before first wash, add 1lt. of water in the salt container of
your machine.
C Place the end of the funnel (supplied) into the hole and
introduce about 1kg of salt. It is normal for a small amount
of water to come out of the salt container.
D After filling the container , screw the cap tightly back clock-
wise.
E Usually, the salt warning light will be cease to be illuminated
within 2-6 days after the salt container has been filled with
salt.
F Immediately after filling the salt into the salt container, a
washing programme should be started. Otherwise filter
system, pump or other important parts of the machine may
be damaged by salty water. It is out of warranty.
Important
1 The salt container must only be refilled when the salt warn-
ing light in the control panel comes on.
Depending on how fully the salt dissolves, the salt warning
light may still be on even though the salt container is filled.
If there is no salt warning light in the control panel (For
some Models),you can judge when to load the salt into the
softener by the cycles that the dishwasher had run.
2 If there are spills of the salt, a soak or a rapid program
should be run to remove the excess salt.

Adjusting Salt Consumption

1 Close the door, within 60 seconds after power on, press
"Start/Reset" button and hold for 5 seconds, the machine
will enter setting mode.
2 Press the "Start/Reset" button to select the proper set
according to your local environment, the sets will change in
the following sequence: H1->H2->H3->H4->H5->H6;
3 Exit the status of salt adjustment
There are 6 levels of salt consumption in all.It is recommended to
select the level according to below table:
Hardness level water softener
°dH mmol/l
1) 2)
0-5 0 - 0,9 1
6-11 1,0 - 2,0 2
12-17 2,1 - 3,0 3
18-22 3,1 - 4,0 4*
23-34 4,1 - 6,1 5
35-45 6,2 - 8,0 6
Note:
1) German degree of measurement for the water hardness
2) millimol, internationel unit for water hardness
*) factory setting
Contact your local water board for information on the hardness
of your water supply.

Rinse Aid Dispenser

The rinse aid is released during the final rinse to prevent water
from forming droplets on your dishes. That can leave spots and
streaks. It also improves drying by allowing water to sheet off
the dishes. Your dishwasher is designed to use liquid rinse aids.
The rinse aid dispenser is located inside the door next to the
detergent dispenser. To fill the dispenser, open the cap and pour
the rinse aid into the dispenser until the level indicator turns
completely black.
The volume of the rinse aid container is about 110ml.
20
Display
H1: RAPID
H2: 1 hour
H3: 1 hour & RAPID
H4: 90 min
H5: 90 min & RAPID
H6: 90 min & 1 hour