Page 2
Thank you for buying an innovative product from Fujitsu. Latest information about our products, useful tips, updates etc. is available on our website: "http://www.fujitsu.com/fts/" You can find driver updates at: "http://support.ts.fujitsu.com/download" Should you have any technical questions, please contact: •...
Page 5
FUJITSU Workstation CELSIUS M740 CELSIUS M740power Operating Manual Your CELSIUS... Ports and operating elements Important notes Getting started Operation Troubleshooting and tips System expansions Technical data Index...
Page 6
Trademarks Fujitsu, the Fujitsu logo and CELSIUS are registered trademarks of Fujitsu Limited or its subsidiaries in the United States of America and other countries. PS/2 is a registered trademark of International Business Machines, Inc.
DVD. If necessary, you can also print out the manuals. Validity of the Reference Manual This Reference Manual is valid for the following system: • FUJITSU Workstation CELSIUS M740 • FUJITSU Workstation CELSIUS M740power Fujitsu...
"Safety information" • cross-references to an external source, e.g. a web address: For more information, go to "http://www.fujitsu.com/fts" • Names of CDs, DVDs and titles or designations for other materials, e.g.: "CD/DVD Drivers & Utilities" or "Safety/Regulations" manual indicates a key on the keyboard, e.g:...
2 = Module bays for 3 " drives 6 = USB ports (2 x USB 3.0, 2 x USB 2.0) 3 = ON/OFF switch 7 = Hard disk front panel (removable) 4 = Headphone port 8 = Casing lock (optional) Fujitsu...
Ports and operating elements Rear 1 = Holes for padlock / lead seal and 3 = Ports for external devices device for Security Lock (device-dependent) 2 = Alternating voltage socket (AC IN) 4 = Slot covers Fujitsu...
If the device is brought from a cold environment into the room where it will be used, condensation may occur. To avoid damaging the device, wait until it has reached room temperature and is absolutely dry before initial startup. Fujitsu...
User DocumentationDVD You can find information on these subjects on the "Drivers & Utilities" DVD or on our website ("http://www.fujitsu.com/fts/about/fts/environment-care/"). For China: The energy efficiency of this product has been tested in accordance with GB 28380. The corresponding energy efficiency label can be used.
CE nnnn (!) ; nnnn: For digits and exclamation mark (!), see label on the product. You can find more information and declarations of conformity on the Internet at: "http://globalsp.ts.fujitsu.com/sites/certificates". This equipment can be used in the following countries: Belgium...
• Consult the dealer or an experienced radio/T.V. technician for help. Fujitsu Technology Solutions GmbH is not responsible for any radio television interference caused by unauthorized modifications of this equipment or the substitution or attachment of connecting cables and equipment other than those specified by Fujitsu Technology Solutions GmbH.
Fujitsu is not responsible for any radio or television interference caused by unauthorized modifications of this equipment or the substitution or attachment of connecting cables and equipment other than those specified by Fujitsu. The correction of interferences caused by such unauthorized modification, substitution or attachment will be the responsibility of the user.
Drives and boards If you have received drives or boards with your device, please do not install them until after first-time setup. How to install drives and boards is described in the "System expansions", Page 31 chapter. Fujitsu...
"Technical data", Page section "Ambient conditions"). Protect the device against dust, humidity and heat. Connecting the machine to the mains Mainsadapter, ► Connect the mains cable to the machine (1). ► Plug the mains plug into a three-pin socket (2). Fujitsu...
USB 2.0 - Universal Serial Bus, LAN port black LANport USB 3.0 - Universal Serial Bus, blue UniversalSerialBus Some of the connected devices require special software (e.g. drivers) (refer to the documentation for the connected device and operating system). Fujitsu...
Use only high-quality signal lines to connect the monitors. For the DVI interface, we strongly recommend DVI monitor cable S26361-F2391-L400. ► Follow the instructions contained in the monitor manual to prepare the monitor for operation (e.g. connecting cables). ► Plug the data cable into a suitable monitor port of the device. Fujitsu...
If the device requires separate software, please follow the instructions in the manufacturer’s manual. To ensure the transmission capacity of USB 2.0, the cable from the external USB device to the USB port of your device must not be longer than 3 m. Fujitsu...
► Switch on the monitor (see operating instructions for the monitor). ► Press the on/off button on the front of the machine. The operational display will light up and the machine will start. Fujitsu...
Help in your operating system. You will find more information on the system, as well as drivers, utilities and updates on the "Drivers & Utilities" DVD and on the Internet at "http://www.fujitsu.com/fts/support". You can find information and help on the Windows operating system functions on the Internet at "http://windows.microsoft.com".
The ON/OFF switch does not disconnect the device from the mains voltage. To completely disconnect the mains voltage, remove the power plug from the power socket. ► If necessary, switch the monitor off (see the operating manual for the monitor). Fujitsu...
• The indicator is not illuminated: The device is switched off (disconnected from the mains) or is ready to operate. If the device is ready to operate, it can be switched on with the ON/OFF switch. Fujitsu...
With some keyboards the ON/OFF switch can only be used with an ACPI (Advanced Configuration and Power Management Interface). Otherwise the key is inoperative. The mainboard must support this function. Keys, Keys, Keys, Enter key confirms the highlighted selection. The Enter key is also referred to as the "Return" key. Fujitsu...
In BIOS Setup, you can set the system functions and the hardware configuration of the device. When the PC is delivered, the default entries are valid (see "BIOS Setup" manual or manual for the mainboard). You can customise these settings to your requirements in the BIOS Setup. Fujitsu...
Security Lock. Lead-sealing To prevent unauthorised persons from opening it, the casing can be lead-sealed. To do this, feed the sealing chain through the holes (1) and seal the chain with the lead seal. Fujitsu...
Key turned towards the closed lock: The device is locked. • Key turned towards the open lock: The device is unlocked. Locking the casing ► Turn the key towards the closed lock Unlocking the casing ► Turn the key towards the open lock Fujitsu...
Operation of this module is not permitted in Taiwan. ► Connect the external SmartCard reader to your system as described in the instructions for the SmartCard reader. SmartCard reader, After the device is switched on, you will be prompted to insert your SmartCard. Fujitsu...
► For further clarification of the problem, contact the Service Desk for your country (see the Service Desk list or visit the Internet at "http://support.ts.fujitsu.com/contact/servicedesk"). When you do this, please have ready the identity number and serial number of your system.
► Restart the system. Incorrect setting for the monitor ► Press while the system is booting. ► Start the system in Safe Mode. ► Set up the monitor as described in the documentation for your operating system and monitor. Fujitsu...
You will find the instructions for restoring the contents of the hard disk in the "Recovery Guide" manual. Tips Topic Lack of system resources ► Close unnecessary applications. ► Run the applications in a different order. Other manuals Further manuals are provided as PDF files on the "Drivers & Utilities" DVD. Fujitsu...
An update of the BIOS may be required for a system expansion or hardware upgrade. Further information can be found in the BIOS help section or if necessary in the Technical Manual for the mainboard. Fujitsu...
The equipment and tools you use must be free of static charges. • Only touch or hold the boards by the edge or, if present, at the areas marked green (Touch Points). • Never touch pins or conductors on boards fitted with ESDs. Fujitsu...
► On devices with a casing lock: Unlock the casing. ► Lay the device on its side in the manner shown. ► Pull the locking device (1) and swivel the side part in the direction of the arrow (2). Fujitsu...
• Optional installation kit: maximum of eight 2 inch drives "Accessible drives" are e.g. DVD or CD ROM drives, into which a data medium can be inserted from outside. "Non-accessible drives" are for example hard disk drives. Fujitsu...
Do not dispose of the cover of the Ultra Slim drive bay. For cooling and protection against fire you must refit the cover if you remove the drive again later (see "Removing an accessible drive", Page 41). ► Remove the cover of the Ultra Slim drive bay. Fujitsu...
Page 40
► Secure the drive carrier with the screws (2). ► Connect the cables to the drive. Make sure the polarity is correct. ► Close the casing (see "Closing the casing", Page 34). It may be necessary to modify the entry for the drive in the BIOS Setup. Fujitsu...
► Push the drive carrier a few centimetres out of the casing in the direction of the arrow (2). ► Pull the drive carrier completely out of the casing in the direction of the arrow (3). ► Remove the screws (1). ► Pull the drive out of the drive carrier (2). Fujitsu...
Page 42
► Close the casing (see "Closing the casing", Page 34). It may be necessary to modify the entry for the drive in the BIOS Setup. Fujitsu...
► Push the drive metal plate upwards (2) so it is released from the catches with which it is secured. ► Lift the drive cover away from the casing (3). ► Connect the drive cover to the drive (1). Fujitsu...
(1). ► Connect the cables to the drive. Make sure the polarity is correct. ► Close the casing (see "Closing the casing", Page 34). It may be necessary to modify the entry for the drive in the BIOS Setup. Fujitsu...
► Push the drive a few centimetres out of the casing in the direction of the arrow (2). ► Pull the drive completely out of the casing in the direction of the arrow (3). ► Remove the drive cover from the drive (1). Fujitsu...
If you have ordered a device with a SmartCard or MultiCard reader, the module holder, SmartCard or MultiCard reader are already built in on delivery. If you have ordered a device without a SmartCard or MultiCard reader, a blind cover is installed instead of the module holder. Fujitsu...
Screwing the reader onto the module holder ► With the component side facing downwards, slide the reader in the direction of arrow (1) into the guide on the module holder (a). ► Fasten the reader with the screws (2). Fujitsu...
(1). ► Secure the module holder with the screws (2). ► Connect the cables to the boards and the mainboard. Make sure the polarity is correct. ► Close the casing (see "Closing the casing", Page 34). Fujitsu...
"Installing a module holder with reader", Page 44). ► Remove the reader from the module holder (see "Removing the reader from the module holder", Page 46) and install a blind cover in the drive bay. ► Close the casing (see "Closing the casing", Page 34). Fujitsu...
• four 2 inch drives • or: two 2 inch drives and two 3 inch drives • or: four 3 " drives Standard assembly kit C78 for up to 4 drives: Fujitsu...
Page 51
first remove the hard disk fan and the card holder. Removal of the hard disk fan, the card holder and the installation of the installation set are described in the following chapters. Fujitsu...
Page 54
► Press the locking lugs on the connectors at the old slot inwards and disengage them. ► Remove the connectors from the old slot. ► Replace the connector at the new slot in the correct position. ► To ensure that the connectors engage correctly, always also push the locking lugs outwards. Fujitsu...
If you wish to use an installation kit for your hard disks which is other than that which was installed in your device in the factory, proceed as follows: Only the relevant components are shown in the following illustrations for reasons of simplification. Fujitsu...
Page 56
Press the catch to unlock it and press the cable retainer backwards out of the opening. ► Undo the screws (1) on the old installation kit. ► Slide the old installation kit in direction of the arrow (2). ► Take the old installation kit out of the casing (3). Fujitsu...
Page 57
4 drives) at the respective slot, in the correct position. ► To ensure that the connectors engage correctly, always also push the locking lugs outwards. ► Reinstall the hard disk fan (see "Install the hard disk fan", Page 69). Fujitsu...
Removing the hard disk front panel ► Press the unlocking keys on the sides of the hard disk front panel (1). ► Fold the hard disk front panel in the direction of the arrow (2) and remove it from the casing. Fujitsu...
Page 59
System expansions Removing the protective grille ► Pull the protective grille away from the casing (1). Fujitsu...
EasyChange rail in the corresponding holes on the hard disk. By default, the wiring for standard installation (max. four 2 -inch drives) is installed. If you wish to install other or different drives, use the supplied cables. Fujitsu...
Removing the hard disk drive ► Open the casing (see "Opening the casing", Page 33). ► Remove the hard disk front panel (see "Removing the hard disk front panel", Page 54). ► Remove the protective grille (see "Removing the protective grille", Page 55). Fujitsu...
Page 62
► Pull the EasyChange rails off the hard disk drive. ► If you no longer need the EasyChange rails, secure them again at their location in the drive cage. It may be necessary to modify the entry for the drive in the BIOS Setup. Fujitsu...
Page 63
"Securing the hard disk front panel", Page 59). Securing the hard disk front panel ► Place the hard disk front panel in the guide openings as illustrated. ► Fold the hard disk front panel in the direction of arrow (1) until you feel it engage. Fujitsu...
Push the locking lug on the upper, removable part of the card holder in the direction of the arrow (1). Lift the card holder away from the fan (2). Fujitsu...
Page 65
► Swivel the retaining clamp back again until you feel it click into place (2). ► Connect the cables to the board. ► For display adapters with additional power supply: Attach the display adapter power cable to the power supply. Fujitsu...
Page 66
► Close the casing (see "Closing the casing", Page 34). If you have installed or removed a board, please check the relevant slot settings in the BIOS Setup. If necessary, change the settings. Further information is provided in the board documentation. Fujitsu...
► Push the mounting clip (1) towards the slot cover to unlock it, then move it towards the back panel of the device. ► Pull the board out of the slot in the direction of the arrow (2). ► Place the board in suitable packaging. Fujitsu...
Page 68
For cooling, protection against fire, and in order to comply with EMC (electromagnetic compatibility) regulations, you must refit the slot cover. ► Slide the slot cover into the slot (1). ► Press on the retaining clip until it you feel it engage (2). Fujitsu...
Page 69
"Closing the casing", Page 34). If you have installed or removed a PCI board, please check the relevant PCI slot settings in the BIOS Setup. If necessary, change the settings. Further information is provided in the PCI board documentation. Fujitsu...
This enables the use of a GFX card with 6 and/or 8-pin connectors. If you require other cables, you can purchase these from Fujitsu. The power supply (PSU) installed in the system can supply a continuous 18.5 A for display adapters via any power supply.
► Disconnect the fan cable from the mainboard. ► Swivel the hood in the direction of the arrow (1) until the guide on the fan (a) fits through the grooves of the hood. ► Unhook the hood. ► Remove the hood from the casing. Fujitsu...
Page 72
System expansions ► Move the catches of the fan in the direction of the arrow (1) so that the fan releases from the location. ► Remove the fan from the casing (2). Fujitsu...
Page 73
► Connect the fan cable to the mainboard. ► Position the hood in the casing and slide the grooves of the hood into the guides on the fan (a). ► Carefully fold the hood down (1) until you feel it latch into place. Fujitsu...
33). ► Disconnect the fan cable from the mainboard. ► Press the catch of the fan in the direction of the arrow (1) so that the fan releases from the location. ► Remove the fan from the casing (2). Fujitsu...
► Remove the hood of the hard disk fan and the hard disk fan itself (see "Remove the hard disk fan", Page 67). ► Undo the screws on the heat sink. ► Lift the heat sink out of the casing. You can now replace the processor. Fujitsu...
► Tighten the screws. ► Reinstall the hard disk fan and the hood of the hard disk fan (see "Install the hard disk fan", Page 69). Never attach or detach fans during operation. This can cause problems controlling the mainboard fan. Fujitsu...
► Press the catch in the direction of the arrow (1). The battery jumps out of the holder slightly. ► Remove the battery (2). ► Push the new lithium battery of the identical type into the holder (3) and press it down until it engages. Fujitsu...
• Celsius M740power (1000 W PSU), 100 V – 240 V • Celsius M740 (600 W PSU), 100 V – 240 V Dimensions Width/depth/height: 186 mm x 481 mm x 430 mm / 7.32 inch x 18.93 inch x 16.92 inch Weight in basic configuration:...
19–20 Connecting a USB mouse 18 switching on for the first time 19 Contents of delivery 14 Ctrl+Alt+Del 24 Cursor keys 23 Kensington Lock 25 Keyboard 23 keyboard shortcuts 24 Data protection 25 Keyboard shortcuts 23 Device Connections 16 Fujitsu...
Page 80
BIOS Setup 24 Monitor, System unit, see Device 10 switching off 21 switching on 21 Transportation 9–10 Note safety 9 Notes Universal Serial Bus 16 CE marking 11 Upgrades, important 9 device 31 Numeric keypad 23 USB devices, connecting 18 Fujitsu...
Page 81
Index USB port 18 connecting keyboard 18 Workstation 15 USB port, connecting devices 18 User Documentation DVD 10 Fujitsu...