Olympia CDP24106 User Manual

Bluetooth telephone

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

CDP24106 USER GUIDE

CDP System does not include a V90 modem

CDP System does not support: Dial Up Networking (DUN); Personal Area Network Profile

(PAN); Cordless Telephony Profile (CTP); Object Exchange (OBEX)

The CDP is not user-upgradable

Pg. 12

What about security?

The Base is set to be discoverable by pressing and holding the page

Button for 10 seconds. The 'envelope' icon flashes and you'll hear a

Beep to confirm the base is discoverable.

Pg. 42

North American dialing feature is not supported

Pg. 45

Registration

10.

Pg. 52

Bluetooth functions – Device pairing

1. Press and hold the base page button for 10 seconds. The

'envelope' icon will blink to show the base station is discoverable.

Headset pairing

Pg. 55

Base station does not have a Flash feature

Errata Sheet

Press and hold down page on the base station until the

'envelope' icon flashes and you hear a beep.

After the 'envelope' icon flashes (not 'mute').......

On the CDP handset, select MENU → BS SETTINGS →

BLUETOOTH → ADD HEADSET.

Put the headset into pairable mode (see headset user guide).

On the CDP handset, select NEXT to enter the PIN screen.

Enter the headset PIN code; the base station will beep while

it is searching. A final high pitched beep will indicate success;

a low pitched beep indicates failure.

If the procedure completes successfully, the headset will

terminate the pairing mode. If pairing fails, check your

headset PIN code and pairing instructions, then try again.

Press the headset call control button to activate headset

coordination with the CDP base. You may have to power

cycle the headset, base, or both. Your headset will now

receive calls via the base station.

Table of Contents

Need help?

Do you have a question about the CDP24106 and is the answer not in the manual?

Questions and answers

Summary of Contents for Olympia CDP24106

Page 1 CDP24106 USER GUIDE Errata Sheet CDP System does not include a V90 modem CDP System does not support: Dial Up Networking (DUN); Personal Area Network Profile (PAN); Cordless Telephony Profile (CTP); Object Exchange (OBEX) The CDP is not user-upgradable Pg. 12...
Page 4: Welcome
Radio signals transmitted between the handset & base may cause interference to hearing aids. This product should not be used near emergency / intensive care medical equipment and should not be Thank you for purchasing the Olympia Cordless Data Phone (CDP). As you will have already realized, this used by people with pacemakers.
Page 5: Copyright
Printed in China. Trademark Information Olympia ® is a registered trademark of Olympia International Holdings Ltd. Bluetooth is a trademark owned by Bluetooth SIG, Inc. and is used by Mansella Limited and Giant Wireless Technology Limited under license. USER GUIDE Page 4 www.olympiaphones.com...
Page 6: Table Of Contents
Contents The phone · · · · · · · · · · · · · · · · · · · · · · · · · 14 Contents WELCOME The phone buttons · · · · · · · · · · · · · · · · · · · 14 Keypad ·...
Page 7 Contents Handset speaker on/off · · · · · · · · · · · · · · · · · 23 Handset name· · · · · · · · · · · · · · · · · · · · · · 30 Pulse/Tone ·...
Page 8 Software installation · · · · · · · · · · · · · · · · · · · 48 Olympia Data Phone Manager (DPM) · · · · · · · · · · · · 50 DPM setup·...
Page 9: Fcc Information
If this equipment Olympia CDP 2.4 causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn't practical, the telephone Reorient or relocate the receiving antenna.
Page 10: Start Up
Overview 4. Battery pack User guide in your user guide to acquaint yourself with advantages and benefits provided by your Olympia Cordless Data Phone 5. Power supply Software on CD-ROM (CDP and USB Adaptor) (CDP) on page 11. 6. Belt clip...
Page 11: Care Of Your System
Start up Care of your system Connecting the system Environmental When setting up the base station, please ensure you use the telephone line cords supplied with this unit, using any other telephone line cords could cause Do not expose the CDP to direct sunlight. a malfunction and invalidate the warranty.
Page 12: Overview
Overview Your system's functions Phone functions Overview Your phone is suitable for use as multi-extension home, home-based office or small business system. It Bluetooth™ digital technology enables two calls per handset; one on each external line or a combination of external call and intercom call.
Page 13: Bluetooth - A Technology Overview
"found" device. If you don't know the PIN, you cannot use that device. The Olympia CDP Bluetooth product family works with all kinds of Bluetooth devices - PCs, laptops, PDAs, headsets etc. This is achieved by implementing a range of relevant Bluetooth profiles: In the CDP additional handsets must be paired to the base before they can be used.
Page 14: What Can My Usb Adapter Do
Overview What can my USB adapter do? PC or laptop (with Bluetooth Adapter) Your Olympia Bluetooth adapter supports the following: - Dial up networking Connects to the Internet via a modem Bluetooth enabled Local area Networking Connects to other PCs locally...
Page 15: The Phone
System controls & indicators The phone The phone buttons System controls & indicators Keypad These keys enable you to enter telephone numbers and text when required. For text entry, see page 43. Clip-on cover When the keypad is referred to in 'How to' steps, they will be shown as pqrs wxyz Display...
Page 16: Phone Display
System controls & indicators Status icons Phone display One or more of the status icons will be displayed in the standby mode and will indicate the following: Call type: Line Battery charger indicator. The number of bars is proportional to the charge level. Charge the Call Details Connected Intercom...
Page 17: Function Icons
System controls & indicators Function icons Base station These icons identify the currently available function. The function title is also displayed next to the icon as shown in the example of the phonebook function below: key is used to scroll through the functions and the key is pressed to select them.
Page 18: Menu Maps
Menu maps Main menu map Phonebook menu map Menu maps The phonebook menu is accessed from the main menu or the in-call menu. The main menu is accessed from your handset when it is in the standby mode. Displays a list of the entries in the active phonebook (base or For the phonebook menu handset).
Page 19: System Menu Map
Menu maps System menu map In-call menu map The system menu is selected from the main menu and enables you to make an intercom call and change The in-call menu becomes available 6 seconds after a connection is made. the base station and handset settings as follows: The menu below contains the menu structure for a normal single call.
Page 20: Pre-Call Menu Map
Menu maps Pre-call menu map The pre-call menu is accessible for 6 seconds from when the line is selected. For the phonebook menu map, see opposite. Enables you to set the dialling mode (see page 24). Accesses service provider services. Adjusts earpiece volume (see page 23).
Page 21: Making Calls
Making calls Keypad - number first Handset call methods Making calls 1. Key in the phone number required. For pre-call and in-call menus, see page 26. pqrs wxyz 2. Use if necessary to delete incorrect digits as Your phone accommodate the North American 7, 8, 10 and 11 digit dialing they are entered.
Page 22: Redial List (Outgoing Calls)
Making calls Redial list (outgoing calls) Call log (incoming caller ID) 1. From the standby screen press , the call log 1. From the standby screen press , the redial option option will be displayed. will be displayed. 2. Press to display the call log list then use 2.
Page 23: Phonebook
Making calls Phonebook Dialing options menu Each handset can access its own phonebook or the shared phonebook stored in the base station as follows: The number edit screen has a menu attached to it that offers the ability to insert a pause into the 1.
Page 24: In-Call Menu
Making calls Mute on/off In-call menu During a call you can mute your phone so that you cannot be heard but you can still hear the other party. During a handset call, the in-call menu options become available. 1. When a call is connected, the mute on option is displayed. If it is not displayed, use to display it.
Page 25: Pulse/Tone
Making calls Pulse/Tone Intercom If your exchange requires your phone to use pulse Dialing but during a call your need to enter tones (e.g. for a call center, etc.), you can switch to tone Dialing temporarily as follows: The intercom function is available between handsets. 1.
Page 26: Handset To Handset
Making calls Handset to handset Keypad lock To make an intercom call from a handset to another handset, proceed as follows: To prevent accidental use of your handset, it has a keypad lock function. To lock or unlock your handset's If there is an active call in progress, inform the person connected on the keypad, proceed as follows: active call they are about to be put on hold.
Page 27: Controlling Two Calls
Making calls Set to tone/pulse Controlling two calls This option allows you to set the dial type. On a handset, the two-call control functions are available when two calls are active; one external and one intercom. 1. Within 6 seconds of selecting a line, press until the set to pulse option is displayed then press Switch call...
Page 28: Volume
Making calls Volume Redial This option enables you to set the earpiece volume. This option accesses the redial list. 1. Within 6 seconds of selecting a line, press until 1. Within 6 seconds of selecting a line, press until the volume option is displayed then press the redial option is displayed then press 2.
Page 29: Settings
Settings Handset set-up Handset audio settings Settings Handset ring type The handset set-up menu allows you to change the following handset functions: To set the handset ring type, proceed as follows: • • Audio Registration 1. Access the handset settings menu (see left) and use Handset ring type as necessary to highlight the audio option.
Page 30: Handset Ringer Volume
Settings Handset ringer volume Handset auto answer (pickup/headset) There are two auto answer options: pickup answer (where the handset will automatically connect to an Different ringer volumes can be set for line 1 or 2. The procedure for both is incoming call when it is lifted from its base) or headset answer (where a handset will automatically identical.
Page 31: Tone (Key Click, Out Of Range & Battery Warning)
Settings Tone (key click, out of range & battery warning) Handset name The phone's key click, out of range and battery warning can all be turned on Each handset can be given its own name to suggest its normal location (e.g. LOUNGE). or off.
Page 32: Registration Menu
Settings Registration menu Language Any one of four different languages can be selected for your phone's display, as follows: 1. Access the handset settings menu (see page 28) and use as necessary to highlight the registration option. 1. Access the handset settings menu (see page 28) and use as necessary to highlight the language option.
Page 33: Backlight
Settings Backlight Reset Your phone's backlight illuminates your handset's display and its keypad for approximately 10 seconds whenever To reset your handset to the factory settings, proceed as follows: a button is pressed or an incoming call is received. To turn this feature on or off, proceed as follows: 1.
Page 34: Base Station Set-Up
Settings Base station audio settings Base station set-up Base station ring type The base station set-up menu (accessed from the handset) allows you to change the following base 1. Access the base station settings menu (see opposite) and station functions: as necessary to highlight the audio option.
Page 35: Base Station Ringer Volume
Settings Base station ringer volume Bluetooth™ This option enables you to pair a Bluetooth™ headset to your base station. 1. Access the base station settings menu (see page 33) and as necessary to highlight the audio option. 1. Access the base station settings menu (see page 33) and use as necessary to highlight the 2.
Page 36: Base Station Name
Settings Base station name Boost mode Each base station can be given its own name (e.g. Base 1). Your phone has a boost feature designed to improve both the sound quality and operating range if you are experiencing interference. The actual range will depend on your environment. The Boost mode is 1.
Page 37: Set Base Passkey Pin
Settings Set base passkey PIN Pulse/Tone The base PIN is required to enable other Bluetooth™ equipment (including handsets, headsets and The CDP can either use DTMF (Tone) Dialing, or pulse dial. This allows the CDP to be compatible with Bluetooth™ enabled PC's etc.) to register or pair with the base station. To change the base PIN from the both new and older telephone exchanges.
Page 38: Home And Local Codes
Settings Home and local codes Reset base station Use the appropriate option to store either 1 home code or 5 local codes. This stored information is then used To reset your handset to the factory settings, proceed as follows: to display an incoming call number correctly. It will also mean the number is saved in the call log correctly. 1.
Page 39: Storing & Managing Numbers
Storing & managing numbers Editing stored phone numbers Phonebooks Storing & managing numbers 1. From the standby screen press , the list option Each handset can access its own internal phonebook or the phonebook stored in the base station as follows: will be displayed for the currently active phonebook (handset or base).
Page 40: Deleting A Stored Phone Number
Storing & managing numbers Deleting a stored phone number Deleting all stored phone numbers 1. From the standby screen press , the list option 1. From the standby screen press , the list option will be displayed for the currently active phonebook will be displayed for the currently active phonebook (handset or base).
Page 41: Copy A Phonebook Number
Storing & managing numbers Copy a phonebook number Redial list & call log You can copy a phone number in a handset's phonebook to the base station's phonebook or copy a phone number from the base station's phonebook to the handset you are using as follows: The redial list is specific to each handset and contains the last 20 numbers you have called from it whilst the call log is common to all handsets and contains the last 20 numbers that called you (answered and 1.
Page 42: Delete All Numbers
Storing & managing numbers Delete all numbers Copy a number to a phonebook You can copy a number from the redial list or call log to your handset or base station as follows: 1. From the standby screen, press until the redial or call log option is displayed then press 1.
Page 43: North American Dialing (7, 8, 10 &11 Digit Dialing Feature)
Storing & managing numbers North American dialing (7, 8, 10 &11 digit dialing feature) Your phone can store and dial North American 7, 8, 10 and 11 digit numbers using the call log functions. Whenever a dial or number edit screen is encountered during the use of these functions, you can use to scroll through the various formats.
Page 44: Text Handling
Text handling Text entry Text handling Your phone's keypad can be used for entering text. When prompted to enter or edit a name, subsequent presses of the keypad keys will produce the following characters: Digit Upper case mode Lower case mode Digit Upper case mode Lower case mode P Q R S 7...
Page 45: Battery Care
Battery care Battery type Battery warning Battery care When the battery is very low, your phone will sound a warning. This warning tone can be set on or off, Use only the following type and size of battery pack: GP70AAAH3BX see page 30 for setting procedures.
Page 46: Extra Handsets
Extra handsets Overview 6. Press to display the registration menu. Extra handsets Your phone system can have up to 4 handsets connected to the base station. To enable a handset to be 7. Press until the register option is highlighted. active, it must first be registered with the base station.
Page 47: Troubleshooting Troubleshooting Guide
Troubleshooting Troubleshooting guide Troubleshooting Symptom Solution General misbehavior Reset the unit by removing the power for 10 seconds, then re-applying. The CDP is designed to accept a degree of interference but as the unit is connected to both the mains electricity supply and the telephone system, the degree of interference is beyond our control. No dial tone.
Page 48 Troubleshooting Symptom Solution The handset does not charge Make sure that the handset is correctly seated in the charger. Make sure that the charger contacts are clean. Use only a clean, dry cloth or a standard pencil eraser. Do not use any solvent as this may damage the finish. The battery pack may be faulty or come to the end of its useful life –...
Page 49: Advanced System Use Advanced Facilities
Just after the DOS window is displayed, the Insert the CD-ROM supplied with your phone DataPhone installation welcome window into the computer's CD-ROM drive. The will be displayed (see right). Olympia welcome window will be displayed (see right). Click to continue with the Next installation.
Page 50 Advanced system use When you have started the installation When the Bluetooth™ welcome window is process, the DataPhone license window will displayed (see right), click Next be displayed (see right). proceed with the installation process. Click I accept the terms in the and then License Agreement to continue with the installation.
Page 51: Olympia Data Phone Manager (Dpm)
Advanced system use When the Device not found Olympia Data Phone Manager (DPM) window is displayed (see right), plug the Bluetooth™ adaptor into your computer's USB port and click Install the drivers from the CD-ROM before connecting the USB cable to the CDP.
Page 52: Dpm Setup
Advanced system use DPM setup 7. In DPM select to perform a refresh. File > Refresh If you are using your phone system as a Personal Area Network (PAN) the DPM requires no further setup. If you are not using your system as a PAN, 8.
Page 53: Bluetooth™ Functions
Advanced system use Headset pairing Bluetooth™ functions The procedure below details how to pair to a Bluetooth™ headset from the base station, to pair from the handset, see page 34. Discoverable Mode 4. Press and hold the store button on the base station until the second beep. Placing the base station in "discoverable"...
Page 54: Dial Up Networking
Advanced system use Dial up networking Network access After pairing your devices, connect to the Internet, using the Bluetooth™ software on your PC to discover the Bluetooth™ profiles your system provides (see page 55). Select "Dial-up Networking". This will open a screen that asks you for your internet username, password and ISP telephone connection number. For full details on setting up dial up networking, use the relevant 'movie' file on the CD ROM.
Page 55: Setting Up The Client Connection
Advanced system use In Desktop right-click on Setting up the client connection My Network , and select Places Properties Ensure that the client is Bluetooth-enabled, with the PAN profile available. If not, carry out the installation process detailed from page 48. Make the CDP discoverable and pair the two devices.
Page 56: Bluetooth™ Profiles
Advanced system use Bluetooth™ profiles Select Internet Protocol and click on (TCP/IP) Properties Currently your system supports: • Generic Access Profile (GAP) • Service Discovery Profile (SDP) • Dial-up Networking Gateway (DUN-GW) • Headset Audio Gateway Base station Using the base station, the flash option is available by pressing the flash button. On the Tab: General...
Page 57: Usb Adaptor System Requirements
USB Adaptor Your Desktop PC or Notebook PC should match the following requirements in order to run the software: Plug the Olympia Bluetooth USB Adaptor into the USB port, when prompted to on the screen. • Pentium II Class PC, CPU speed 200MHz or above Hardware: •...
Page 58 Warranty Warranty Warranty Statement / Olympia Phone Product This warranty covers any defect in material or workmanship for a period of one year from date of purchase. At our option we will repair or replace your unit. To enforce warranty, call Wave Customer Service at for a return authorization.

Olympia CDP24106 User Manual

Quick Links

Need help?

Questions and answers

Related Manuals for Olympia CDP24106

Summary of Contents for Olympia CDP24106

Table of Contents