Phone: (800) 553- -8033 or (763) 513- -2850 www.tennantco.com FaSK--PAK is US registered trademark of Tennant Company. Specifications and parts are subject to change without notice. Copyright E 2006, 2007, 2008 TENNANT COMPANY, Printed in U.S.A. All rights reserved. Tennant T5e (03- -08) Home...
Do not modify the machine from its original order to avoid a hazard. design. WARNING: Spinning Brush. Keep Hands Away. Turn Off Power Before Working On Machine. Tennant T5e (11- -08) Home Find... Go To..
Gas. Keep Sparks And Open Flame Away. Keep Battery Compartment Open When Charging. SPINNING BRUSH LABEL - - Located on scrub head WARNING: Spinning Brush. Keep Hands Away. Turn Off Power Before Working On Machine. Tennant T5e (10- -06) Home Find... Go To..
24. Pad Release Plunger 12. Rear Fill Port 25. Pad Driver Window 13. Recovery Tank Support Stand 26. Scrub Head Skirt 14. Circuit Breaker Panel 27. Parking Brake (option) 28. Cylindrical Brush Scrub Head Tennant T5e (09- -08) Home Find... Go To..
-H2O system on/off switch (ec- -H2O Model) 5. Control Console Height Adjustment Lever 10. ec- -H2O system indicator light (ec- -H2O Model) 6. Speed Control Knob 11. Main Power on/off Key Switch 12. Hour Meter Tennant T5e (09- -08) Home Find... Go To..
Four 6 volt, 235A/20h deep cycle batteries. Maximum battery dimensions: 190 mm W x 275 mm L x 284 mm H. 1. Park the machine on a level surface, remove the key and set the parking brake, if equipped. Tennant T5e (09- -08) Home Find... Go To..
Performs well on buildup, grease, or tire marks. Polishing Pad (White) - - Used to maintain highly polished or burnished floors. Buffing Pad (Red) - - Used for light duty scrubbing without removing floor finish. Tennant T5e (09- -08) Home Find... Go To..
(Figure 7). FIG. 9 4. To remove the pad driver, raise the scrub head and push the pad release plunger downward (Figure 10). 2 mm FIG. 7 FIG. 10 Tennant T5e (10- -06) Home Find... Go To..
FIG. 14 BRUSHES). 3. When the supply hose is not in use, connect the storage plug to prevent the FaST system from drying out and clogging up the hose. (Figure 15). FIG. 15 Tennant T5e (03- -08) Home Find... Go To..
H2O model: Press the ec- -H2O system switch to the on ( I ) position (Figure 19). FIG. 17 NOTE: The ec- -H2O system indicator light will not turn on until the machine starts scrubbing. Tennant T5e (09- -08) Home Find... Go To..
Page 13
(Figure 24). Do not operate brush pressure button (Figure 21). the machine in the red zone, floor damage or brush motor overload may result. FIG. 21 FIG. 24 Tennant T5e (09- -08) Home Find... Go To..
ATTENTION: (ec- H2O model) Do not allow solution tank to run dry. ec- H2O module failure may result if operated without water for an extended period. FIG. 26 FIG. 27 Tennant T5e (09- -08) Home Find... Go To..
The hour meter records the number of total hours the brush motors have been powered on. Use the hour meter to determine when to perform recommended maintenance procedures and to record service history (Figure 30). See MACHINE MAINTENANCE. FIG. 30 Tennant T5e (09- -08) Home Find... Go To..
3. Remove the recovery tank cover and rinse out the tank (Figure 38). FIG. 41 FIG. 38 4. Clean the float shut-off screen located inside the recovery tank (Figure 39). FIG. 39 Tennant T5e (10- -06) Home Find... Go To..
Acd = Set for wet/lead acid batteries FIG. 44 5. Connect the charger’s AC power supply cord into a properly grounded receptacle (Figure 45). NOTE: The machine will not operate when charging. FIG. 42 Tennant T5e (10- -06) Home Find... Go To..
E03 reappears check battery or re- sulfated or faulty battery. place it. Safety timer exceeded maximum charging Replace battery. time. Interrupts charging cycle. Possible internal short circuit. Contact Service Center. Tennant T5e (10- -06) Home Find... Go To..
ATTENTION: Do not disconnect the charger’s DC cord from the machine’s receptacle when the charger is operating. Arcing may result. If the charger must be interrupted during charging, disconnect the AC power supply cord first. FIG. 50 Tennant T5e (10- -06) Home Find... Go To..
6. Raise the scrub head and pull the machine away. 7. Observe the brush pattern on floor. If the brush pattern is uneven or tapered, adjustment is required. 8. Reconnect drive motor wire. Tennant T5e (10- -06) Home Find... Go To..
Retighten hex screw (Figure 57). FIG. 59 3. Remove the recovery tank float shut--off screen and clean (Figure 60). FIG. 57 5. Recheck brush pattern. NOTE: Replace brushes when bristles are worn to 15 FIG. 60 Tennant T5e (10- -06) Home Find... Go To..
Page 23
Cylindrical Brush Model FIG. 65 9. Wipe the squeegee blades clean (Figure 66). Store the squeegee assembly in the raised position to prevent blade damage. Cylindrical Brush Model FIG. 63 FIG. 66 Tennant T5e (10- -06) Home Find... Go To..
1. Remove the solution tank filter from underneath the machine and rinse out the screen (Figure 72). Make sure the solution tank is empty before removing filter. Cylindrical Brush Model Disk Model FIG. 69 FIG. 72 Tennant T5e (03- -08) Home Find... Go To..
FIG. 75 6. Clean the parking brake clamp with a cleaning solvent. FIG. 77 7. Check the machine for loose nuts and bolts. 8. Check the machine for leaks. Tennant T5e (10- -06) Home Find... Go To..
12/14 slotted edge for maximum water pickup. 6 Slots on one edge FIG. 81 MOTOR MAINTENANCE 12/14 Slots on Contact an Authorized Tennant Service Center for opposite edge carbon brush replacement. FIG. 78 Carbon Brush Replacement Hours Drive Transaxle Motor...
4. Turn the key to the on ( I ) position. FIG. 83 Replace the water and air filter. An 8mm hex wrench required to install new water filter (Figure 84). Water Filter (50 Mesh/Brown) Air Filter (50 Mesh/Brown) FIG. 84 Tennant T5e (11- -08) Home Find... Go To..
4. Open the recovery tank cover to promote air circulation. ATTENTION: Do not expose machine to rain, store indoors. 5. If storing machine in freezing temperatures, follow the FREEZE PROTECTION instructions below. Tennant T5e (09- -08) Home Find... Go To..
(Figure 90). When the antifreeze is visible, press the according to local waste disposal regulations. switch again to turn off the module. 5. The machine is now ready for scrubbing. FIG. 90 Tennant T5e (09- -08) Home Find... Go To..
FOR SAFETY: Avoid eye contact with antifreeze. RECOMMENDED STOCK ITEMS Wear safety glasses. Refer to the Parts List Manual for recommended stock items. Stock Items are clearly identified with a bullet preceding the parts description. See example below: Tennant T5e (09- -08) Home Find... Go To..
Discharged batteries Charge batteries Clogged solution valve Remove valve and clean Solution flow control knob set too low Adjust solution control flow knob Loose screw on control knob Calibrate knob and retighten screw. Tennant T5e (10- -06) Home Find... Go To..
Page 32
Drain solution tank. Remove solution tank filter, clean and reinstall Clogged detergent orifice/filter screen Replace orifice/filter screen (See FaST SYSTEM MAINTENANCE) Clogged FaST solution inlet filter Contact Service Center FaST Pump fuse blown Replace 7.5A fuse Tennant T5e (10- -06) Home Find... Go To..
Scrubbing 5% (3°), Transporting 8% (5°) * Run times are based on Continuous Scrubbing Run Times. ** Sound levels (ISO 11201) as recommended by the American Association of Cleaning Equipment Manufacturers (AACEM) and OSHA. Tennant T5e (10- -06) Home Find... Go To..
Cylindrical Cylindrical 1,357 mm 1,408 mm 1,471 mm 1,399 mm 1,399 mm 645 mm 737 mm 838 mm 711 mm 864 mm 908 mm 1,051 mm 1,185 mm 1,051 mm 1,185 mm Tennant T5e (09- -08) Home Find... Go To..