Maintenance; Protecting The Environment - Black & Decker KC360H Instruction Manual

Generally, a charging time of 4 hours will enable the tool to
operate at an effective power level for most tasks.
However, further charging for up to 8 hours could significantly
increase the run time, depending on the battery and charging
conditions.
Before using the tool, unplug the charger and disconnect
N
the tool from the charger.
Warning! Do not use the tool while it is connected to the
charger.
Warning! Do not charge the battery at ambient temperatures
below 4 °C or above 40 °C.
Selecting the direction of rotation (fig. C)
For tightening screws, use forward (clockwise) rotation.
For loosening screws use reverse (counterclockwise) rotation.
To select forward rotation, push the forward/reverse
N
slider (2) to the forward position.
To select reverse rotation, push the forward/reverse slider
N
(2) to the rearward position.
To lock the tool, set the forward/reverse slider into the
N
centre position.
Screwdriving (fig. C)
Select forward or reverse rotation using the forward/
N
reverse slider (2).
To switch the tool on, press the on/off switch switch (1).
N
To switch the tool off, release the on/off switch (1).
N
Spindle lock
This tool is fitted with an automatic spindle lock so that it can
be used as a normal screwdriver. Use the tool this way to
loosen very tight screws or to firmly tighten screws.
Hints for optimum use
Always use the correct type and size of screwdriver bit.
N
If screws are difficult to tighten, try applying a small
N
amount of washing liquid or soap as a lubricant.
Use the spindle lock to loosen very tight screws or to
N
firmly tighten screws.
Always hold the tool and screwdriver bit in a straight line
N
with the screw.
When screwing in wood, it is recommended to drill a pilot
N
hole with a depth equal to the length of the screw. A pilot
hole guides the screw and prevents splintering or
distortion of the wood. For the optimum size of the pilot
hole, refer to the table below.
When screwing in hardwood, also drill a clearance hole
N
with a depth equal to half the length of the screw. For the
optimum size of the clearance hole, refer to the table
below.
Screw size Pilot hole ø
(softwood)
No. 6 (3.5 mm) 2.0 mm
No. 8 (4 mm) 3.2 mm
No. 10 (5 mm) 3.5 mm
Accessories
The performance of your tool depends on the accessory used.
Black & Decker and Piranha accessories are engineered to
high quality standards and designed to enhance the performance
of your tool. By using these accessories you will get the very
best from your tool.
This tool uses screwdriver bits with a 1/4" (6.35) hexagonal
shank. Piranha Super-lok accessories are designed for use
with this tool.

Maintenance

Your Black & Decker tool has been designed to operate over a
long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger before
cleaning it.
Regularly clean the ventilation slots in your tool and
N
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth.
N
Do not use any abrasive or solvent-based cleaner.

Protecting the environment

Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Black & Decker product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials.
Pilot hole ø Clearance
(hardwood) hole
2.5 mm 4 mm
3.5 mm 5.0 mm
4.0 mm 5.7 mm
5