Advertisement
Quick Links
Compatibility
•
DVL GSR NB Insert
•
DVL GS (AU) Inbuilt
Packing List
•
DVL Ember‐Fyre Burner Assembly
•
6‐Piece Log Set
Burner Installation
1. Access the firebox.
2. Leave the air shield in place for NG (natural gas). Remove and discard the air shield for LP (propane).
NG
3. Install the burner. Install the side ember trays.
NOTE: Make sure the burner is fully seated over the orifices (the burner should be aligned all the way to
the right).
Page 1 of 6
DVL Ember-Fyre Burner
Installation Instructions
•
•
17601695.docx — 11/19/13
(SKU 96900107, 96900109)
Bag of Embers
Bag of Rock Wool
LP
© Travis Industries, Inc.
Advertisement
Related Manuals for Travis Industries DVL Ember-Fyre
Summary of Contents for Travis Industries DVL Ember-Fyre
-
Page 1: Installation Instructions
DVL Ember-Fyre Burner Installation Instructions (SKU 96900107, 96900109) Compatibility • DVL GSR NB Insert • DVL GS (AU) Inbuilt Packing List • • DVL Ember‐Fyre Burner Assembly Bag of Embers • • 6‐Piece Log Set Bag of Rock Wool Burner Installation 1. Access the firebox. 2. Leave the air shield in place for NG (natural gas). Remove and discard the air shield for LP (propane). -
Page 2: Log Set Installation
DVL Ember-Fyre Burner Installation Instructions (SKU 96900107, 96900109) Log Set Installation The logs are fragile, especially after being exposed to heat. • Make sure the gas control valve is “OFF” and the heater is cool prior to conducting service. •... -
Page 3: Left Log Placement
DVL Ember-Fyre Burner Installation Instructions (SKU 96900107, 96900109) Left Log Placement The left log has a hole on the bottom. Place the log so the pin on the burner inserts into the hole on the log (see photos below). Position the log so the right side straddles the burner holes. The log must not cover any burner holes. Right Log Placement The right log has a hole on the bottom. Place the log so both burner pins insert into the holes on the log (see photos below). Make sure the log is pushed back so it sits flat. Page 3 of 6 17601695.docx — 11/19/13 © Travis Industries, Inc. -
Page 4: Left Twig Placement
DVL Ember-Fyre Burner Installation Instructions (SKU 96900107, 96900109) Left Twig Placement The left twig has two holes in the bottom that fit over the pins on the back and left log (see photos below). Place the twig as shown below. Right Twig Placement The right twig has one hole in the bottom that fits over the pin on the back log (see photo below). The bottom of the log rests on the right log. Place the log as shown below. Page 4 of 6 17601695.docx — 11/19/13 © Travis Industries, Inc. -
Page 5: Front Ember Chunk Placement
DVL Ember-Fyre Burner Installation Instructions (SKU 96900107, 96900109) Front Ember Chunk Placement Place the ember chunk as shown in the photos below. Make sure the ember chunks does not cover any burner holes. Ember Placement A bag of embers is included with your burner kit to enhance the firebox. Place a layer of embers along the edges of the burner, on top of screw‐heads, and along the perimeter to enhance the aesthetics of the firebox. Do not place embers over any burner holes. See the photo below. Place a layer of embers along any visible edges of the burner. Page 5 of 6 17601695.docx — 11/19/13 © Travis Industries, Inc. -
Page 6: Rockwool Installation
DVL Ember-Fyre Burner Installation Instructions (SKU 96900107, 96900109) Rockwool Installation The included rock wool is placed on top of the burner to enhance the glow from the burner. The rock wool works best when it is applied in a very thin, porous layer. The best method for applying the rock wool is to brush it on to the burner. Compress a clump of rockwool between your thumb and forefinger. Use a stiff brush to apply a thin layer of rockwool fibers onto the burner. Do not use the entire bag of rockwool. Use only a small amount and save the remainder. Over‐use of rockwool will diminish the glow and may cause sooting or other adverse conditions. Page 6 of 6 17601695.docx — 11/19/13 © Travis Industries, Inc.