Self-Diagnosis Code Table - Sony DCR-HC1000 Service Manual

3.

SELF-DIAGNOSIS CODE TABLE

Self-diagnosis Code
Block Detailed
Function Code
C 0 4 0
C 2 1 0
C 2 2 0
C 3 1 1
C 3 1 1
C 3 1 2
C 3 1 2
C 3 1 2
C 3 1 2
C 3 1 2
C 3 1 3
C 3 1 4
C 3 1 4
C 3 2 1
C 3 2 1
C 3 2 2
C 3 2 2
C 3 2 2
C 3 2 2
C 3 2 2
C 3 2 3
C 3 2 4
C 3 2 4
E 2 0 0
E 6 1 0
E 6 1 1
E 6 2 0
E 6 2 0
E 9 1 0
DCR-HC1000/HC1000E
Symptom/State
0 Non-standard battery is used.
0 Condensation.
0 Video head is dirty.
0 LOAD direction. Loading does not
complete within specified time
1 UNLOAD direction. Loading does not
complete within specified time
0 T reel side tape slacking when unloading.
1 Winding S reel fault when counting the
rest of tape.
2 T reel fault.
3 S reel fault.
4 T reel fault.
0 FG fault when starting capstan.
0 FG fault when starting drum.
2 FG fault during normal drum operations.
LOAD direction loading motor time-
0
out.
UNLOAD direction loading motor
1
time-out.
T reel side tape slacking when
0
unloading.
Winding S reel fault when counting the
1
rest of tape.
2 T reel fault.
3 S reel fault.
4 T reel fault.
0
FG fault when starting capstan.
0 FG fault when starting drum
FG fault during normal drum
2
operations
0 Data on A page or D page are rewriten.
Difficult to adjust focus
0
(Cannot initialize focus.)
Zoom operations fault
0
(Cannot initialize zoom lens.)
Steadyshot function does not work well.
0 (With pitch angular velocity sensor output
stopped.)
Steadyshot function does not work well.
1 (With yaw angular velocity sensor output
stopped.)
Abnormality when the power supply
1 capacitor of the flash unit is being
charged.
Use the info LITHIUM battery.
Remove the cassette, and insert it again after one hour.
Clean with the optional cleaning cassette.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Make data on A page and D page correct value.
Inspect the lens block focus MR sensor (Pin wg, wh of CN1010 of
VC-366 board) when focusing is performed when the focus ring is
rotated in the focus manual mode, and the focus motor drive circuit
(IC5102 of VC-366 board) when the focusing is not performed.
Inspect the lens block zoom MR sensor (Pin wd, wf of CN1010 of
VC-366 board) when zooming is performed when the zoom lever
is operated and the zoom motor drive circuit (IC5102 of VC-366
board) when zooming is not performed.
Inspect pitch angular velocity sensor (SE520 of SE-149 board)
peripheral circuits.
Inspect yaw angular velocity sensor (SE521 of SE-149 board)
peripheral circuits.
Checking or replacement of the flash unit.
1-5
ENGLISH JAPANESE
ENGLISH JAPANESE
Correction