Ice & Water Dispenser; How It Works - GE 49-60067 Use And Care Manual

AUTOMATIC ICEMAKER & DISPENSER

How it Works

The automatic icemaker makes ice continually. The dispenser
dispenses water, ice cubes or crushed ice through the freezer
compartment door. Here's how they work.
Water flows from the household supply through a
(1) dual solenoid valve
to the
3
(2) water tubing and to the
(3) automatic icemaker
as needed.
Water is frozen in the
(4) cube mold and ejected
7
into the
(5) storage bin where a
motor-powered auger
moves cubes forward.
6
Important Facts About Your Ice & Water Dispenser
• If this is your first icemaker you'll hear occasional sounds that
may be unfamiliar. These are normal ice-making sounds and are not
cause for concern.
• Your icemaker will produce eight cubes per cycle—approximately
120 cubes in a 24-hour period—depending on freezer compartment
temperature, room temperature, number of door openings and other
use conditions.
• Intermittent dispensing of ice is normal. If ice flow interruption is
more than brief, ice clump(s) may be the cause and should be
removed following instructions in this section.
• Avoid over-filling glasses with ice and using narrow or extra-tall
glasses. This can jam the chute or cause the door in the chute to
freeze shut. Periodically open the freezer compartment door and look
down into the chute. If ice is blocking the chute, poke it through with
a wooden spoon.
Before Using Your Icemaker and Dispenser
If you use your refrigerator before the water
connection is made, raise the ice access door
and make sure the icemaker feeler arm is in the
(up) position. When the water supply has
been connected to the icemaker, move the
feeler arm to the (down) position.
Feeler arm in
(up) position
stops icemaking
(on some models)
4
(6) tubing in the door and is dispensed when the dispenser pad is
5
(7) A light switch (on some models) turns the night light in the
2
The light also comes on when the dispenser pad is pressed.
The light in the dispenser should be replaced with a 10 watt maximum
bulb when it burns out.
If you cannot locate the correct bulb, see your local dealer.
1
• To help keep bits of ice from being sprayed beyond the glass,
place the glass close to the ice chute—but not so close that it blocks
out-coming ice.
• Add ice before adding beverage to prevent splashing.
• Beverages and foods should not be quick-chilled in the ice
storage bin. Cans, bottles or food packages in the storage bin may
cause the icemaker or auger to jam.
• Do not add ice from trays or bags to the storage bin. It may not
crush or dispense well.
CAUTION: Some products such as water ices should not be
consumed too cold.
At first there will be a delay before water is dispensed and ice is made.
On models with a water dispenser, if no
water is dispensed when the refrigerator is
first installed, there may be air in the water line
system. Press the dispenser pad for at least two
minutes to remove trapped air from the water
line and to fill the water system.
The ice cube mold will automatically fill with water AFTER cooling
to freezer temperatures. The first cubes normally freeze after
several hours.
NOTE: With a newly-installed refrigerator, allow about 24 hours
for the freezer compartment to get cold enough to make ice.
Feeler arm in
(down) position
begins icemaking
Cubes dispense through the chute in the door when the
dispenser pad is pressed.
When the Crushed pad is pressed (on some models), a
baffle channels cubes through the crusher and crushed ice falls
through a chute into the glass.
When the Water pad is selected (on some models), water
flows through the
pressed.
dispenser on or off.
Push the dispenser pad
until the water line is filled.
(continued next page)
7