Table of Contents
Advertisement
Quick Links
26 inch
Wide Screen LCD Television
Operating Instructions
Model: TC1572LCD
Please read these instructions carefully and retain for future reference.
For assistance during normal working hours (8:30am - 5pm, Mon - Fri) please
contact Oriental Pacific International Ltd.
New Zealand call: 0800 89 85 80
Email:
service@orientalpacific.com
Advertisement
Table of Contents
Summary of Contents for Oriental Pacific TC1572LCD
-
Page 1: Operating Instructions
Operating Instructions Model: TC1572LCD Please read these instructions carefully and retain for future reference. For assistance during normal working hours (8:30am - 5pm, Mon - Fri) please contact Oriental Pacific International Ltd. New Zealand call: 0800 89 85 80 Email: service@orientalpacific.com... -
Page 2: Important Safety Instructions
1.0 IMPORTANT SAFETY INSTRUCTIONS When using any electrical apparatus always observe safety regulations and use basic safety precautions to reduce the risk of fire, electric shock and personal injury, including the following: Read, Keep and Follow these instructions, heeding all Warnings. WARNING! No objects filled with liquid, such as vases, shall be placed on this equipment or in any position where liquid may fall into this equipment or any other electrical apparatus. - Page 3 spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. WARNING! For household use only, this apparatus is not intended for commercial use. WARNING! If this apparatus is to be used by a third party, please supply these instructions with it. WARNING! No liability will be accepted for any personal injury or damage caused by failure to follow these instructions.
-
Page 4: Table Of Contents
Table of Contents CONTENTS PAGE 1.0 Important Safety Instructions 2.0 Features & General Information 3.0 Unpacking & Assembly Procedure 4.0 Location & Components 4.1 Locating the unit 4.2 Components (front) 4.3 Components (rear) 5.0 Remote Control 5.1 Setup 5.2 Operating range 6.0 Remote Control Functions 6.1 Description 7.0 Setup... -
Page 5: Features & General Information
NOTE FOR WALL INSTALLATION an independent professional installation company is recommended. Warranty claims will become void if damage to unit is caused by improper wall installation. PLEASE CONTACT ORIENTAL PACIFIC for advice on wall mount installation: 0800 89 85 80 or email: service@orientalpacific.com... -
Page 6: Unpacking & Assembly Procedure
3.0 Unpacking the package WARNING! This equipment is heavy, please use 2 people to carry and handle with care. 1. Check all packages have been received. You should have 1 LCD Display with Desktop Base Carton, and 1 Wall Bracket Assembly Carton. And the accessories: 1 x Instruction manual 1 x Remote control... -
Page 7: Location & Components
4.0 LOCATION & COMPONENTS Please read safety instructions for specific installation safety. 4.1 LOCATING THE UNIT (BASE MOUNT ONLY) Place on the floor or a sturdy platform only. Do not place in an area of foot traffic. Ensure the set cannot be accidentally knocked over. -
Page 8: Components (Rear)
4.3 COMPONENTS (BACK) Located on the back of the set are the following controls. S-Video Input SCART 2 Input (AV2) SCART 1 Input (AV1) RS232C Input (factory use only) DVI Input PC VGA Input Antenna Input Y/Pb/Pr/Y/Cb/Cr Input Audio Input... -
Page 9: Remote Control
5.0 REMOTE CONTROL 5.1 SETUP Your remote controller offers all the functions needed to operate this set. Please note that in standby mode the set is still connected to the mains supply. The remote requires two “AAA” size batteries to operate. To fit simply slide the back cover off the remote and install the batteries as directed. -
Page 10: Remote Control Functions
6.0 REMOTE CONTROL FUNCTIONS 6.1 DESCRIPTION Power: On/Off Standby mode Channel 1-9: Direct channel selection buttons Red, Green, Yellow, Blue: Fast text Recall: Return to previous channel Display: Display current channel & input mode P.Mode: Select picture mode S.Mode: Select sound mode Text: Enter Teletext mode Mute: Mute sound Menu: Call up / Hide main menu... -
Page 11: Setup
7.0 SETUP This set can be connected to most entertainment systems, such as normal television input, DVD, VCR, amplifier, computer, satellite input and camcorder. 7.1 CONNECTION Step 1. BASIC CONNECTION For basic television setup direct to a normal TV antenna, simply connect your outdoor antenna supply lead (not supplied) directly to the antenna input socket (17). -
Page 12: Tuning Tv
8.0 TUNING TV Step 1. TV SIGNAL SOURCE SELECTION To select the desired signal source by remote control (Selecting what you want to watch i.e. TV, • • • • DVD, Video etc) Press the “VIDEO” button until you enter TV mode •... - Page 13 TUNING TV Step 4. TV SOUND SYSTEM SELECTION To select “B/G” Sound system by remote control • • • • Press the “Menu” button to enter the main menu • • • • Press the “VOL+” or “VOL-“ button to navigate across •...
-
Page 14: Dvd Connection Setup
9.0 DVD CONNECTION SETUP For alternative set ups please see details below. The first example is for a DVD player. Some references to input & output sockets may vary to those on your associated equipment. Do not connect to the mains supply until all the connections have been made correctly. 9.1 DVD QUICK SETUP GUIDE Step 1. -
Page 15: Scart Connection
DVD CONNECTION SETUP Step 2. DVD SIGNAL SOURCE SELECTION To select the desired DVD signal source by remote control. Press the “Video” button until to enter AV1 or AV2 mode • • • • If the Y/Pb/Pr/Y/Cb/Cr connections are set up then you can press the “YpbPr” button to select HDTV mode instead of AV mode. -
Page 16: Operating Guide
10.0 OPERATING GUIDE Power ON / OFF: • Connect the LCD TV to power outlet and turn on the power switch. The power switch – On/Off (20) is located under front edge of panel. The power indicator will be red and then turns to blue. -
Page 17: Volume Adjustment
OPERATING GUIDE 10.3 VOLUME ADJUSTMENT Press “VOL+” or “VOL-“ button on the remote control to raise or lower the volume level. You can also change the volume by using the identical buttons located on the bottom of the front panel. 10.4 RECALL Press the “Recall”... -
Page 18: Still Mode
OPERATING GUIDE 10.8 STILL MODE To take a snapshot of the current picture on the screen. Press the “Still” button on the remote to freeze the picture, press the button again to return to normal viewing. NOTE: It is only the picture that is frozen, the TV or DVD will continue playing but you will see only the frozen image until you press the Still button again to return to normal viewing. -
Page 19: Using The Channel Menu
11.0 USING THE CHANNEL MENU 11.1 SKIP Use this function to delete any unwanted channel programmes found when using Auto search. Press the “Menu” button to enter the main • • • • menu Press the “VOL+” or “VOL-“ button to navigate •... -
Page 20: Manual Search
USING THE CHANNEL MENU 11.4 MANUAL SEARCH Press the “Menu” button to enter the main menu • • • • Press the “VOL+” or “VOL-“ button to navigate across the menu bar until you get to ‘CHANNEL’ • • • • Press “CH+”... -
Page 21: Using The Picture Parameters Menu
12.0 USING THE PICTURE PARAMETERS MENU 12.1 ADJUSTING PICTURE SETTINGS Press the “Menu” button to enter the main • • • • menu Press the “VOL+” or “VOL-“ button to • • • • navigate across the menu bar until you get to ‘PICTURE PARAMETERS’... -
Page 22: Using The Pip (Picture In Picture) Menu
14.0 USING THE (PICTURE IN PICTURE) MENU Optional PIP (Picture in Picture) function, when connected to more than one source of input signal. 14.1 SELECTING PIP SIZE MODE Press the “Menu” button to enter the main menu • • • • Press the “VOL+”... -
Page 23: Using The Sleep Menu
15.0 USING THE SLEEP MENU 15.1 SELECTING SLEEP MODE Press the “Menu” button to enter the main • • • • menu Press the “VOL+” or “VOL-“ button to • • • • navigate across the menu bar until you get to ‘SLEEP’... -
Page 24: Teletext Operation
17.0 TELETEXT OPERATION TO ENTER TELETEXT MODE Select a channel that is broadcasting Teletext. Press the “TEXT” button on the remote control to enter Teletext mode. To exit Teletext mode press the button again. The functions listed below are all under the Teletext mode, there are also four Teletext buttons located on the remote control. - Page 25 TELETEXT OPERATION SUB CODE Some Teletext pages contain sub pages that require the input of the sub page code. Press the “SUB CODE” until ‘Pages/Sub Pages’ is displayed. Then enter the four-digit sub code for the page needed. To quit simply press the “SUB CODE” button again. To show both normal TV picture and transparent Teletext, press the “MIX”...
-
Page 26: Troubleshooting
18.0 TROUBLESHOOTING Before calling for service please refer to the following basic troubleshooting guide for help. Ensure the supply cord is plugged in and switch on. TV WILL NOT TURN ON Ensure there is power to the circuit. Ensure the remote control batteries are not dead Ensure that the timer is not in operation. -
Page 27: Specifications
20.0 SPECIFICATIONS Display Size 26 inches (66cm) TFT LCD System Multi Standard (PAL, SECAM and NTSC playback) Channel Coverage VHF-L, VHF-H, UHF Resolution 1280 x 768 PC mode (VGA) 640x480/60Hz, 800x600/60Hz, 1024x768/60Hz, 1280x1024/60Hz Contrast 400:1 Brightness 450cd/m Respond time 16ms Non-conforming Pixel ≤... -
Page 28: Guarantee Card
In the unlikely event of a deficiency, please contact the retailer from whom this product was purchased. WARRANTY FOR APPLIANCES USED COMMERCIALLY LIMITED TO 90 DAYS Type of Appliance: 26 inch Wide Screen LCD Television. Model Mo.: TC1572LCD Purchase Date: Product Purchased From: Your Name:...