AT&T CRL81112 Quick Start Manual

Quick start guide
CRL81112/CRL81212
This quick start guide provides you with basic instructions only.
For more complete instructions, refer to your Abridged user's
manual provided in the package, or see the online Complete
user's manual at www.telephones.att.com/manuals.
Telephone base installation
Plug the telephone
base power adapter
into an electrical
outlet not controlled
by a wall switch. .
Raise the
Charger installation
antenna.
Plug the power
adapter into an
electrical outlet
not controlled by
a wall switch.
Plug the power cord and telephone
line cord into the jacks.
Caution: Use only the power adapter provided with this product. To obtain a replacement, visit
www.telephones.att.com
our website at or call
1 (866) 288-4268
In Canada, dial .
Battery installation
Install the battery as shown below. Charge your handset(s) before initial use.
The battery is fully charged after 10 hours of continuous charging.
1 2
2. Align the cover flat
1. Plug the battery
connector securely against the battery
compartment, then
into the socket inside
the handset battery slide it upwards
compartment. Insert until it clicks into
place.
the supplied battery
with the label THIS
SIDE UP facing up as
indicated.
Use only the supplied rechargeable battery or replacement battery (model BT183342).
Quick reference guide
CHARGE indicator
On when the handset is charging
in the telephone base or charger.
q
CID/VOLUME
• Show caller ID history.
• Scroll down in menus.
Plug one end of • Move cursor to the left when
entering names or numbers.
the telephone
• Decrease listening volume when
line cord into a
on a call.
telephone jack or
a DSL filter.
REDIAL/PAUSE
• Press repeatedly to view the last
If you have DSL
10 numbers dialed.
high-speed Internet
• Press and hold to insert a dialing
service, a DSL
pause while entering numbers.
filter (not included)
PHONE/FLASH
is required. The
DSL filter must be • Make or answer a call.
plugged into the
• Answer a call waiting call during
telephone wall jack.
a call.
1
• Press repeatedly to add or
remove 1 in front of the call log
entry before dialing or saving it
Route the
to the directory.
cords through • Press and hold to set or dial your
voicemail number.
the slots.
TONE
Press to switch to tone dialing
temporarily during a call if you have
pulse service.
1 (800) 222-3111
.
/SPEA�ER SPEA�ER
Switch between the speakerphone
and handset.
3
Handset
side view
Telephone
base
3. Charge the handset by
placing it face forward
in the telephone base
or charger.
Audio Assist ® is a registered trademark of Advanced American Telephones.
pDIR/VOLUME
• Show directory entries.
Handset • Scroll up in menus.
• Move cursor to the right when
entering names or numbers.
• Increase listening volume when
on a call.
SELECT/MENU
Show the menu.
•
• Select an item or save an entry
or setting while in the menu.
OFF/CANCEL
• Hang up a call.
• Press to cancel an operation,
back up to the previous menu,
or exit the menu display, or
press and hold to return to
idle mode.
• Press and hold in idle mode to
erase the missed call indicator.
QUIET # (pound key)
• Press repeatedly to display
other dialing options when
reviewing a caller ID log entry.
Press and hold to enter the
•
QUIET mode setting screen, or
to deactivate QUIET mode.
®
AUDIO ASSIST
Voices will sound louder and
clearer when you press
®
AUDIO ASSIST while you are
on a call using the handset.
MUTE/DELETE
• Mute the microphone during a call.
Delete the displayed entry while in the
•
directory, call log or redial list.
• Delete digits or characters when using
the dialing keys.
EQ
Change the audio quality to best
suit your hearing.
IN USE indicator
• On when the handset is in use.
• On when a handset is being
registered.
• Flashes when there is an incoming
call or when handsets are being
deregistered.
• Flashes when another telephone is
in use on the same line.
HANDSET LOCATOR
• While the telephone is idle, press
to page all handsets.
• Press and hold to begin handset
deregistration.
Initial settings
We recommend you program your telephone system before use.
The following are a few examples of common features to set before using
the telephone. Refer to the Handset settings in the Abridged user's manual
or the online Complete user's manual for detailed instructions on setting all
telephone features.
Set date/time
Set the date/time before using the telephone.
1. MENU -> q or p -> Set date/time -> SELECT.
2. Enter the month, day and year using the dialing keys -> SELECT.
3. Enter the hour and minute using the dialing keys.
4. q or p to choose AM or PM -> SELECT.
Handset ringer volume
You can set the ringer volume level to one of the six levels or turn the
ringer off.
1. MENU -> q or p -> Ringers -> SELECT.
2. SELECT to select Ringer volume.
3. q or p to choose the desired level -> SELECT.
Language
If you have accidentally changed the screen display language and want to
switch it back to English, follow the steps below.
• MENU in idle mode -> enter -> enter 364#.
Telephone operation
Operation Steps
Making a call Press PHONE or /SPEA�ER SPEA�ER -> Enter the telephone
number.
On-hook dialing Enter the telephone number -> Press
(predialing) /SPEA�ER SPEA�ER to call.
Answering a call PHONE or /SPEA�ER SPEA�ER, or press any dialing key
Press
(0-9, TONE or #).
Ending a call
Press OFF or return the handset to the telephone base
or charger.
Speakerphone During a call, press /SPEA�ER SPEA�ER to switch between
handsfree speakerphone and normal handset use.
Redial Press REDIAL repeatedly to select the desired entry
-> PHONE or /SPEA�ER SPEA�ER to call.
Volume control Press VOLUMEq to decrease or press VOLUMEp to
increase the listening volume during a call.
Call waiting Press FLASH to put current call on hold and to take the
(Requires subscription
new call; press again to switch back and forth between
from telephone
calls.
service provider)
PHONE or