Fini RD 185-810 User Manual page 28

40069 Zola Predosa (BO) - ITALY
DATABASE
Below is a list of the parameter description, type and address of data on DMC20 :
Data Description
DewPoint DewPoint temperature - T1 probe
Temperature of the incoming air - T2 probe
Air →O
Temperature of the outgoing air - T3 probe
Air ←O
Compr.LP Suction temperature of the compressor (low pressure side) - T4 probe
Compr.HP Outlet temperature of the compressor (high pressure side) - T5 probe
Condens. Condensing temperature - T6 probe
Inlet temperature of the cooling water (Water-Cooled) - T8 probe
Water →O
Ambient Ambient temperature - T7 probe
1)
Language Selection of the language for dialogue and alarm messages
DewPoint Set Not Used
Diff. DewPoint Not Used
E Drain Time Not Used
E Drain Pause Not Used
S Drain Time Discharge time of the condensate separator
S Drain Pause Pause between two condensate separator discharges
Display Contrast. Adjustment of the Display contrast
Min DewPoint Not Used
Max DewPoint Not Used
Low DewPoint Temperature of interv. for the too low DewPoint alarm
Low DP Diff.! Differential temperature for the too low DewPoint alarm
Low DP Delay! Delay time for the too low DewPoint alarm
High DewPoint ! Temperature of interv. for the too high DewPoint alarm
High DP Diff.! Differential temperature for the too high DewPoint alarm
High DP Delay! Delay time for the too high DewPoint alarm
Condensation ! Temperature of intervention for the too high DewPoint alarm
Condens.Diff.! Differential temperature for the too high DewPoint alarm
Condens.Delay! Delay time for the too high DewPoint alarm
Peripheral No Unit address for serial communication
Working Operating time of the dryer in hours
Alarm STOP Presence of an alarm that has stopped the dryer
Alarm Status Presence of an alarm
Cond. Fan Switch Status of the condenser fan control pressure switch
Remote ON/OFF Status of the Remote ON/OFF switch
Switch
DewPoint LOW Low DewPoint alarm ON
DewPoint HIGH High DewPoint alarm ON
Condens. HIGH High Condensation temperature alarm ON
STOP Compr.LP Cooler low pressure switch (P
STOP Compr.HP Cooler high pressure switch (P
Protection Fan. Fan thermal/electrical protections alarm ON (Air-Cooled)
Protection Comp. Compressor thermal/electrical protections alarm ON
Probe Fault Probe faulty alarm ON
Stop ! Low DP STOP enabled in case the DewPoint of the dryer is too low
Stop ! High DP STOP enabled in case the DewPoint of the dryer is too high
Automatic Machine enabled to restore its operation after a power black out
Start-up
Recovery After ! Automatic alarms reset
Autom.
ON/OFF DMC20 Status of DMC20 - ON or OFF (Stand-by)
1)
NOTE : Language selection : 00=Italian - 01=English - 02=German - 03=French
R=Read - W=Write
info@finicompressors.it
) alarm ON
B
) alarm ON
A
- EN -
Type Register
Address
Signed Integer 0000 - R
Signed Integer 0001 - R
Signed Integer 0002 - R
Signed Integer 0003 - R
Signed Integer 0004 - R
Signed Integer 0005 - R
Signed Integer 0006 - R
Signed Integer 0007 - R
Signed Integer 0200 - R/W
Signed Integer 0201 - R/W
Signed Integer 0202 - R/W
Signed Integer 0203 - R/W
Signed Integer 0204 - R/W
Signed Integer 0205 - R/W
Signed Integer 0206 - R/W
Signed Integer 0207 - R/W
Signed Integer 0208 - R/W
Signed Integer 0209 - R/W
Signed Integer 0210 - R/W
Signed Integer 0211 - R/W
Signed Integer 0212 - R/W
Signed Integer 0213 - R/W
Signed Integer 0214 - R/W
Signed Integer 0215 - R/W
Signed Integer 0216 - R/W
Signed Integer 0217 - R/W
Signed Integer 0218 - R/W
Signed Integer 0219 - R/W
Signed Integer 0246 - R/W
bit - 1=Yes 0100.0 - R
bit - 1=Yes 0100.1 - R
bit - 1=ON 0101.3 - R
bit - 0=Local 0101.6 - R
1=Remote
bit - 1=Yes 0102.0 - R
bit - 1=Yes 0102.1 - R
bit - 1=Yes 0102.2 - R
bit - 1=Yes 0102.4 - R
bit - 1=Yes 0102.5 - R
bit - 1=Yes 0102.6 - R
bit - 1=Yes 0102.7 - R
bit - 1=Yes 0102.8 - R
bit - 1=Yes 0220.0 - R/W
bit - 1=Yes 0220.1 - R/W
bit - 1=Yes 0220.2 - R/W
bit - 1=Yes 0220.3 - R/W
bit-1=Stand-by 0220.15 - R/W