Maytag CGR1425ADT User's guide Manual page 20

Se f-C ean Oven (select models)
Note: For manual dean oven, see page 22. [
o it is normal for parts of the rang e to become hot dul ng a
6. Wipe up sugary and acidic spiHovers such as sweet
potatoes, tomato, or miik-based sauces. Porceiain ename]
is add-resbtant, not acid-proof. The porceiain finish may
discobr if acidic spills are not wiped up before a serif-
dean cycb.
To set Self-Clean:
- To prevent personal injur_ and damage to the oven door
do not attempt to open door when "LOCK" is disphyed
• Avoid touching cooktop, door window or oven vent area
during a dean cycle.
• Do not use commercial oven cleaners on the oven finish
or around any part of the oven. They will damage the
finish or parts.
The self-clean cycle uses above-normal cooking temperatures
to automatically clean the oven interior. Do not force the oven
door or lock lever open. This may result in exposure to high
temperatures and be a burn hazard.
It is normal for flare-ups, smoking, or flaming to occur during
cleaning if the oven is heavily soiled. It is better to clean the
oven regularly rather than to wait until there is a heavy build-
up of soil in the oven.
During the cleaning process, the kitchen should be well
ventilated to get rid of normal odors associated with cleaning.
Before Seff-C eaning
1. Turn off the oven light before cleaning. The light may burn
out during the clean cycle.
2. Remove broiler pan, all pans, and oven racks from the
oven. The oven racks will discolor and may not slide easily
after a self-clean cycle if they are not removed.
3. Clean oven frame, door frame, area outside of gasket, and
around the opening in the door gasket with a nonabrasive
cleaner such as Bon Ami* or detergent and water. The
self-cleaning process does not
clean these areas. They should be
cleaned to prevent soil from baking
on during the clean cycle. (The
gasket is the seal around the oven
door and window.[}
4. To prevent damage, do not clean or
rub the gasket around the oven
door. The gasket is designed to seal in heat during the
clean cycle.
5. Wipe up excess grease or spillovers from the oven bottom.
This prevents excessive smoking, flare-ups or flaming
during the clean cycle.
Note: Oven temperature must be below 400° F to program
a clean cycle.
1. Close the oven door.
2. Move door lock lever right to the locked position.
3. Press the CLEAN pad. CLEAN
, CLEAN flashes in the display.
If the door is not closed, beeps wiii sound and DOOR wiii
display. If the door is not closed within 45 seconds, the
self-cleaning operation wiii be canceled and the display
will return to the time of day.
4. Press the A or V pad. ........
° CL-M (Clean - Medium Soil} is displayed.
5. Press the A or V pad to scroii through the
self-cleaning settings.
CL-H {Clean - Heavy'Soil, 4 hours}
CL-M (Clean - Medium Soil, 3 hours}
CL-L (Clean - Light Soil, 2 hours}
Choosing the soil level of the oven automatically programs
the self-cleaning time.
6. After four seconds, the oven will start cleaning.
° The cleaning time will start counting down in the display.
° LOCK wiii appear in the display.
° CLEAN wiii appear in the display.
To Delay a Self-CJean Cycle:
1. Press the DELAY pad.
° DELAY flashes.
2.
DELAY
, 00:00 wiii appear in the display.
Press the A or V pad to set the amount of time you want
to delay the cycle. Delay time can be set from ten minutes
@0:10} to 11 hours, 59 minutes (11:59}.
conto
* Brand names for cleaning products are registered trademarks of the respective manufacturers,
19