Table of Contents
Advertisement
Serial Number Decal
BELT/CHAIN DRIVE
GARAGE DOOR OPENER MODELS
Model 1028
Model 2028
OPERATION &
MAINTENANCE
MANUAL
Includes Intellicode® Remote Control. Safe-T-Beam® System must be installed to close the door. For use only with residential
sectional overhead garage doors. Homelink® and Car2U® compatible
STOP
INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER
HOMEOWNER: SAVE THIS MANUAL FOR FUTURE REFERENCE
To reduce the risk of injury to persons or damage to property, use this opener only with a sectional residential door.
Por réduire le risque de blessures ou de dommages materials, utilisez cet ouvre-porte uniquement pour une porte à section ré sidentielle.
©2015 The Genie® Company, the Genie Logo, Intellicode® and Safe-T-Beam®, are trademarks of GMI Holdings, Inc. d/b/a The Genie® Company.
All other trademarks are property of their rightful owners. Consistent with our policy of continuing product improvements, we reserve the right to change product speci cations without
prior notice or obligations. HomeLink is a registered trademark of Gentex Corporation. Car2U is a registered trademark of Lear Corporation.
Need help or have questions?
For answers and assistance,
visit www.GenieCompany.com
or call Customer Service at: 1-800-35-GENIE
WARNING
AVERTISSEMENT
PRE-PROGRAMMED
REMOTE
INCLUDED
FOR QUICK
& EASY
INSTALL
38484502553
Advertisement
Table of Contents
Related Manuals for Genie 1028
Summary of Contents for Genie 1028
- Page 1 Por réduire le risque de blessures ou de dommages materials, utilisez cet ouvre-porte uniquement pour une porte à section ré sidentielle. ©2015 The Genie® Company, the Genie Logo, Intellicode® and Safe-T-Beam®, are trademarks of GMI Holdings, Inc. d/b/a The Genie® Company.
-
Page 2: Table Of Contents
Important Safety Instructions ......14 Regular Maintenance ..........15 If you are a homeowner/end user and need help or have questions: Remote Battery Replacement ......15 call 800-35-GENIE. Light Bulb Replacement ........16 Or visit: www.GenieCompany.com Chain/Belt Tension ..........16 Do not return product to the store. -
Page 3: Safety Information
Safety Information OVERVIEW OF POTENTIAL HAZARDS READ THIS SAFETY INFORMATION Garage doors are large, heavy objects that move with the help of springs under high tension and electric motors. Since moving objects, springs under tension, and electric motors can cause injuries, your safety and the safety of others depend on you reading the information in this manual. If you have questions or do not understand the information presented, call your nearest trained door system technician or visit our website at www.GenieCompany.com. -
Page 4: Important Installation Instructions
POUR RÉDUIRE LES RISQUES DE BLESSURES GRAVES VOIRE MORTELLES LIRE ET SUIVRE ATTENTIVEMENT TOUTES LES INSTRUCTIONS D’INSTALLATION ET DE FONCTIONNEMENT AINSI QUE TOUTES LES CONSIGNES DE SÉCURITÉ. Si vous avez des questions ou si vous ne comprenez pas une instruction, veuillez contacter directement The Genie Company. •... -
Page 5: Features
Features Begin here ONLY AFTER completing assembly and installation of the opener. Review the Assembly and Installation Poster to ensure all steps have been performed. Visit www.GenieCompany.com to download a printable le. SAFETY FEATURES OPENER FEATURES Safe-T-Beam® (STB) Non-Contact Intellicode® Reversing System An encryption system that enhances the security Puts an invisible beam across the door... -
Page 6: Wall Console Features
Wall Control Features One of the following wall controls will be included. NOTE: Wall consoles from other manufacturers may not work with this new opener. Use only the wall control provided with this unit. See warning. SERIES II WALL CONSOLES Open/Close Button Opens and closes door from inside garage. -
Page 7: Introduction
Programming Overview NOTE: Before programming the operator, check to make sure there are no objects in the garage door opening. INTRODUCTION Now that the garage door opener is installed, follow the steps in this manual to program the opener so that the door opens and closes properly and all remote devices operate correctly. -
Page 8: Travel Limits
DO NOT set limits with Power Sentinel attached. AC power les limites. Voir le poster d’installation (si fourni) ou appelez le MUST be connected to the opener while setting limits for service clientèle au 1-800-35-Genie ou visitez le site www. proper operation. -
Page 9: Opening Garage Door (Up Limit)
Programming Information Opening Garage Door (Up Limit) NOTE: Beginning with garage door closed is recommended but not necessary. READ AND UNDERSTAND STEPS 6-9 BEFORE PROCEEDING 9. Press and release the program/set button—both LEDs 6. Press and hold the UP arrow button (+) for two seconds ash blue and then go o . or until the long LED comes on blue. -
Page 10: Force Control
Wall Control Operation Force Control Contact Reverse Test NOTE: The limit and Force settings MUST BE COMPLETED before The force controls are automatically set when the wall control is used performing the Contact Reverse Test. for the rst time with garage door opener. The door MUST complete one full cycle, from full open to full close and then, full close to full 12. -
Page 11: Remote Control Programming
Remote Control Programming REMOTES Slowly press and release the remote button two times. The opener LEDs will ash and go o , indicating it has been NOTE: THE REMOTE CONTROLS INCLUDED WITH THIS OPENER, HAVE successfully programmed to the remote. BEEN PRE-PROGRAMMED AT THE FACTORY FOR YOUR CONVENIENCE. -
Page 12: Programming Wireless Keypad
Programming Wireless Keypad (Optional on some models) Tip: Program Keypad before mounting. Keypad Overview: Synchronizing Keypad to Door 1. Press PROGRAM SET button two seconds until the round LED turns blue, then release. The long purple LED will blink. Flashing PRGM PRGM PRGM... - Page 13 Programming Wireless Keypad (Continued) Mounting Keypad Door Operation with Wireless Keypad: The keypad MUST be mounted within sight of the garage door(s) at To open and close a single door with the Keyless Entry Pad, enter least ve feet above the oor and clear of any moving door part. the PIN number and press Up/Down Key (enter).
-
Page 14: Programming Vehicle Remotes
1. Press and release button 1 again. C. Release the button being held step B and wait for the LED to stop ash- ing. This button is now set for Genie. Repeat Step 2 for second Genie Opener. -
Page 15: Clearing Memory For Remotes
Clearing Remotes CLEARING MEMORY OF REMOTES Press and hold the UP (+) and DOWN (–) button at the same time, until both LEDs ash blue and go o . NOTE: Clearing memory of remotes from the powerhead will clear ALL programmed remotes and wireless keypads. -
Page 16: Maintenance And Adjustments
Maintenance and Adjustments For help, call customer service at: 1-800-35-GENIE or visit www.GenieCompany.com IMPORTANT SAFETY INSTRUCTIONS IMPORTANTES CONSIGNES DE SÉCURITÉ WARNING AVERTISSEMENT POUR RÉDUIRE LE RISQUE DE BLESSURES GRAVES VOIRE MORTELLES, TO REDUCE THE RISK OF SEVERE INJURY OR LIRE ET COMPRENDRE TOUTES LES INSTRUCTIONS. -
Page 17: Regular Maintenance
Maintenance and Adjustments (continued) Regular Maintenance C. Safe-T-Beam (STB) System Check ® Basic monthly maintenance tasks include: Check that both the RED and GREEN LEDs are ON steady. This indicates • Contact Reverse Test the system is working properly. If both LEDs are not ON steady, check •... -
Page 18: Light Bulb Replacement
Maintenance and Adjustments (continued) F. LIGHT BULB REPLACEMENT WARNING AVERTISSEMENT • Use extreme caution when working from a ladder or step • Faire particulièrement attention lors de travaux e ectués stool or serious injury can occur. depuis une échelle ou en escabeau. •... -
Page 19: Adjustment Guides
Maintenance and Adjustments H. ADJUSTMENT GUIDES WARNING AVERTISSEMENT TO AVOID INJURY OR DAMAGE Pour éviter les blessures ou des dommages • NE JAMAIS régler la force pour compenser des dommages, • NEVER adjust the force settings to adjust for damage, y compris une porte mal équilibrée, un rail de porte coinçant including an unbalanced door, binding door track or ou des ressorts cassés. -
Page 20: Locating Safe-T-Beam
Maintenance and Adjustments Multiple Garage Doors LOCATING SAFE-T-BEAM® PAIRS • NEVER position Safe-T-Beam® modules where signals will cross. Transmitter (RED LED) and Receiver (GREEN LED) • Place the Source (Red LED) Safe-T-Beams on adjacent doors facing in opposite directions. NOTE: Direct sunlight creates interference with Safe-T-Beam ® sensors (Green LED). Sensor modules CAN be positioned further away from the door opening if necessary to avoid sunlight but no further o the wall to maintain alignment with the Source (Red LED) module. -
Page 21: Troubleshooting
Troubleshooting Need help or have questions? DO NOT RETURN to the store. Visit www.genicompany.com or call Customer Service at 1-800-35-GENIE. PROBLEM: WHAT TO DO: Opener does NOT • Turn Sure-Lock™ OFF See page 4. • Check power source. operator when wall – Plug a lamp into outlet used for powerhead. If lamp works, power source is OK. - Page 22 Troubleshooting Troubleshooting OPERATION (continued) PROBLEM WHAT TO DO • Be sure all door fasteners are tight. Noisy operation. • Be sure garage door is in good repair, properly lubricated and balanced. • Be sure opener is in good repair. Door opener runs • Check operating condition of door. Door may need professional repair/adjustment. slow. • Have you installed this opener on a one-piece door? This opener is not designed to operate a one-piece door. POWERHEAD LEDS Powerhead LED Solution Possible Problem Round LED Long LED Normal operation. None required. Check power supply. No response from unit.
-
Page 23: Warranty
Limited Warranty Models 1028 and 2028 GMI Holdings, Inc. d/b/a The Genie Company (“Seller”) warrants to the original purchaser of the Model 1028 or 2028 garage door opener (“Product”), subject to all of the terms and conditions hereof, that the Product and all components thereof will be free from defects in mate- rials and workmanship for the following period(s) of time, measured from the date of purchase: MOTOR/GEARBOX –... - Page 24 THE GENIE COMPANY 1 DOOR DRIVE MOUNT HOPE, OHIO. 44660 1-800-35-GENIE www.GenieCompany.com...