Page of 27
Download Table of contents Bookmark

Genie INTELLIG 1000 3024H Operation And Maintenance Manual

Genie garage door opener user manual.
IntelliG
1000
Model 3024 and 3024H
GARAGE DOOR OPENER
OPERATION AND MAINTENANCE MANUAL
Includes INTELLICODE
2 Remote Control. Safe-T-Beam
System must be installed to close door.
®
®
For use only with residential sectional or one piece overhead garage doors.
Homelink
and Car2U
compatible.
®
®
For Answers and Assistance:
1.800.354.3643
or visit www.geniecompany.com
WARNING: To reduce the risk of injury to persons or damage to property – Use this opener only with a one piece
or sectional door.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
INSTALLER:
LEAVE THIS MANUAL WITH HOMEOWNER
Homelink is a registered trademark of Johnson Controls Technology Company. Car2U is a registered trademark of Lear Corporation. © 2010 The Genie Company PN# 37066500753, 12/2010

   Related Manuals for Genie INTELLIG 1000 3024H

   Summary of Contents for Genie INTELLIG 1000 3024H

  • Page 1

    SAVE THIS MANUAL FOR FUTURE REFERENCE. INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER Homelink is a registered trademark of Johnson Controls Technology Company. Car2U is a registered trademark of Lear Corporation. © 2010 The Genie Company PN# 37066500753, 12/2010...

  • Page 2: Safety Information

    Could result in Death or Serious Could result in Death or Serious Could result in Death or Serious ©2010 The Genie Company SAFETY INFORMATION CONVENTIONS USED IN THESE INSTRUCTIONS Effect Keep people clear of opening while Door is moving. WARNING Do NOT allow children to play with the Door Opener.

  • Page 3

    Select units have motion detection built into the powerhead. Lights automatically turn ON when motion is detected for much safer movement through the garage. Lights will turn OFF after 4 minutes of no motion. ©2010 The Genie Company (Not available on all models)

  • Page 4: Table Of Contents

    Troubleshooting Guide - Powerhead LEDs ...25 Reference - Wiring Diagram ...26 Warranty ...27 OPENER MUST BE INSTALLED WITH THE INCLUDED WALL CONSOLE. ©2010 The Genie Company TABLE OF CONTENTS Safe-T-Beam® SAFETY REVERSE SYSTEM MUST BE INSTALLED TO CLOSE DOOR. 12/2010...

  • Page 5: Important Installation Instructions

    There are no assembly or installation steps included in this manual. Contact your Genie® Professional Dealer for an installation poster, if required, or visit www.geniecompany.com to download a PDF file. The following mechanical assembly tasks must be completed before continuing.

  • Page 6

    ©2010 The Genie Company 12/2010...

  • Page 7

    ©2010 The Genie Company 12/2010...

  • Page 8

    ©2010 The Genie Company 12/2010...

  • Page 9

    ©2010 The Genie Company 12/2010...

  • Page 10

    ©2010 The Genie Company 12/2010...

  • Page 11: Powerhead & Rail Assembled View

    REMARQUE: Utilisez la console sur le mur et les capteurs de sécurité fournis avec cet appareil. NE PAS substituer la console du mur ou les capteurs de sécurité. NOTA: Use la consola de pared y los sensores de seguridad proporcionados con esta unidad. NO sustituya la consola de pared ni los sensores de seguridad. ©2010 The Genie Company 12/2010...

  • Page 12: Typical Sectional Door Installation

    6 po (15 cm) MAX. - 5 po (12,7 cm) MIN. MAX. 6" - MIN. 5" FOR HELP-1-800-35-GENIE OR WWW.GENIECOMPANY.COM ...POUR OBTENIR DE L’AIDE-1-800-35-GENIE ... PARA OBTENER AYUDA, LLAME AL 1-800-35-GENIE OPTIONAL - HEADER BRACKET MOUNTING BOARD PLANCHE DE MONTAGE FACULTATIVE POUR SUP- PORT D’EMBASE...

  • Page 13: Typical One Piece Door Installation

    PALPEURS de SAFE-T-BEAM® SENSORES SAFE-T-BEAM® 12/2010 ... FOR HELP-1-800-35-GENIE OR WWW.GENIECOMPANY.COM ...POUR OBTENIR DE L’AIDE-1-800-35-GENIE ... PARA OBTENER AYUDA, LLAME AL 1-800-35-GENIE I F D O O R B E C O M P U L L E S O...

  • Page 14: Overview Of Powerhead Controls

    Program button Close Travel button Open Travel button LED Colors Round Red Round Purple Round Blue ©2010 The Genie Company Programming Overview There are four Powerhead program menus: Remote Program (Default menu) Limits Program Speed Program* Force Program* Programming steps for Limits and remotes are found on pages 6 through 10.

  • Page 15: Lost Or Stolen Remote - Clearing Memory

    • Connect the opener into an outlet on a circuit different from that to which the receiver is connected. • Consult your local dealer. ©2010 The Genie Company LOST OR STOLEN REMOTE - CLEARING MEMORY Clearing remotes from powerhead memory will clear ALL programmed remotes and wireless keypad.

  • Page 16: Intellicode® Features

    IntelliCode® selection for this 2 and/or 1 button is set to IntelliCode® 1. Use IntelliCode® 5. Take the remote to the older Genie® garage door opener and follow that opener's instructions to program a new remote. Repeat for other Genie® garage remote(s) as necessary.

  • Page 17: Maintenance & Troubleshooting, Important Safety Instructions

    Bestimmungen der USA und Kanadas abweichen. MAINTENANCE & TROUBLESHOOTING If you have any questions, please do not hesitate to contact customer service at: 1-800-35-GENIE IMPORTANT SAFETY INSTRUCTIONS WARNING: To reduce the risk of severe injury or death: 1.

  • Page 18: Contact Reverse Test, Routine Monthly Maintenance, Door Balance (spring Tension), Safe-t-beam® System Check

    Return to pages 6-7 and repeat steps 1 through 10 to correct down limit. ©2010 The Genie Company Use wall console supplied with opener. Other approved wall consoles may be available.

  • Page 19: Change Light Bulbs, Motion Detector - Overview, Reset - Open/close Travel Limit, Carriage Engage/disengage

    (pages 6-7) erases previous Limits/Force settings. NOTE: The opener will not close the door automatically unless the Safe-T-Beam® System is installed and Limits are programmed. ©2010 The Genie Company CARRIAGE ENGAGE/DISENGAGE Use Release Handle to manually connect or release chain or belt bullet to Carriage.

  • Page 20: Wall Console - Overview, Optional Dual Wall Console - Installation

    Follow the instructions on this page. Wall consoles from other manufacturers may not work with openers of these serial number groups. Genie® Series I wall buttons and Series II wall consoles will not work with openers of this serial number group.

  • Page 21: Remote Battery Replacement

    1. Open the remote case using a washer or coin that fits into the slot at the top of the remote. 2. Replace battery. 3. Align components and snap case closed. ©2010 The Genie Company Adjustment required Correctly adjusted Belt at center of rail...

  • Page 22

    Default LED display is the current Speed setting LED Speed indicator colors MAXIMUM SLOW ©2010 The Genie Company SPEED SETTINGS FOR HELP-1-800-35-GENIE OR WWW.GENIECOMPANY.COM CHANGE SPEED SETTING Use this guide to ADJUST powerhead SPEED settings.

  • Page 23

    Force Level 5 Force Level 6 Force Level 7 Force Level 8 Force Level 9 ©2010 The Genie Company - FORCE SETTINGS FOR HELP-1-800-35-GENIE OR WWW.GENIECOMPANY.COM CHANGE FORCE SETTING Use this guide to ADJUST powerhead FORCE settings. NOTE: There are nine (9) force levels.

  • Page 24

    Press and hold the wall console button until door is completely closed. malfunction. • Check for interference from adjacent Safe-T-Beam® units. • Contact The Genie Company at 1-800-35-GENIE. Door starts down, • Check Safe-T-Beam® wire connections at powerhead. See page 18.

  • Page 25: Troubleshooting Guide - Powerhead Leds

    ON/PURPLE/ FLASHING ON/RED/ FLASHING ON/RED/ FLASHING ON/RED/ STEADY ©2010 The Genie Company OPERATION (CONTINUED) ... FOR HELP-1-800-35-GENIE WHAT TO DO POWERHEAD LEDs Possible Problem Normal operation No response from unit Limits NOT set properly Program error Component failure Remote NOT programmed IntelliCode®...

  • Page 26

    BLANC BLANCO FIG. 6-5 WARNING AVERTISSEMENT ADVERTENCIA ELECTRICAL SHOCK CHOC ÉLECTRIQUE CHOQUE ELÉCTRICO ©2010 The Genie Company ... PARA OBTENER AYUDA, LLAME AL 1-800-35-GENIE CHAIN/BELT MOTOR CADENA/CORREA MOTEUR CHAÎNE/COURROIE MOTOR STRIPED WHITE BLANC RAYÉ BLANCO RAYADO WHITE BLANC BLANCO SAFE-T-BEAM®...

  • Page 27: Warranty

    GMI Holdings, Inc. d/b/a The Genie Company ("Seller") warrants to the original purchaser of the below identified garage door opener, IntelliG 3024 and 3024H) (“Product”), subject to all of the terms and conditions hereof, that the Product and all components thereof will be free from defects in materials and workmanship for the following period(s) of time, measured from the date of purchase: MOTOR/GEARBOX- Seller warrants the motor/gearbox for the LIFETIME* of the product.

Comments to this Manuals

Symbols: 0
Latest comments: