Professional line garage door opener user manual (27 pages)
Summary of Contents for Genie 7035-TKV
Page 1
User Manual of Product 1: Genie Chain Drive 750 3/4 HPc Garage Door Opener w/Battery Backup - Heavy Duty Chain Drive - Operate your garage door when the primary power is out - Wireless Keypad Included, Model 7035-TKV,BLACK User Manual of Product 2:...
Changes or modi cations not expressly Troubleshooting ........... 17-18 approved by the party responsible for compliance could void the user’s authority to Genie Battery Backup Installation ....19 operate the equipment. Optional Programming & Accessories FCC / IC Statement: Clearing Memory for Remotes ......20 This device complies with FCC Part 15 Programming Vehicle Remotes ......21...
Page 4
Before setting up your new garage door opener, please locate and record the model plate on the opener. This information will be necessary should you seek technical support via our website, customer support department or local servicing Genie dealer. Model Number...
SAFETY NOTIFICATIONS & INSTRUCTIONS OVERVIEW OF POTENTIAL HAZARDS READ THIS SAFETY INFORMATION Garage doors are large, heavy objects that move with the help of springs under high tension and electric motors. Since moving objects, springs under tension, and electric motors can cause injuries, your safety and the safety of others depend on you reading the information in this manual. If you have questions or do not understand the information presented, call your nearest trained door system technician or visit our website at www.geniecompany.com.
MORTELLES LIRE ET SUIVRE ATTENTIVEMENT TOUTES LES INSTRUCTIONS D’INSTALLATION ET DE FONCTIONNEMENT AINSI QUE TOUTES LES CONSIGNES DE SÉCURITÉ. Si vous avez des questions ou si vous ne comprenez pas une instruction, veuillez contacter directement The Genie Company. • NE PAS installer l’opérateur sur une porte mal équilibrée. Celle-ci pourrait entraîner de graves blessures. Les réparations et les réglages des câbles, ensembles de ressort ou tout autre article de quincaillerie doivent être e ectués par un pro-...
Genie Battery Backup (BBU) Available on some models. Provides power to opener in the event of a power failure. NOTE: Genie Battery Backup will only operate after opener installation is completed and Travel Limits have been set. DO NOT INSTALL BATTERY BACKUP UNTIL OPENER IS FULLY INSTALLED AND PROGRAMMED...
INTRODUCTION Now that the Genie® garage door opener is installed, follow the steps in this manual to program the opener so that the door opens and closes properly and all remote devices operate correctly.
La tendeur DOIT être engagée dans le chariot AVANT de régler les limites. Voir le poster d’installation (si fourni) ou RELEASE appelez le service clientèle au 1-800-35-GENIE ou visitez le site www.GenieCompany.com. • NE PAS xer de limites en mode batterie de secours.
PROGRAMMING UP TRAVEL LIMIT Programming UP Limit: 1-2. Enter Programming Mode HOLD 1. Press and hold the UP arrow button. UNTIL • Long LED will light BLUE. 2. Release UP arrow button. Lights • Round LED will ash BLUE. 3. Press and hold the UP arrow button until door is Steady Blue fully open.
PROGRAMMING FORCE AND CONTACT REVERSE Force Control Contact Reverse Test The force controls are automatically set when the NOTE: The limit and Force settings MUST BE COMPLETED wall control is used for the rst time with garage before performing the Contact Reverse Test. door opener.
PROGRAMMING ADDITIONAL REMOTE CONTROLS 1. Activate Remote THE REMOTE CONTROLS INCLUDED WITH THIS OPENER HAVE BEEN PROGRAMMED AT THE FACTORY FOR YOUR CONVENIENCE. NOTE: The following instructions are for remote control transmitters purchased separately in addition to those provided with this opener, but can also be used if any remote(s) may require re-programming.
IMPORTANT SAFETY INSTRUCTIONS WARNING To reduce the risk of severe injury or death, read and follow all instructions. NEVER let children operate or play with the door controls. Keep remote away from children. ALWAYS keep the moving door in sight and away from people and objects until door is completely closed. NO ONE SHOULD CROSS THE PATH OF THE MOVING DOOR.
MAINTENANCE & ADJUSTMENTS AVERTISSEMENT WARNING L’utilisation d’une autre commande murale pourrait produire des résultats inattendus de la Use of any other wall control can cause unexpected operation of the door and loss of lighting feature. Locate wall console within sight of the door but far porte ainsi que le dysfonctionnement de l’éclairage.
NOTE: SilentMax Connect™ models require a minimum 40 Watt or equivalent bulb, 60 watt maximum. * Genie LED light bulbs are designed to reduce or eliminate reduced remote range issues caused by common LED bulbs. They also o er better product life by making them resistant to vibration caused by the opener, and cold or damp weather.
Rail, Chain, & Door The carriage on this opener can be adjusted to work with the Emergency Arms not shown for Release Cable Lock System (available at your local Genie® Retailer). clarity Operate door to mid position. Pull emergency release cord and manually close door.
MAINTENANCE & ADJUSTMENTS Multiple Garage Doors LOCATING SAFE-T-BEAM® PAIRS • NEVER position Safe-T-Beam® modules where signals will cross. Transmitter (RED LED) and Receiver (GREEN LED) • Place the Transmitter (Red LED) Safe-T-Beams on adjacent doors facing in opposite directions. ® NOTE: Direct sunlight creates interference with Safe-T-Beam Receiver (Green LED).
TROUBLESHOOTING Need help or have questions? DO NOT RETURN to the store. Visit www.genicompany.com or call Customer Service at 1-800-35-GENIE. PROBLEM: WHAT TO DO: • Turn Sure-Lock™ OFF See page 6. Opener does NOT • Check power source. operate when wall –...
Page 19
TROUBLESHOOTING POWERHEAD LEDS Powerhead LED Solution Possible Problem Round LED Long LED Normal operation. None required. Check power supply. No response from unit. Contact a trained door system professional. ON/RED/ ON/RED/ Limits NOT set properly. Re-program limits, see pages 8-9. STEADY STEADY Program error.
GENIE® BATTERY BACKUP INSTALLATION Battery backup devices from other manufacturers will not operate with this opener. Use only Genie Battery Backup type battery that was provided. Genie P/N 111658-0002 Installing Genie Battery Backup TO PREVENT POSSIBLE CAUTION SERIOUS INJURY or DEATH...
OPTIONAL PROGRAMMING & ACCESSORIES CLEARING MEMORY OF REMOTES 2. Press and Hold + & - Buttons NOTE: Clearing memory of remotes from the powerhead will clear ALL programmed remotes, wireless keypads and vehicle transmitters. The opener will no longer recognize any signal from any remote device, including a missing remote device.
LEDs will light solid red. B. Press the chosen HomeLink button for two seconds and release. Press B. Press and hold the button (2 or 3) to change it to Genie—the that same button again for two seconds and release. The long LED corresponding LED will ash.
The keypad is now programmed with a PIN number and set up for multi opener operation. Keypad is now ready to LED Flashing program to multiple Genie® Intellicode® garage door openers. Up/Down Key • If LED did not blink twice and shut o , please see RESETTING (enter) THE KEYPAD (FACTORY DEFAULT) section.
Page 24
WIRELESS KEYPAD PROGRAMMING STEP 3) OPERATING THE KEYPAD WITH THE OPENER(S) REPLACING BATTERIES Single Door Operation: If the keypad back-lighting fails to operate, Batteries may 1. Ensure number pad back lighting is o . require replacement. 2. Enter PIN number. •...
REPLACEMENT PARTS Item # Part Number Description............Qty. ORANGE BAG 39010R.S PARTS PK,MOUNTING,ORANGE ... 1 TURNBUCKLE ...........1 Cotter Pin (x2) Clevis Pin 5/16 x 1.75 (x2) PIN,CLEVIS,5/16 X 1-3/4 .........2 COTTER,HAIRPIN,.0725 DI .......2 5/16" x 1-3/4" BOLT,HH,PLD,5/16-18 X 2 ........1 Header bracket 1/4"- 20 - 3/4"...
Page 26
REPLACEMENT PARTS Item # Description Qty. 5-pcs. Rail Assembly Complete (Chain) 5-pcs. Rail Assembly Complete (Belt) Sprocket Support Assembly (Chain) Sprocket Support Assembly (Belt) Carriage Assembly Idler Pulley Chain Assembly (7Ft) Belt Assembly(7Ft) Door Arm,Curved Door Arm,Straight Strap,Hanging,3/4 X 25. 90 Ft.
Page 27
SINGLE BULB POWERHEAD Item # Description QTY. COVER,SINGLE BULB LENS MOTOR ASSEMBLY SOCKET,LIGHT,30 DEG ANG TRANSFORMER,120VAC PCBA,DC CONTROLLER POWER CORD,45” SCR,M6-1 X 12 HWH THDF (3pk.) SCR,HHD,SLTD,TAP,#8X5/1 (3pk) Optical Encoder Assembly Specify model number when ordering parts from Genie Customer Care.
Page 28
COVER, DUAL BULB LENS MOTOR ASSEMBLY SOCKET,ANGLED LIGHT TRANSFORMER,120VAC PCB, DC CONTROLLER POWER CORD,45” SCR,M6-1 X 12 HWH THDF (3pk) SCR,HHD,SLTD,TAP,#8X5/1 (3pk) ICDM BOARD (Integrated Aladdin Models Only) OPTICAL ENCODER ASSEMBLY Specify model number when ordering parts from Genie Customer Care.
DASMA INFORMATION IMPORTANT Garage Door Openers Are Not Toys INFORMATION Automatic Garage Door Opener Garage Door Safety and Maintenance Guide Do not stand or walk under a moving door! Do not let children or adults play “beat the door. ” It is dangerous and can result in serious injury or death.
Page 30
Teach children to keep their hands and ngers clear of section joints, hinges, track, springs and other door parts. Contact with a moving door or its hardware could cause serious injury. The pushbutton wall control should These injuries can also happen be out of the reach of children (at with garage doors that don’t have least 5 feet from the oor) and away...
Page 31
Make sure the additional safety devices, such as photo eyes or edge sensors, are properly installed and adjusted (see owner’s manual). Testing and Maintaining The Garage Door Perform routine maintenance steps once a month. Review your owner’s manual for the garage door. If you don’t have a manual, look for the model number on the back of the door, or check the lock handle, hinges or other hardware for the manufacturer’s name...
Page 32
Lubrication Regularly lubricate the moving parts of the door. However, do not lubricate plastic parts such as plastic rollers and plastic idler bearing. Consult the door owner’s manual for the manufacturer’s recommendation. Door Balance Periodically test the balance of your door. •...
3055, 7033, 7035, 7053, 7055 Limited Warranty GMI Holdings, Inc. d/b/a The Genie Company (“Seller”) warrants to the original purchaser of the Models 1035, 2033, 2035, 2036, 2053, 2055, 3033, 3035, 3053, 3055, 7033, 7035, 7053 or 7055 garage door opener (“Product”), subject to all of the terms and conditions hereof, that the Product and all components thereof will be free from defects in materials and workmanship for the following period(s) of time, measured from the date of purchase: NOTE: This warranty applies only to units installed and operated within the country where purchased (USA &...
Page 34
Genie® Openers and External Receivers Manufactured between 1995 to 2011 • To erase all remote devices from all other types of Genie® openers, Press and hold the Learn Code Button until the LED stops blinking. 1. Press and hold the...
Page 35
Ouvre-portes et récepteurs extérieurs Genie® fabriqués entre 1995-2011 Pour effacer tous les dispositifs distants de tous les autres types d’ouvre- • portes Genie®, appuyez et maintenez le bouton de programmation du code 1. Appuyez sur le bouton enfoncé jusqu’à ce que la LED cesse de clignoter.