Other Function; Tv Auto On/Off Function; Attenuation To Analog Input Signal; Listening Through Headphones - Marantz SR8500 User Manual

OTHER FUNCTION

TV AUTO ON/OFF FUNCTION

This function allows the component connected to
the TV-VIDEO in jack to control the power (ON/
OFF) to the SR7500.
AUTO POWER ON
1.
Be sure the TV auto mode is ENABLED.
(Refer to page 22: PREFERENCE)
2.
Connect your TV TUNER (etc) to the TV-
VIDEO in terminal. Be sure to connect the
VIDEO input.
3.
Turn OFF the power to the TV TUNER and the
SR7500.
4.
Turn ON the TV TUNER and tune in a
receivable station.
5.
When the station is received, the SR7500
turns ON and TV is selected automatically.
AUTO POWER OFF
1.
In the above situation, turn the TV TUNER
OFF or select a channel that does not contain
any broadcast.
2.
The power to the SR7500 switches to
STANDBY after approx. 5 minutes.
Notes:
• AUTO POWER OFF is canceled if the SR7500 is
set to a source other than TV.
The function reactivates when TV is selected again.
• Some TV broadcasts may cause the TV AUTO
FUNCTION to turn ON.
• The S-Video terminal does not support "TV
AUTO ON/OFF" function.
ATTENUATION TO ANALOG INPUT
SIGNAL
LIP.SYNC
PREV MUTE
GUIDE
MENU EXIT
TEST CH.SEL SURR
1 2 3
7.1CH ATT ATT SPK-AB
4 5 5 6
DISP OSD SLEEP
7 8 9
THX
0
CLEAR MEMO
If the selected analog audio input signal is greater
than the capable level of internal processing, the
"PEAK" indicator will light up on the front display.
If this happens, you should press the ATT button
on the remote.
"ATT" indicator will be illuminated when this
function is activated. The signal-input level is
reduced by about half. Attenuation will not work
with the output signal of TAPE-OUT, CD-R/MD-
OUT, VCR1-OUT and DSS/VCR2-OUT.
This function is memorized for each individual
input source.

LISTENING THROUGH HEADPHONES

This jack may be used to listen to the SR7500's
output through a pair of headphones. Be certain
that the headphones have a standard 1/4" stereo
p h o n o p l u g . ( N o t e t h a t t h e s p e a k e r s w i l l
automatically be turned off when the headphone
jack is in use.)
AV SURROUND RECEIVER SR7500
INPUT SELECTOR
STANDBY
POWER ON/OFF PHONES
Note:
• The surround mode returns to the previous setting
as soon as the plug is removed from the jack.

DOLBY HEADPHONE MODE

This feature simulates the waveforms of the actual
sounds heard from the speakers.
When headphones are used, the MENU button
automatically switches to the Dolby headphone
mode.
The OSD that appears when the MENU button is
pressed is shown below.
HEAD PHONE
DOLBY HP MODE : BYPASS
: ✽✽✽
SURROUND
L LEVEL : 0dB
R LEVEL : 0dB
DOLDBY HP (Headphone) MODE can be selected
with the left and right cursor buttons.
BYPASS → DH1 → DH2 → DH3 → BYPASS
BYPASS : Bypasses the Dolby headphone mode
and delivers ordinary 2-channel stereo.
DH1 : The size of a typical living room space
is simulated.
DH2 : The expansiveness of a structure as
large as a music hall is simulated.
DH3 : A large space such as that found in a
movie theater is simulated.
When the PURE DIRECT mode is selected, Dolby
surround processing is bypassed and "✽✽✽" is
displayed as the mode indication.
The surround mode can be selected when any of
the modes in DH1, DH2, or DH3 is selected.
L/R LEVEL can be set in the ±10 dB range.
DISP MULTI AUTO TUNED ST SPK
SLEEP AUTO SURR DIRECT DISC 6.1
Notes:
• The surround mode returns to the previous setting
as soon as the plug is removed from the jack.
• TONE cannot be set when any of the modes in
DH1, DH2, or DH3 is selected.
• The Dolby Headphone function will not work
when 32 or 96 kHz PCM digital signals are input.

VIDEO ON/OFF

When no video signal is connected to the SR7500
or a DVD, etc., is connected directly to your TV, the
unnecessary video circuit can be turned off by
selecting the "VIDEO OFF" setting.
To select video off, press the AMP button and
press the > button until PAGE 4 is displayed. Press
the V-OFF button.
UND RECEIVER SR7500
DISP MULTI AUTO TUNED ST SPKR A B V-OFF PEAK ATT ANALOG SURROUND
DIGITAL DIGITAL
SLEEP AUTO SURR DIRECT DISC 6.1 MT X 6.1 NIGHT EQ
L C R
AAC PCM LFE
SL S SR
USE PAGE 4
ENTER
ONES
CH VOL
TUNER CD CD-R MD
TAPE AUX1 AUX2 AMP AMP
LIGHT
1 2
RC8500SR
Learning Remote Controller

DISPLAY MODE

AV SURROUND RECEIVER SR7500
LIP.SYNC
R PREV MUTE
GUIDE
MENU EXIT
DISP MULTI AUTO TUNED ST SPKR A B V-OFF PEAK ATT ANALOG SURROUND
SLEEP AUTO SURR DIRECT DISC 6.1 MT X 6.1 NIGHT EQ DIGITAL DIGITAL
L C R TEST CH.SEL SURR
LFE
AAC PCM
SL S SR
1 2 3
7.1CH ATT SPK-AB
4 5 6
DISP DISP OSD SLEEP
7 7 8 9
ENTER
THX
PHONES
0
CLEAR MEMO
You can select the display mode for the front
display of the SR7500.
To select this mode, press the DISPLAY on the
remote control or the front panel.
When this button is pressed, the display mode is
switched in the following sequence.
→ Surround Mode → Auto-display Off → Display
Off → Input Function → Surround Mode....
In Auto display off mode, the display is off. But, if
you make a change to the unit such as input or
surround mode, the display will show that change,
then go back to off after about 3 seconds. When
changing the volume, it is not displayed.
In Display off mode, the display is off completely.
Note:
• Only the DISP indicator will be illuminated on the
front display in display off condition.
M
D1
D2
D3
D4 D4
D5 D5
29