Other Function; Attenuation To Analog Input Signal; Listening Through Headphones; Video On/Off - Marantz SR4500 User Manual

OTHER FUNCTION

ATTENUATION TO ANALOG INPUT
SIGNAL
BASS TREBLE
TUNE/SEARCH
VOLUME
T-MODE RDS F.DIRECT
K ATT ANALOG SURROUND
DIGITAL DIGITAL
EQ
L C R
LFE
AAC PCM
SL S SR INPUT/DISC+ AUDIO SUB-T/ATT
DOWN UP
CH.SEL
DISPLAY MEMORY CLEAR
MUTE ATT
SYSTEM REMOTE CONTROLLER
EXIT BAND T-MODE
RC5500SR
If the selected analog audio input signal is greater
than the capable level of internal processing, the
"PEAK" indicator will light up on the front display.
If this happens, you should press the ATT button
on the front panel or on the remote.
"ATT" indicator will be illuminated when this function
is activated. The signal-input level is reduced by
about half. Attenuation will not work with the output
signal of TAPE-OUT, CD-R/MD-OUT, VCR1-OUT
and DSS/VCR2-OUT.
This function is memorized for each individual input
source.

LISTENING THROUGH HEADPHONES

This jack may be used to listen to the SR4500's
output through a pair of headphones. Be certain that
the headphones have a standard 1/4" stereo phono
plug. (Note that the speakers will automatically be
turned off when the headphone jack is in use.)
AV SURROUND RECEIVER SR4500
INPUT SELECTOR
PTY
7.1CH INPUT S. SPEAKER B
LIP.SYNC
STANDBY
POWER ON/OFF PHONES
Notes:
• When using headphones, the surround mode will
change to STEREO and TruSurround (TS)
headphones by SURROUND MODE button.
• The surround mode returns to the previous setting
as soon as the plug is removed from the jack.

VIDEO ON/OFF

When no video signal is connected to the SR4500
or a DVD, etc., is connected directly to your TV, the
unnecessary video circuit can be turned off by
selecting the "VIDEO OFF" setting.
To select video off, press the V-OFF button on
the remote.
MENU OFF
T.TONE
PURE DIRECT AUTO DTS
1 2 3
NIGHT CSII EX/ES VIRTUAL
4 5 6
DISPLAY MCH-ST STEREO 7.1CH IN
7 8 9
CLEAR MEMO A/D P.SCAN/V-OFF
0
CHANNEL/SKIP
BASS TREBLE TUNE/SEARCH
T-MODE RDS F.DIRECT
INPUT/DISC+ AUDIO SUB-T/ATT PTY
CH.SEL LIP.SYNC

DISPLAY MODE

AV SURROUND RECEIVER SR4500
R
SURROUND
DISP MULTI AUTO TUNED ST V – OFF NIGHT PEAK ATT ANALOG
DIGITAL
SLEEP AUTO SURR DIRECT DISC 6.1 MT X 6.1 EQ DIGITAL
L C R
AAC PCM LFE
SL S SR
SURROUND PURE SIMPLE
MODE DIRECT SETUP DISPLAY MEMORY
S. SPEAKER B
ENTER
AUTO HT-EQ MENU EXIT BAND
PHONES
DISP MULTI AUTO TUNED ST V – OFF NIG
SLEEP AUTO SURR DIRECT DISC 6.1 MTX 6.1
SURROUND PURE SIMPLE
MODE DIRECT SETUP
ENTER
You can select the display mode for the front display
AUTO HT-EQ MENU
of the SR4500.
To select this mode, press the DISPLAY on the front
panel or on the remote.
When this button is pressed, the display mode is
switched in the following sequence.
→ Surround Mode → Auto-display Off → Display
Off → Input Function → Surround Mode....
In Auto display off mode, the display is off. But, if
you make a change to the unit such as input or
surround mode, the display will show that change,
then go back to off after about 3 seconds. When
changing the volume, it is not displayed.
In Display off mode, the display is off completely.
Note:
• Only the DISP indicator will be illuminated on the
front display, in display off condition
SELECTING ANALOG AUDIO INPUT
OR DIGITAL AUDIO INPUT
SET UP/ MENU OFF
T.TONE
PURE DIRECT AUTO DTS
SET UP/
1 2 3
T.TONE
NIGHT CSII EX/ES VIRTUAL PURE DIRECT AUTO
4 5 6 1
DISPLAY MCH-ST STEREO 7.1CH IN
NIGHT CSII
7 8 9 4
CLEAR MEMO A/D P.SCAN/V-OFF DISPLAY MCH-ST
0 7
CHANNEL/SKIP CLEAR MEMO
BASS TREBLE TUNE/SEARCH
BASS TREBLE
T-MODE RDS F.DIRECT
T-MODE
If you have already assigned the digital inputs, you
can temporarily select the audio input mode for
each input source with the A/D button on the remote
controller.
When this button is pressed, the input mode is
switched in the following sequence.
→ Digital Auto → Digital → Analog → Digital Auto....
In Digital Auto mode, the types of signals being
input to the digital and analog input jacks for the
selected input source are detected automatically.
If no digital signal is being input, the analog input
jacks are selected automatically.
In Digital mode, input is fixed to an assigned digital
input terminal.
In analog mode, the analog input jacks are selected.
This selecting is temporary, so the result will not be
stored in memory.
If you need to change the input mode completely,
use INPUT setup in SETUP MENU system. (see
page 17)
MENU OFF
DTS
2 3
EX/ES VIRTUAL
5 6
STEREO 7.1CH IN
8 9
A/D P.SCAN/V-OFF
0
CHANNEL/SKIP
TUNE/SEARCH
RDS F.DIRECT
27