Selecting Analog Audio Input Or; Digital Audio Input; Recording An Analog Source; Ht-Eq - Marantz SR4001 User Manual

SELECTING ANALOG AUDIO INPUT OR

DIGITAL AUDIO INPUT

TV DVD VCR DSS
TUNER CD CDR MD
TAPE AUX1 AUX2 AMP AMP
REMOTE CONTROLLER
RC5001SR
4 5 6
M-CH ST STEREO NIGHT P.SCAN
7 8 9
7.1CH IN A/D A/D

HT-EQ

0 +10 +10
CL MEMO
CH/ CAT VOLUME
SPKR A/B MUTE
MULTI/ CAT M-SPKR
If you have already assigned the digital inputs, you
can temporarily select the audio input mode for each
input source as following procedures.
Press the AMP button and press the A/D (0) button.
When this button is pressed, the input mode is
switched in the following sequence.
→ HDMI Auto → HDMI → Digital Auto → Digital →
Analog → HDMI Auto....
In HDMI Auto mode, the types of signals being input
to the digital and analog input jacks for the selected
input source are detected automatically.
If no digital signal is being input, the analog input
jacks are selected automatically.
In Digital and HDMI mode, input is fixed to an
assigned digital input terminal.
In analog mode, the analog input jacks are selected.
This selecting is temporary, so the result will not be
stored in memory.
If you need to change the input mode completely, use
INPUT SETUP in OSD menu system. (see page 26)

RECORDING AN ANALOG SOURCE

In normal operation, the audio or video source
selected for listening through the SR4001/SR5001 is
sent to the record outputs.
This means that any program you are watching
or listening to may be recorded simply by placing
machines connected to the outputs for TAPE OUT,
CD-R/MD OUT, VCR1 OUT in the record mode.
To record the input source signal you are currently
watching or listening to
1.
- PRESET + - TUNING
AV SURROUND RECEIVER SR5001
INPUT SELECTOR
DISC+ ANGLE SUB TITLE
CH-SEL V-OFF ATT.
BASS
1.
TV TV DVD DVD VCR VCR
SURROUND PURE SIMPLE
MULTI MODE DIRECT SETUP TUNER TUNER CD CD CDR CDR
MULTI SPEAKER
STANDBY TAPE AUX1 AUX2
AUTO HT-EQ MENU
POWER ON/STANDBY PHONES
REMOTE CONTROLLER
RC5001SR
1.
Select the input source to record by turning the
INPUT SOURCE knob on the front panel or
simply press the input selector buttons on the
remote.
The input source is now selected and you may
watch or listen to it as desired.
2.
The currently selected input source signal
is output to the TAPE OUT, CD-R/MD OUT,
VCR1 OUT outputs for recording.
3.
Start recording to the recording component as
desired.
Recording the video from one source and
the audio from another
You can add the sound from one source to the
video of another source to make your own video
recordings.
Below is an example of recording the sound from
a compact disc player connected to CD IN and the
video from a video camera connected to DSS/VCR2
to video cassette recorder connected to the VCR1
OUT jack.
DISC+ ANGLE SUB TITLE AUDIO
1.
CH-SEL V-OFF ATT.
BASS TREBLE
TV DVD VCR VCR DSS
2.
TUNER CD CD CDR MD
TAPE AUX1 AUX2 AMP
REMOTE CONTROLLER
RC5001SR
1.
Switch the video output source to VCR1 by
simply pressing the input selector buttons on
the remote.
2.
Switch the audio input source to CD by simply
pressing the input selector buttons on the
remote.
3.
Now "CD" has been selected as the audio input
source and "VCR1" as the video input source.
Notes:
• If you change the input source during recording, you
will record the signals from the newly selected input
source.
• You cannot record the surround effects.
+
• Digital input signals are only output to the digital
outputs. There is no conversion from digital to
AUDIO
analog.
TREBLE
DSS DSS When connecting CD players and other digital
MD MD components, do not connect only the digital
AMP
terminals, but the analog ones as well.
HT-EQ
AV SURROUND RECEIVER SR5001
INPUT SELECTOR
SURROUND PURE SIMPLE
MULTI MODE DIRECT SETUP DISPLAY MEMORY
MULTI SPEAKER
STANDBY ENTER
AUTO HT-EQ MENU EXIT
POWER ON/STANDBY PHONES
Press the HT-EQ button on the front panel to turn on
the HT-EQ mode.
The tonal balance of a film soundtrack will be
excessively bright and harsh when played back over
audio equipment in the home. This is because fi lm
soundtracks were designed to be played back in
large movie theater environments.
Activating the HT-EQ feature when watching a fi lm
made for movie theaters corrects this and restores
the correct tonal balance.
The HT-EQ feature is available except in the following
modes.

• 7.1 CH INPUT

• PURE-DIRECT
• When VIRTUAL is set for the surround mode
7.1 CH INPUT
The SR4001/SR5001 is equipped for future
expansion through the use of Multi channel Super
Audio CD multichannel player or DVD-Audio player.
When this is selected, the input signals connected to
the L(front left), R (front right), CENTER, SL (surround
left), SR (surround right) and SBL (surround back left)
and SBR (surround back right) channels of the 7.1
CH. In jacks are output directly to the front (left and
right), center, surround (left and right) and surround
back speaker systems as well as the pre-out jacks
without passing through the surround circuitry.
In addition, the signal input to the SW (subwoofer)
jack is output to the PRE OUT SW (subwoofer) jack.
When 7.1 CH. INPUT is selected, the last video input
used remains routed to the Monitor Outputs.
This permits simultaneous viewing with video
sources.
2. 1.
AV SURROUND RECEIVER SR5001
INPUT SELECTOR
SURROUND PURE
MULTI MODE DIRECT
MULTI SPEAKER
VOLUME
STANDBY
AUTO HT-EQ
POWER ON/STANDBY PHONES
DOWN
CLEAR
MUTE
4.
BAND T-MODE
AUX 1 INPUT
DIGITAL S-VIDEO VIDEO L
VOLUME
DOWN UP
MEMORY CLEAR
MUTE ATT
BAND T-MODE
AUX 1 INPUT
DIGITAL S-VIDEO VIDEO L AUDIO R
M-CH ST STEREO NIGHT P.SCAN
7 8 9
2.
7.1CH IN 7.1CH IN A/D HT-EQ
0 0 +10
CL MEMO
CH/ CAT VOLUME VOLUME
SPKR A/B MUTE
4.
MULTI/ CAT M-SPKR
INFO MENU
ENTER
T.TONE
/SET UP EXIT
REC T.DISP PTY F.DIRECT
- + - +
PRESET TUNING
DISC+ ANGLE SUB TITLE AUDIO
CH-SEL V-OFF ATT.
1.
BASS TREBLE
TV TV DVD DVD VCR VCR DSS DSS
TUNER CD CDR MD
TAPE AUX1 AUX2 AMP
REMOTE CONTROLLER
RC5001SR
37