Marantz SR4001 User Manual page 43

CLEARING STORED PRESET STATIONS
You can remove preset stations from the memory
using the following procedure.
2. 3.
AUTO
1
CS
2. 4
VOLUME
M-CH ST
7
DOWN CL CL
CH/ CAT
3.
DISPLAY MEMORY CLEAR
MUTE
ENTER
EXIT BAND T-MODE AUX 1 INPUT
DIGITAL S-VIDEO VIDEO
INFO
1.
Recall the preset number to be cleared with
the method described in "Recalling" a preset
station.
2.
Press the MEMO button on the front panel or
press the MEMO button on the remote.
3.
The stored preset number blinks in the display
for 5 seconds. While blinking, press the CLEAR
button on the front panel or the remote.
4.
"xx CLEAR" appears on the display to indicate
that the specified preset number has been
cleared.
Note:
To clear all stored preset stations, press and hold the
CLEAR and the ENTER buttons for two seconds.
40
SORTING PRESET STATIONS
AV SURROUND RECEIVER SR5001
INPUT SELECTOR
LIP SYNC/
dts INPUT
2 3
SURROUND PURE SIMPLE
MULTI MODE DIRECT SETUP DISPLAY
EX/ES VIRTUAL T.MODE
MULTI SPEAKER
5 6
STANDBY ENTER
AUTO HT-EQ MENU EXIT
STEREO NIGHT P.SCAN
POWER ON/STANDBY PHONES
8 9
7.1CH IN A/D HT-EQ
0 +10
MEMO MEMO
VOLUME
SPKR A/B MUTE
If you have stations memorized, and there is a gap in
MULTI/ CAT M-SPKR
the sequential order:
MENU
I.e. the stations are stored as follows
1) 87.1 MHz
2) 93.1 MHz
3) 94.7 MHz
10) 105.9 MHz
(notice there is no stations programmed for pre sets
for 4-9), you can have pre set 10 become pre set 5:
To sort the numbers, press and hold the MEMO and
the 4 cursor buttons.
"PRESET SORT" will appear on the display and
sorting will be done.
NAME INPUT OF THE PRESET STATION.
This function allows the name of each preset channel
to be entered using alphanumeric characters.
VOLUME
Before name inputting, you need to store preset
DOWN UP stations with the preset memory operation.
MEMORY CLEAR
MUTE ATT
4.
BAND T-MODE AUX 1 INPUT
DIGITAL S-VIDEO VIDEO L AUDIO R
AV SURROUND RECEIVER SR5001
INPUT SELECTOR
SURROUND PURE SIMPLE
MULTI MODE DIRECT SETUP
MULTI SPEAKER
STANDBY
AUTO HT-EQ MENU
POWER ON/OFF PHONES
2. 5. 6.
5.
4.
1.
Recall the preset number to be inputted name
with the method described in "Recalling" a
preset station.
2.
Press the MEMO button on the front panel or
press the MEMO button on the remote for more
than 3 seconds.
3.
The left most column of the station name
indicator fl ashes, indicating the character entry
ready status.
4. When you press the 3 or 4 cursor buttons on
the front panel or the 5 / 6 buttons on the
remote, alphabetic and numeric characters will
be displayed in the following order:
A → B → C ... Z → 1 → 2 → 3 ..... 0 → – → +
→ / → (Blank) → A
← DOWN
5.
After selecting the fi rst character to be entered,
press the MEMO or ENTER buttons, press the
MEMO button on the remote.
The entry in this column is fi xed and the next
column starts to fl ash. Fill the next column the
same way.
5. 2. 5. 6.
To move back and forth between the characters,
press the 1 / 2 cursor buttons or press S or
VOLUME
T buttons on the remote.
DOWN UP Note:
Unused columns should be fi lled by entering blanks.
DISPLAY MEMORY CLEAR
MUTE ATT
ENTER
EXIT BAND T-MODE AUX 1 INPUT
DIGITAL S-VIDEO VIDEO L AUDIO R
6.
To save the name, press the MEMO button
on the front panel or remote for more than 2
seconds.
7 8 9
7.1CH IN A/D HT-EQ
Ten keypad
0 +10
CL MEMO MEMO
CH/ CH/ CAT CAT VOLUME
SPKR A/B MUTE 1
2
MULTI/ CAT M-SPKR
3
INFO MENU
4
ENTER ENTER
5
T.TONE
/SET UP EXIT
6
REC T.DISP PTY F.DIRECT
7
- PRESET + - - TUNING TUNING + +
8
9
DISC+ ANGLE SUB TITLE AUDIO
CH-SEL V-OFF ATT.
0
BASS TREBLE
TV DVD VCR DSS
UP →
Press, press again, press again, etc.
A → B → C → 1 → A
D → E → F → 2 → D
G → H → I → 3 → G
J → K → L → 4 → J
M → N → O → 5 → M
P → Q → R → 6 → P
→ → → →
S T U 7 S
→ → → →
V W X 8 V
Y → Z → space → 9 → Y
– → + → / → 0