Display; Osd/Blanking - Marantz VP-11S1 User Manual

Display

Standard 1
Fine Menu 1 Keystone
0
Fine Menu 2 Scale 0
Input Signal
Width 0
RGB/HD Adjust Position H 0
Display Position V
0

OSD/Blanking

Overscan Enable
Config. Installation
Front
– Keystone
Adjust trapezoid image to rectangle image.
– Scale
Reduces the image without changing the aspect ratio. The image can be reduced to about 70% the
original size.
– Width
Reduces the image width without changing the image height. The width can be reduced to about 75%
the original size.
– Position H, V
Adjust the position of the input signal. H adjusts the horizontal position of the input signal. V adjusts the
vertical position of the input signal.
– Overscan
Selects whether to show or hide picture borders with NTSC, PAL, SECAM, 480i, 480p, 576i and 576p
signals.
Enable: Does not display borders of image signals. (Normally, use this mode.)
Disable: Displays the entire image signal.
– Instllation
Sets the installation mode of the projector.
Front: Select to set the projector on a tabletop and project from in front of the screen.
Rear: Select to set the projector on a tabletop and project from behind the screen.
F + Ceiling: Select to mount the projector on the ceiling and project from in front of the screen.
R + Ceiling: Select to mount the projector on the ceiling and project from behind the screen.
26
Item Adjustments
Keystone
-25 0 25
(Electronic vertical
( ) ( ) ( )
keystone correction)
Scale -100 0
(Min) (Max)
-100 0
Width
(Min) (Max)
Position H -50 0 50
(Left) (Default) (Right)
-50 0 50
Position V
(Down) (Default) (Up)
Overscan
Enable, Disable
Installation Front, Rear, F+Ceiling,
R+Ceiling
OSD/Blanking
Standard 1
Picture Adjust Menu Position
Fine Menu 1 Language
Fine Menu 2 Status Info.
Input Signal Power-OFF Confirm.
RGB/HD Adjust Blanking Memory
Display Blanking Top
OSD/Blanking Blanking Bottom
Config. Blanking Left
Blanking Right
Item
Menu Position Top-L, Top, Top-R, Center-L, Center, Center-R,
Bottom-L, Bottom, Bottom-R
Language English, Deutsch, Français, Español,
Português, Italiano
Enable, Disable
Status Info.
Power-OFF Confirm. Enable, Disable
Off, Memory 1, Memory 2, Memory 3
Blanking Memory
Blanking Top
Blanking Bottom
Blanking Left
Blanking Right
– Menu Position
OSD position is selected from 9 positions.
– Status Info.
Enable: Displays the current status of the projector for a set amount of time in the upper right-hand
corner of the screen at startup and whenever the Input Source, Picture Mode, Aspect ratio or
other setting is changed.
Disable: Does not display Status Info.
– Power-OFF Confirm.
Disable: Directly puts the projector on standby without displaying the confirmation message when power
is shut off from the button on the remote controller or the
Enable: Displays a confirmation message asking whether to shut the power off or continue use
when power is shut off from the
projector. To shut off the power immediately, select "Yes" and press the ENTER button. To
not shut off the power, select "No" and press the ENTER button.
– Blanking Memory
Sets the blanking mode with which part of the screen can be hidden in black bands. To use this mode
or change the setting, select from Memory 1 to 3.
Off: Turns the blanking mode off. No masking occurs.
Memory 1-3: Memorize the blanking width of the top, bottom, left and right masks set with the
below features. Up to three settings can be memorized.
– Blanking Top, Bottom, Left and Right
Set the blanking width of the top, bottom, left and right masks, which are then memorized in Memory 1
– 3 of Blanking Memory. Each can be set from 0 (no mask) to a maximum 100.
Top-L
English
Enable
Enable
Memory 1
0
0
0
0
Adjustments
0 100
0 100
0 100
0 100
/I button on the projector.
button on the remote controller or the /I button on the