Sharp Aquos LC-45GD6U Operation Manual page 23

Watching TV
Please note: your new AQUOS Liquid Crystal Television is capable of receiving the full range of cable-TV channels available
today, from the most advanced digital and HDTV channels, to the more traditional analog channels. As the transition toward
full digital TV continues, some cable-TV systems in the USA will have a mixture of analog and digital channels in their
lineups. When you are viewing analog cable-TV channels and wish to switch to viewing digital cable-TV channels, you must
press the DIGITAL button (located just below the numbers) on the remote control first. In similar fashion, when you are
viewing digital channels and wish to switch to viewing analog channels, you must press either the ANALOG-A or ANALOG-
B button (depending on whether you have your cable connected to the A or B terminal) on the remote first.
You can change channels in several ways.
lii~L{:
• While watching a broadcast, press A-ANALOG-B to view
the image received from the other tuner.
You can change channels in several ways.
As well as the methods outlined below, you can also select
programs using the Channel List. (See page 86.)
• FLASHBACK will not work if no channel has been
changed after TV is turned on.
tl V~ ~~
CARD ,. MUTE
0 - 0
lXIVirtuPJ
@ffi®
MENU
O~o
I I
_e_
_
..
•••
_
..
A-~OG'B DIGITAL INPUT
0 0 . 0
• Digital - Air (Two-part Number)
Method 1
When you press CH/\fVor FLASHBACK, repeat the
same steps for Analog-TV.
Method 2
Using remote control buttons (0-9, •
(DOT) and
ENTER) to select the channels including a decimal
point.
To select a 4-digit channel number
(e. g., Channel 22.1):
Press 2
~2~.(DOT) ~1~
ENTER
• While watching a broadcast, press DIGITAL.
CARD
'ftJ
\.eH MUTE
oU··
0
lXIVirtuaJ
@§J§@>
MENU
O~o
I I
EO~ORN
•••
•••
--- ._-
•
~.
DIOLICr
Method 3
Using remote control buttons (0-9
and ENTER) to select
up to 125 channels for VHF/UHF/CATV.
To select a 1 or 2-digit channel number
(e. g., Channel 5):
Press 5~
ENTER
Method 1
Using CH/\fV on the remote control unit or on the
display.
Method 2
1. Press FLASHBACK to switch to the previously tuned
channel.
2. Press FLASHBACK again to switch back to the
currently tuned channel.
• Complete the above steps within a few seconds.
• When you enter 0-9 and .(DOT), channel selection will
be made if there is no operation for a few seconds .
• When selecting a 1-digit channel number, it is not
necessary to press 0 before the number.
• When you enter 0-9 only, channel selection will be made
if there is no operation for a few seconds.
• • (DOT) can be used instead of ENTER.
To select a 3-digit channel number
(e. g., Channel 115):
Press
1~1~5
• Digital - Cable (One-part Number)
Method 1
When you press CH/\fVor FLASHBACK, repeat the
same steps for Analog-TV.
Method 2
Using remote control buttons (0-9
and ENTER) to select
the channels including a decimal point.
To select a 3-digit channel number
(e. g., Channel 310):
Press
3~
1
~O~ENTER
@-22
• When you enter 0-9 only, channel selection will be made
if there is no operation for a few seconds.
• If you push "O" by itself, nothing will happen.
• When you enter 0-9 only, channel selection will be made
if there is no operation for a few seconds.