Maintenance - Toro Workman MD Operator's Manual

Operating on Rough Terrain
WARNING
Sudden changes in terrain may cause abrupt
steering wheel movement, possibly resulting in
hand and arm injuries.
• Reduce your speed when operating on rough
terrain and near curbs.
• Grip the steering wheel loosely around the
perimeter keeping thumbs up and out of the way
of the steering wheel spokes.
Reduce the ground speed of the machine and load carried in
the machine when operating on rough terrain, uneven ground,
and near curbs, holes, and other sudden changes in terrain.
Loads may shift, causing the machine to become unstable.
If you will be using the machine on rough terrain, you can
install the optional ROPS Kit.
Loading and Dumping
WARNING
The weight of the box may be heavy. Hands or
other body parts could be crushed.
• Keep hands and other body parts clear when
lowering the box.
• Do not dump materials on bystanders.
•
Do not exceed the rated weight capacity of the machine
when operating it with a load in the cargo box, when
towing a trailer, or both; refer to
•
Use caution when operating the machine on a hillside or
on rough terrain, particularly with a load in the cargo box
or when towing a trailer or both.
•
Use caution when carrying tall loads in the cargo box.
•
Be aware that the stability and control of the machine
are reduced when the load in the cargo box is poorly
distributed.
•
Carrying oversized loads in the cargo box changes the
stability of the machine.
•
The steering, braking , and stability of the machine are
affected when carrying a load where the weight of the
material cannot be bound to the machine such as the
liquid in a large tank.
•
Never dump a loaded cargo box while the machine is
sideways on a hill. The change in weight distribution may
cause the machine to overturn.
•
When operating with a heavy load in the cargo box,
reduce your speed and allow for sufficient braking
distance. Do not suddenly apply the brakes. Use extra
caution on slopes.
Specifications (page 16).
•
Be aware that heavy loads increase your stopping distance
and reduce your ability to turn quickly without tipping
over.
•
The rear cargo space is intended for load carrying
purposes only, not for passengers.
•
Never overload your machine. The name plate (located
under the middle of the dash) shows the load limits for
the machine. Never overfill attachments or exceed the
machine maximum gross machine weight (GVW); refer
to Loading the Cargo Box (page

Maintenance

•
Before servicing or making adjustments to the machine,
move the machine to a level surface, stop the engine, set
the parking brake, and remove the key from On/Off
switch to prevent accidental starting of the engine.
•
Never work under a raised bed without placing the
bed-safety support onto the fully extended bed-actuator
rod.
•
Make sure all hydraulic fittings are tight, and all hydraulic
hoses and lines are in good condition before applying
pressure to the system.
•
Keep your body and hands away from pin hole leaks or
nozzles that eject hydraulic fluid under high pressure.
Use paper or cardboard, not your hands, to search
for leaks. Hydraulic fluid escaping under pressure can
have sufficient force to penetrate skin and cause serious
damage to your body. If fluid is injected into the skin, it
must be surgically removed within a few hours by a doctor
familiar with this form of injury, or gangrene may result.
•
Before disconnecting or performing any work on the
hydraulic system, all pressure in the hydraulic system
must be relieved by stopping the engine and cycling the
hydraulic control valve for the bed lift from raise to lower
and/or lowering box and attachments. If equipped,
place the remote-hydraulics lever in the float position.
If the box must be in raised position, secure it with the
bed-safety support.
•
To make sure the entire machine is in good condition,
keep all nuts, bolts, and screws properly tightened.
•
To reduce the potential fire hazard, keep the engine area
free of excessive grease, grass, leaves, and accumulation
of dirt.
•
If the engine must be running to perform a maintenance
adjustment, keep hands, feet, clothing, and any parts of
the body away from the engine and any moving parts.
Keep everyone away.
•
Do not overspeed the engine by changing the governor
settings. The maximum engine speed is 3650 rpm. To
ensure safety and accuracy, have an Authorized Toro
Distributor check the maximum engine speed with a
tachometer.
7
23).