Montigo P52DF Installation & Maintenance Manual
  1. Manuals
  2. Brands
  3. Montigo Manuals
  4. Indoor Fireplace
  5. P52DF
  6. Installation & maintenance manual

Montigo P52DF Installation & Maintenance Manual

P series residential fireplace
Hide thumbs Also See for P52DF:
Table of Contents

Advertisement

Quick Links

See also: Installation , Installation and Maintenance Manual
Installation & Maintenance Manual
DANGER
Read and understand this manual. Improper installation, adjustment, alteration,
service or maintenance can cause serious injury, property damage or even death.
For assistance or additional information consult a qualified installer, service
agency or the gas supplier.
Glass doors on gas fireplaces are extremely hot while the fireplace is on and
remain hot even after the fireplace has been turned off. Safety screens are
available and can reduce the risks of severe burns. Please keep children away
from the fireplace at all times.
XG0196
CAUTION
Canadian Heating Products Inc. Langley, BC V4W 4A1 | Montigo Del Ray Corp. Ferndale, WA 98248
P52DF Indoor
P Series
Residential
Fireplace
WARNING
Do not store or use gasoline or any other flammable vapors and liquids in the vicinity of
this or any other gas burning appliance. A fire or explosion my occur causing serious
injury, property damage or even death.
NOTICE
Installer: Leave this manual with the appliance. Do not remove.
Consumer: Retain this manual for maintenance and future reference. Do not Discard.
DANGER
Blank
IF YOU SMELL GAS
Blank
Flammable materials
Explosion risk
Toxic
Corrosive
Danger overhead crane
Fork lift trucks
High voltage
Do not try to light any appliance.
Blank
Flammable materials
Explosion risk
Toxic
Corrosive
Danger overhead crane
Fork lift trucks
High voltage
Do not touch any electrical switch; do not use any phone in your building.
General Warning
Laser Radiation
Biohazard
Oxidising
Hot surface
Danger of entrapment
Danger of death
Flammable materials
Explosion risk
Immediately call your gas supplier from a neighbor's phone. Follow the gas
Toxic
Corrosive
Danger overhead crane
Fork lift trucks
High voltage
General Warning
Laser Radiation
Biohazard
Oxidising
Hot surface
Danger of entrapment
Danger of death
Irritant
Slippery floor
Watch your step
Cutting
High temperatures
Glass hazard
Danger of suffocation
Blank
supplier's instructions.
Hot surface
Danger of entrapment
Danger of death
General Warning
Laser Radiation
Biohazard
Oxidising
Irritant
Slippery floor
Watch your step
Cutting
High temperatures
Glass hazard
Danger of suffocation
Gas bottles
Watch for
Electricity
Danger for cutter
Entrapment hazard
Battery hazard
Rotating parts
Flammable materials
Explosion risk
falling objects
Toxic
Corrosive
Danger overhead crane
Fork lift trucks
High voltage
If you cannot reach your gas supplier, call the fire department.
Irritant
Slippery floor
Watch your step
Cutting
High temperatures
Glass hazard
Danger of suffocation
Gas bottles
Watch for
Electricity
Danger for cutter
Entrapment hazard
Battery hazard
Rotating parts
Low temperature
Strong magnetic field
falling objects
Optical radiation
Non ionizing
Radiation
Hazardous to the
Danger of harming
radiation
Environment
your hands
General Warning
Laser Radiation
Biohazard
Oxidising
Hot surface
Danger of entrapment
Danger of death
Gas bottles
Watch for
Electricity
Danger for cutter
Entrapment hazard
Battery hazard
Rotating parts
Low temperature
Strong magnetic field
falling objects
Optical radiation
Non ionizing
Radiation
Hazardous to the
Danger of harming
radiation
Environment
your hands
Irritant
Slippery floor
Watch your step
Cutting
High temperatures
Glass hazard
Danger of suffocation
Low temperature
Strong magnetic field
Optical radiation
Non ionizing
Radiation
Hazardous to the
Danger of harming
radiation
Environment
your hands
Gas bottles
Watch for
Electricity
Danger for cutter
Entrapment hazard
Battery hazard
Rotating parts
falling objects
C
®
US
150204.3

Advertisement

Table of Contents
loading

Related Manuals for Montigo P52DF

Summary of Contents for Montigo P52DF

  • Page 1 Danger of harming radiation Environment your hands Gas bottles Watch for Electricity Danger for cutter Entrapment hazard Battery hazard Rotating parts falling objects ® XG0196 150204.3 Canadian Heating Products Inc. Langley, BC V4W 4A1 | Montigo Del Ray Corp. Ferndale, WA 98248...

  • Page 2: Table Of Contents

    P52DF* Indoor Gas Fireplace NOTICE You must read and understand this manual prior to installation, operation or troubleshooting this appliance. Please retain this owner’s manual for future reference and maintenance. Table of Contents Instruction Manual Contents Section 7: Screen Installation and Removal Section 8: Installing &...

  • Page 3: Safety Alerts

    Introduction Congratulations on your purchase of a Montigo Fireplace. With over 30 years of experience, Montigo is committed to providing you with a gas fireplace that is not only a beautiful addition to your space, but that is also designed and manufactured to the highest safety, reliability and engineering standards.

  • Page 4: Section A: Before You Start

    IMPORTANT MESSAGE: SAVE THESE INSTRUCTIONS Determine the desired install location of your fireplace. „ The P Series P52DF* Direct Vent fireplace must be installed See Section 1, Dimensions on Page 5, and refer to „ in accordance with these Instructions. Carefully read all the Framing Section 2 for details.

  • Page 5: Rating Plate Sample

    P52DF* Indoor Gas Fireplace Installation Rating Plate Sample Figure A: Rating Plate for IPI eletronic ignition Page 5 XG0196 - 150204.3...

  • Page 6: Section 1: Installation Overview And Product Dimensions

    Select a location that does not interfere The P52DF* fireplace may be installed in any location with room traffic, has adequate ventilation and offers an that maintains proper clearances to air conditioning ducts, accessible path for Direct Vent installation.

  • Page 7: Section 2: Framing & Clearances

    P52DF* Indoor Gas Fireplace Installation Section 2: Framing & Clearances 20” Max Frame in the enclosure for the unit with framing materials. The framed opening for the assembled fireplace is 52" wide, Combustible Header x 43" high x 24 1/2" deep, see Figure 2 Heat Sheild 26”...

  • Page 8: Clearances

    Clearance to the insulated flange is 1". 4" Installing The Standoffs To avoid elevated mantel temperatures, all P52DF* gas Figure 6d. Securing the Nailing Flange Extension. fireplaces are required to have the supplied standoffs installed. The supplied nailing extension must be placed along the top The fireplace is supplied with two standoffs.

  • Page 9: Section 3: Venting

    UNIT ONLY) Converting to Rear Vent Section 3-1: Use the following instructions to convert a P52DF* from Use the following instructions to convert a P52DF* for 5"/ 10" to 5"/ 8" venting for Top or Rear Vent use Rear Vent use: outside of 8 feet vertically from the unit: 1.

  • Page 10: Section 3-2: Installing A Roof Mounted Direct Vent Termination (Pvtk-1) For 5"/8

    P52DF* Indoor Gas Fireplace Installation Section 3-2: Installing a Roof Mounted Direct Vent Termination (PVTK-1) for 5"/8" PVTK1 Termination This section applies to installations where the direct vent termination 2’ min. will be roof mounted. Section 3-2-1: Venting Layout Support ring 8’...
  • Page 11 P52DF* Indoor Gas Fireplace Installation PVTK1 Termination PEXT Sections 8’ min. Support plate 32’ max Support ring 12” Max. Figure 8c. (5"/8") Rear vent, Roof mounted venting (1 = 90° bend). Note: Images are shown without screens for clarity purposes. However, your fireplace should not be operated without proper installation of screens.

  • Page 12: Installing A Wall Mounted Direct Vent

    P52DF* Indoor Gas Fireplace Installation Installing a Wall Mounted Direct Section 3-3-1: Installing a Wall Mounted Direct Section 3-3: Vent Termination (5"/8") Vent Termination (5"/10") This section applies to installations where the direct vent This section applies to installations where the direct vent termination will be wall mounted with 5"...

  • Page 13: Section 3-3-2: Venting Layout

    If your installation does not fall Notes Wall Mounted Terminations: 5"/8" TOP VENT within the venting graph parame- ters, please contact a local Montigo All measurements for vertical or horizontal runs are „ Dealer for Power Venting options.
  • Page 14 The vent run must comply with the Venting Graph for Rear vent, wall mounted terminations, Figure 12. Note: If power venting, vent run must be reduced to 5"/8" or 4"/7". contact your Montigo dealer to discuss power venting options. 56”...
  • Page 15 P52DF* Indoor Gas Fireplace Installation 45° Corner Installation. 45° or less Corner Installation. Attach an REL-45 (45° elbow) directly onto the flue collar. Use an RTO-4 termination and an RFL-4 (48" compressed Cut the RXT-20 to suit, and attach it to the REL-45. Slide length) and a frame, if appropriate.

  • Page 16: Section 3-4: Venting Components

    REXT - 6 (72" f/m Section) and avoid any possible hot spots. E - Elbows PEL-90MM (m/m 90º Elbow) Montigo recommends the use of a flex section for the „ PEL-90FF ( f/f 90º Elbow) final pipe connected directly to the fireplace offering PEL-90FM ( f/m 90º...

  • Page 17: Section 3-5: Heat Shields

    P52DF* Indoor Gas Fireplace Installation Section 3-5: Heat Shields Installing a Wall Mounted RHS 104 Heat shield. The RHS104 Heat shield MUST be used in conjunction with the RTO-4 Termination (Figure 16 and 16a). Installing a Wall Mounted RHS 102 Heat shield...

  • Page 18: Section 4: Wiring

    WHITE ON/OFF BLACK CONTROL Figure 17. Wiring Diagram for P52DF with SIT Proflame 2 Electronic Ignition Installations in Canada must be electrically grounded in accordance with CSA C22.1 Canadian Electrical Code Part 1 and/or Local Codes. Installations in the USA must be grounded in accordance 5½”...

  • Page 19: Section 5: Installing The Gas Line

    ■ Verify that your fireplace is compatible with your available gas type. (Natural Gas or Propane shown by "N" or "L" in your model number ■ If gas type is not compatible, contact your local Montigo representative. 1¼” ■ Conversion kits must be installed by a qualified service technician.

  • Page 20: Section 6: Finishing

    P52DF* Indoor Gas Fireplace Installation Section 6: Finishing Mantels & Surrounds Finishing Around the Fireplace NOTE: National Canadian Gas Association mantel test Non-combustible mantels and mouldings may be safely requirements are for fire hazard prevention to combustible installed over the top and on the front of the fireplace materials.

  • Page 21: Section 7: Screen Installation And Removal

    P52DF* Indoor Gas Fireplace Installation Section 7: Screen Installation and Removal Left Side Detail Upper Screen Studs Upper Screen Removing / Attaching Screens: Stud Catch To R To Remove Screens: Grasp each top outer corner of the screen with your thumb and finger and pull towards yourself.

  • Page 22: Section 8: Installing & Removing The Door

    P52DF* Indoor Gas Fireplace Installation Section 8: Installing & Removing the Door Removing the door: The P52DF* doors are removed in a few simple steps. Step 3: Release the Door Buckles Follow these below to remove the Horizontal access panel, unlatch the door buckles and, remove the door.

  • Page 23: Section 9: Installing The Accessories

    Installing the Firestones or optional Fireglass Step 8: Removing the Door: The P52DF* is supplied with firestones. Optional Grasp the Door on either side, usually midway and fireglass may be purchased from the factory. Remove lift upward, lift the door carefully up and away from the Door as shown in the previous Instruction.

  • Page 24: Installing Optional Speckled Stones

    P52DF* Indoor Gas Fireplace Installation Installing Optional Speckled Stones [RR300SS + RR50SS] Once the glass door has been removed as shown in the previous section, place the speckled stones evenly across the pan and burner. Ensure stones do not overlap too much as this will effect the flame pattern, see figure 24.

  • Page 25: Installing The Driftwood Log Set

    P52DF* Indoor Gas Fireplace Installation Installing the Driftwood Log Set The P52DF* has the option of installing a drift wood log set. Once the firestones or speckled stones have been installed the log set can be installed. Ensure logs are securely placed and will not tip or fall.
  • Page 26 P52DF* Indoor Gas Fireplace Installation Step 7. Place log 5 from LGS59 in the back left corner Step 10. Place log 6 of LGS58 across log 4 from of the burner, behind the pilot. Place Log 4 from LGS58 LGS58 and log 4 from LGS59, see figure 25j.

  • Page 27: Operation

    P52DF* Indoor Gas Fireplace Operation Operation For Your Safety - READ BEFORE LIGHTING: with American Flame Electronic Ignition WARNING If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury or death.

  • Page 28: Maintenance

    P52DF* Indoor Gas Fireplace Maintenance Cleaning Maintenance When the fireplace is first activated, there may be some smoke and a visible film may be left on the glass. This is a normal condition, and is the result of burning of protective General coatings on new metal.

  • Page 29: Replacing Light Bulbs

    P52DF* Indoor Gas Fireplace Maintenance Troubleshooting: Replacing Light Bulbs The P52DF* light bulbs can be replaced in a few simple SIT Proflame 2: steps. Follow the directions for removing the door on page The following is a troubleshooting chart of possible problems: 20.

  • Page 30: Replacement Parts

    If your fireplace still does not operate correctly, consult your local Montigo dealer. All service and repairs should be performed by a qualified Technician. All spare parts, optional fans, and optional trim finishes are available from your local Montigo dealer. Page 30...

  • Page 31: Appendix A: Venting Terminations

    P52DF* Indoor Gas Fireplace Appendix Appendix A: Venting Terminations Location Canada* USA** 12 inches 12 inches clearance to the termination frame above grade, veranda, porch, deck, or balcony 12 inches 12 inches clearance to top of doors or operable windows...

  • Page 32: Appendix B: Warranty

    The duration of any implied warranty with respect to this Montigo Gas Appliance is limited to the duration of the foregoing warranty. Some states do not allow limitation on how long an implied warranty lasts, so the above may not apply to you.

  • Page 33: Appendix C: State Of Massachusetts

    P52DF* Indoor Gas Fireplace Appendix Appendix C: State of Massachusetts Amendment (Gas Fireplace / Equipment sold in the State of Massachusetts) 5.08: Modifications to NFPA-54, Chapter 10 (1) Revise NFPA-54 section 10.5.4.2 by adding a second exception as follows: Existing chimneys shall be permitted to have their use continued when a gas conversion burner is installed, and shall be equipped with a manually reset device that will automatically shut off the gas to the burner in the event of a sustained back-draft.
  • Page 34 P52DF Single Sided Gas Fireplace XG0196 - 150204.3...

Table of Contents