Accessories; Drive Roll Kits; Aluminum Feeding Kit; Readi-Reel Adapter - Lincoln Electric POWER MIG IM736-D Operator's Manual

C-1

DRIVE ROLL KITS

Refer to Table C.1 for various drive roll kits that are
available for the POWER MIG. All items in Bold are
supplied standard with the POWER MIG.
TABLE C.1
Wire Size
.023"-.030" (0.6-0.8 mm)
Solid
.035" (0.9 mm)
Steel
.045" (1.2 mm)
.040" (1.0mm)
.035-.045" (0.9-0.2mm)
.035" (0.9 mm)
Cored
.045" (1.2 mm)
Aluminum 3/64" (1.2 mm)
*
.035 Aluminum recommended for Push-Pull systems only.
3/64" (1.2 mm) ALUMINUM
FEEDING KIT (K2153-1)
This kit helps push feeding aluminum through stan-
dard machine feeder and gun. It provides gun and
wire drive conversion parts to weld with 3/64" (1.2
mm) aluminum wire. 5356 alloy aluminum wire is rec-
ommended for best push feeding performance.
Kit includes drive rolls and wire guide plate for the
wire drive, liner and two contact tips for the gun, along
with installation instructions.
K363P READI-REEL ADAPTER
The K363P Readi-Reel Adapter mounts to the 2"
spindle. It is needed to mount the 22-30 lb. Readi-
Reels.

DUAL CYLINDER MOUNTING KIT

(K1702-1)
Permits stable side-by-side mounting of two full size
(9" dia. x 5' high) gas cylinders with "no lift" loading.
Simple installation and easy instructions provided.
Includes upper and lower cylinder supports, wheel
axles and mounting hardware.
ALTERNATIVE MAGNUM GMAW
GUN AND CABLE ASSEMBLIES
The following Magnum 300 gun and cable assemblies
are separately available for use with the POWER MIG
300. Each is rated 300 amps 60% duty cycle (or 300
amps 40% duty) and is equipped with the integrated
connector, twist-lock trigger connector, fixed nozzle
and insulator, and includes a liner, diffuser, and con-
tact tips for the wire sizes specified:

ACCESSORIES

Drive Roll Kit

MAGNUM GUN CONNECTION KIT

(Optional K466-6)
KP1696-030S
Using the optional K466-6 Magnum Connection kit for
KP1696-035S
the POWER MIG permits use of standard Magnum
KP1696-045S
200, 300 or 400 gun and cable assemblies.
KP-1696-2
KP-1696-1
K1692-2
KP1697-035C
When the POWER MIG Gun Selector Switch is in the
KP1697-045C
"Standard / Spool Gun" position, the POWER MIG pro-
KP1695-3/64A
vides gun trigger switch transfer between the Magnum
gun or the spool gun for the same polarity welding with
different wire and gas processes.
Closing either gun trigger will cause the electrode of
both guns to be electrically "HOT". Be sure unused
gun is positioned so electrode or tip will not contact
metal case or other metal common to work.
-----------------------------------------------------------------------
Because the control circuitry senses each gun through
its trigger leads, weld parameters are displayed and
adjustable for the last gun that was triggered.
1. Pulling the trigger for the built-in feeder gun
2. Pulling SPOOL GUN Trigger:
3. Operation with POWER MIG 300:
POWER MIG 300
English Wire
Length Part No.
10' (3.0 m) K470-1
12' (3.6 m) K470-7 .035 – .045"
15' (4.5 m) K470-3
SPOOL GUN (PRINCE
CAUTION
(Magnum 300):
Disables spool gun operation.
•
Changes the displays of the POWER MIG 300 to
•
correspond to feeder gun operation.
Closing feeder gun trigger starts feeder gun weld-
•
ing and makes both electrodes electrically "HOT".
Disables built-in feeder gun operation.
•
• Changes the displays of the POWER MIG 300 to
correspond to Spool Gun operation.
Closing spool gun trigger starts spool gun welding
•
and makes both electrodes electrically "HOT".
Install the spool gun per the installation instructions
•
Turn the POWER MIG 300 input power ON.
•
Make sure that the Gun Selector Switch is in the
•
"Standard / Spool Gun" position.
• Pull and release the trigger of the Spool Gun. The
Power Mig recognizes the spool gun as active and weld
parameters are adjustable for welding with the Spool
Gun
C-1
Metric Wire
Size Size
0.9 – 1.2 mm
TM XL)