Sony SRW-5000 Operation Manual page 87

To enter the current time code continuously
1
Set the VTR SETUP menu item 127 "Tele-File IN
OUT Input Continue" to "on".
2
Use the cursor buttons to move the cursor to the IN/
OUT section to be entered.
To move the cursor using the numeric buttons
Enter the line number using the numeric buttons. Then
press the [F9] (CUENUM POINT) button. The cursor
will move to the line specified by the numeric buttons.
3
Press the IN button or OUT button while holding down
down the ENTRY button.
The movement of the cursor is automatic (as described
in the following table) and data is entered
continuously.
Input When the IN button
condition you press while
holding down the
ENTRY button
Only IN point IN point data is
data has been modified and the
entered cursor stays on the IN
point data.
Only OUT IN point data is
point data has entered and the
been entered cursor moves to the
next IN point.
To display the duration between an IN point and
an OUT point
Use the cursor buttons to move the cursor to the IN/OUT
section and press the IN button and OUT button at the
same time. The duration between two points appears while
the buttons are pressed.
To preroll to an IN/OUT point
Use the cursor buttons to move the cursor to the IN/OUT
section and press the IN button (to preroll to an IN point)
or OUT button (to preroll to an OUT point) while holding
down the PREROLL button. The VTR prerolls to the point
and stops.
For details on setting the preroll time, see "4-2-6 Setting
the Preroll Time (PREROLL TIME)" on page 55.
Note
If the cursor is not on the IN/OUT section when pressing
the IN/OUT button while pressing the PREROLL button,
the VTR prerolls to the cue point. When pressing the
PREROLL button only, the VTR prerolls to the cue point
regardless of the cursor position.
Automatic time data changes during IN/OUT
point data entry or modification
The table below shows the automatic changes that occur in
time data when either the IN point or OUT point is
changed.
When IN point data is entered or modified:
Status of input data
The time sequence of the IN/
OUT point data is correct.
The time sequence of the IN/
OUT point data is not correct.
The OUT point has not been
input.
When OUT point data is entered or modified:
Status of the input data
The time sequence of the IN/
When the OUT
OUT point data is correct.
button you press
while holding
The time sequence of the IN/
down the ENTRY
OUT point data is not correct.
button
The IN point has not been
OUT point data is
input.
entered and the
Changing Tk data
cursor moves to the
next IN point.
Use the cursor buttons to move the cursor to the take data
to be changed. Then use the numeric buttons to change the
OUT point data is
modified and the value. Note that values from 0 to 255 can be entered. Or,
cursor stays on the
move the cursor to the take data, and press the [F4]
OUT point.
(CHANGE DATA) button or the + button repeatedly to
increase the value in increments of 1. Press the – button
repeatedly to decrease the value in increments of 1. Note
that the value cannot go below 0.
Copying data
Use the cursor buttons to move the cursor to the destination
Mrk or Tk data, and press the RCL button. The Tk data
from the line above is copied to the selected line.
Changing Cut data
Use the cursor buttons to move the cursor to the cut data to
be changed, and then enter the new data using the numeric
buttons and +/– buttons. Pressing the – button enters the
tilde (~). Press the numeric buttons while pressing down
the SFT button to enter uppercase letters (A to J). Note that
a maximum of four characters can be entered.
Or, do the procedure below to change the data.
IN point OUT point
The data is The data is
changed. unchanged.
The data is The data is
changed. deleted.
The data is The data is
changed. unchanged.
IN point OUT point
The data is The data is
unchanged. changed.
The data is The data is
unchanged. unchanged.
The data is The data is
unchanged. changed.
4-4 CUE Menu
87